Metra 99-7378B Manual de Usario

Lee a continuación 📖 el manual en español para Metra 99-7378B (4 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
REV. 2/10/2017 INST99-7378B
INSTALLATION INSTRUCTIONS FOR PART 99-7378B
METRA – The World’s best kits.®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
CAUTION!
All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
ISO DIN radio provision with pocket
Painted scratch resistant matte black
A) Radio trim panel • B) Radio brackets C) Pocket • D) (2) #8 x 3/8” Phillips screws
20;-,(;<9,:
20;*64765,5;:
>0905.(5;,55(*655,*;065: (sold separately)
Wire harness: 70-7304
Antenna adapter: • 40-KI11
Panel removal tool • Phillips screwdriver
;663:9,8<09,+
Kia Sportage LX 2017-up (with 5 screen)
99-7378B
Table of Contents
A B C D
Dash Disassembly ................................................. 2
Kit Preparation ....................................................... 3
Kit Assembly .......................................................... 3
99-7378B
2
Dash Disassembly
 Unclip and slide the top of the
center console (including the cup
holders) back slightly. (Figure A)
 Open the passenger door, and then
unclip and remove the dashboard
trim panel. Remove (1) Phillips
screw exposed. (Figure B)
 Unclip and remove the entire panel
that is above the glove box, and
below the radio. (Figure C)
 Remove (2) Phillips screws from
the radio/vent panel, and then
unclip and remove. (Figure D)
 Remove (4) Phillips screws
securing the radio, and then
unplug and remove.
Continue to Kit Preparation
(Figure A) (Figure C)
(Figure B) (Figure D)
99-7378B
3
Kit Preparation Kit Assembly
ISO DIN radio provision with pocket
1. Attach the pocket radio to the
brackets using the (2) supplied
#8 x 3/8” Phillips screws. (Figure A)
2. Remove the metal DIN sleeve and
trim ring from the aftermarket radio.
3. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure B)
4. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Test the radio for proper
operation.
5. Secure the completed assembly
into the dash using the factory
hardware, and then reassemble
the dash in reverse order of
disassembly.
From the factory radio/vent panel:
1. Remove (4) screws securing the inner radio trim panel to the panel, and then
unclip and remove. (Figure A)
2. Attach the 99-7378B radio trim panel to the factory radio/vent panel, and then
secure using the factory hardware. (Figure A)
Continue to Kit Assembly
REAR VIEW
OF
FACTORY RADIO/VENT PANEL
(Figure B)
(Figure A)
(Figure A)

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 99-7378B

¿Necesitas ayuda?

Si necesitas ayuda con Metra 99-7378B haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales