Metra 99-3528 Manual de Usario

Lee a continuación 📖 el manual en español para Metra 99-3528 (4 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 7/30/2015 INST99-3528
Installation instructions for part 99-3528
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
DIN radio provision with pocket
A) Radio Housing
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-1784
Antenna Adapter: • 40-VW10
86-3528 Radio Removal Keys • Panel Removal Tool Phillips Screwdriver
TOOLS REQUIRED
Pontiac GTO 2004-2006
99-3528
A
Dash Disassembly ................................................. 2
Kit Assembly
DIN radio provision with pocket ............................ 3
Table of Contents
99-3528
2
1.
Using the radio removal keys, pull
the factory radio from the dash and
disconnect the wiring. (Figure A)
2. Unsnap and remove the trim panel
at the top center of the dash above
the A/C vents and remove (4)
Phillips screws. (Figure B)
3.
Remove (1) Phillips screw from inside
lower open storage area where center
console and dash meet. (Figure C)
4. Unsnap and remove center console
(open center armrest/ storage
compartment and work forward).
(Figure D)
Dash Disassembly
5. Remove (2) Phillips screws
exposed at the bottom of the
center panel surrounding radio and
remove panel. (Figure E)
6. Unclip and remove trim panel
surrounding radio and A/C controls.
7. Remove (3) Phillips screws holding
“cage” in radio opening. (Figure F)
8. Pull down on the “cage” from the
opening inside on the top and
remove. (Figure G)
Continue to kit assembly
(Figure B) (Figure E)
(Figure C) (Figure F)
(Figure D) (Figure G)(Figure A)
99-3528
Kit Assembly
(Figure A)
(Figure B)
DIN radio provision with pocket
1. Remove the metal DIN sleeve from
the aftermarket radio.
2. Slide the sleeve into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
3. Slide the radio back into the sleeve
until it clicks in. (Figure B)
4. Reassemble the dash in reverse
order of disassembly, leaving the
cage removed in disassembly out.
5. Locate the factory wiring harness
and antenna plug in the dash and
make all necessary connections
to the radio. Metra recommends
using the proper mating adapters
from Metra and/or AXXESS.
Re-connect the negative battery
terminal and test the radio for
proper operation.
6. Snap the completed assembly into
the dash until secure.
3

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 99-3528

¿Necesitas ayuda?

Si necesitas ayuda con Metra 99-3528 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales