Metra 99-7630 Manual de Usario

Lee a continuación 📖 el manual en español para Metra 99-7630 (6 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/6
REV. 2/11/2016 INST99-7630
INSTALLATION INSTRUCTIONS FOR PART 99-7630
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
CAUTION!
All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
ISO DIN radio provision with pocket
ISO DDIN radio provision
Painted to match the factory color and finish
A) Radio trim panel • B) Radio brackets • C) Pocket D) (8) #8 x 3/8” Phillips screws
E) (8) #4 x 1/2” Phillips screws • F) (6) Panel clips
20;-,(;<9,:
20;*64765,5;:
>0905.(5;,55(*655,*;065: (sold separately)
Wiring Harness: • 70-7552 (non-amplified models only)
Antenna Adapter: 40-NI12
Panel removal tool • Phillips screwdriver
Torx screwdriver
;663:9,8<09,+
Nissan Maxima 2016-up
99-7630
A
Table of Contents
BCE FD
Dash Disassembly ................................................. 2
Kit Preparation ....................................................2-3
Kit Assembly
ISO DIN radio provision with pocket ...................... 4
ISO DDIN radio provision ...................................... 5
99-7630
2
Dash Disassembly Kit Preparation
1. Pull down on the shift collar,
remove the clip holding the shift
knob, and then remove the knob.
2. Open the center console
compartment. Using a panel
removal tool, pry up on the rear of
the center console trim panel, and
then unplug and remove the panel.
3. Unclip and remove the vent/
hazard-switch trim panel above
the radio.
4. Remove (4) Phillips screws
securing the radio/climate-control
panel, then unplug and remove
the panel.
Continue to kit preparation.
From the factory radio/climate-
control panel:
1. Remove the (4) Phillips screws
securing the climate-controls and
then remove.
2. Unclip and remove the passenger
airbag light.
3. Unscrew (4) Phillips screws and
remove the radio/climate-control
side trim panels from the radio
panel (save for kit assembly).
4. Remove the (2) Torx screws
securing the climate-control
module below the radio and then
remove.
Continued on the next page.
Refer to metraoline.com for
dash disassembly images.
Refer to metraoline.com for kit
preparation images.
99-7630
3
Kit Preparation
From the 99-7630 radio trim panel
5. Attach the (6) provided. panel clips
(Figure A)
6. Secure the climate controls to
the panel using the (4) #4 x 1/2
Phillips screws provided.
(Figure B)
7. Snap the passenger airbag light
through the front of the panel.
(Figure B)
8. Using the (4) #4 x 1/2” screws
provided, secure the radio/climate-
control side trim panels. (Figure C)
9. Secure the radio brackets to the
panel using the (4) #8 x 3/8
Phillips screws provided.
(Figure C)
10. Using the factory hardware, secure
the climate-control module to the
lower portion of bracket/panel
assembly. (Figure D)
Continue to kit assembly.
(Figure C)
(Figure D)(Figure B)
(Figure A)

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 99-7630

¿Necesitas ayuda?

Si necesitas ayuda con Metra 99-7630 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales