Metra 99-7377B Manual de Usario

Lee a continuación 📖 el manual en español para Metra 99-7377B (4 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
REV. 1/24/2017 INST99-7377B
INSTALLATION INSTRUCTIONS FOR PART 99-7377B
METRA – The World’s best kits.®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
CAUTION!
All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
ISO DIN radio provision with pocket
Painted matte black
A) Radio trim panel • B) Radio brackets C) Pocket • D) (4) #8 x 3/8” Phillips screws E) (2) Panel clips
20;-,(;<9,:
20;*64765,5;:
>0905.(5;,55(*655,*;065:
Wiring Harness: • 70-7304 (sold separately) Antenna Adapter: • Not required
Panel removal tool • Phillips screwdriver
;663:9,8<09,+
Kia Optima 2016-up
99-7377B
Table of Contents
A B C D E
Dash Disassembly ................................................. 2
Kit Preparation ....................................................... 3
Kit Assembly .......................................................... 3
99-7377B
2
Dash Disassembly
1. Open the glove box and remove the
trim at the top of the opening, and
then remove the (2) Phillips screws
exposed. (Figure A)
2. Unclip the trim that runs along the
dash from the right side A/C vent
to the steering column, and then
remove the (2) Phillips screws
securing the A/C vent/hazard panel.
(Figure B)
3. Unclip and remove the right side
trim panel from the center console,
and then remove the (1) Phillips
screw securing the A/C vent/hazard
panel. (Figure C)
4. Unclip the A/C vent/hazard panel,
disconnect the hazard switch, and
then remove the panel. (Figure D)
5. Using caution not to break the
panel, carefully unclip and remove
the radio trim panel. (Figure D)
(Figure B)
(Figure D)
(Figure A) (Figure C)
Note: There are (8) clips that attach
the panel to the vehicle: (2) at
the top-middle, (2) at the bottom
corners, (2) at the top corners, and
(2) in the center (these 2 are only in
non-nav models). (Figure E)
6. Remove the (4) Philips screws
securing the radio and then remove.
Continue to Kit Preparation
(Figure E)
non-NAV only
99-7377B
3
(Figure B)
(Figure A)(Figure A)
Kit AssemblyKit Preparation
ISO DIN radio provision with pocket
1. Attach the pocket radio to the
brackets using the (4) #8 x 3/8”
Phillips screws provided. (Figure A)
2. Remove the metal DIN sleeve and
trim ring from the aftermarket radio.
3. Slide the radio into the bracket/
pocket assembly and then secure it
using the screws supplied with the
radio. (Figure B)
4. Locate the factory wiring harness
and connector in the dash and
complete all necessary connections
to the radio. Metra recommends
using the proper mating adapter
from Metra and/or Axxess. Test the
radio for proper operation.
5. Secure the completed assembly into
the dash using the factory screws.
6. Snap the radio trim panel over the
completed assembly, and then
reassemble the dash in reverse
order of disassembly.
1. Attach the (2) to thepanel clips
radio trim panel as shown.
(Figure A)
Continue to Kit Assembly

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 99-7377B

¿Necesitas ayuda?

Si necesitas ayuda con Metra 99-7377B haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales