Metra 99-8238 Manual de Usario

Lee a continuación 📖 el manual en español para Metra 99-8238 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
The World’s best kits.®MetraOnline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 8/28/17 INST99-8238
I N S TA L L AT I O N I N S T R U C T I O N S
99-8238
KIT FEATURES
• DIN radio provision with pocket
• ISO DIN radio provision with pocket
KIT COMPONENTS
• A) Radio housing • B) Radio brackets • C) ISO snap-in brackets • D) Trim plate
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 10mm socket wrench
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly
–DIN radio provision with pocket ........................3
–ISO DIN radio provision with pocket ..................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: • 70-1761
Antenna Adapter: • Not required (sedan)
• 40-LX11 (hatchback)
Steering Wheel Control Interface: ASWC-1
A B C D
Toyota Yaris 2012-2017
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and remove entire panel
including a/c vent on passenger side of
dash. (Figure A)
2. Unclip and remove the panel from
around the radio. (Figure B)
3. Remove (4) 10mm bolts and remove
factory radio. (Figure C)
Continue to Kit Assembly
(Figure A)
(Figure C)
(Figure B)
REV. 8/28/2017 INST99-8238 3
KIT ASSEMBLY
DIN radio provision with pocket
1. Slide the
radio brackets
onto the sides
of the
radio housing
until the side clips
engage.
Note:
Tabs are marked Left and Right.
(Figure A)
2. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
3. Slide the sleeve into the
radio housing
and secure by bending the metal locking
tabs down. (Figure B)
4. Slide the radio back into the sleeve until
it clicks in. (Figure C)
5. Snap the
trim plate
into the
radio
housing
. (Figure C)
6. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra. Test
the radio for proper operation.
7. Reassemble the dash in reverse order
of disassembly.
(Figure A) (Figure A)
(Figure B) (Figure B)
(Figure C) (Figure C)
ISO DIN radio provision with pocket
1. Slide the
radio brackets
onto the sides
of the
radio housing
until the side clips
engage.
Note:
Tabs are marked Left and Right.
(Figure A)
2. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
3. Secure the
ISO brackets
to the radio
with the screws supplied with the radio.
(Figure B)
4. Slide the bracket/radio assembly into
the radio opening until the side clips
engage. (Figure C)
5. Snap the
trim plate
into the
radio
housing
. (Figure C)
6. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra. Test
the radio for proper operation.
7. Reassemble the dash in reverse order
of disassembly.

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 99-8238

¿Necesitas ayuda?

Si necesitas ayuda con Metra 99-8238 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales