Metra 99-9008 Manual de Usario

Metra No categorizado 99-9008

Lee a continuación 📖 el manual en español para Metra 99-9008 (4 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

REV. 1/25/2016 INST99-9008

Installation instructions for part 99-9008

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con-

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DIN radio provision

• DIN radio provision

Aftermarket radios are equipped with a trim ring surrounding the face of

the radio. Since some installers prefer the trim ring equipped with the radio

(DIN) and others do not (ISO DIN), this kit was designed to allow the installer

to choose.

• A) ISO DIN housing • B) ISO DIN trim plate • C) ISO DIN brackets • D) DIN trim plate

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1784

Antenna Adapter: • 40-VW54

• 86-9001 radio removal keys • Torx T-10 driver

TOOLS REQUIRED

Volkswagen Beetle 1998-2010

99-9008

A B C

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DIN radio provision......................................... 3

– DIN radio provision............................................ 4

Table of Contents

99-9008

1. Insert the long end of the 86-9001

radio removal tool into the slots in

the factory radio (flat sides pointing

out), and then pull the radio out.

Disconnect all connectors and then

remove the radio. (Figure A)

2. For ISO DIN radio installations only,

remove (2) Torx T-10 screws exposed

in the radio cavity. (Figure A)

Continue to kit assembly

Dash Disassembly

(Figure A)

99-9008

ISO DIN radio provision

1. Remove the metal DIN sleeve and

trim ring from the aftermarket radio

2. Align the holes in the ISO DIN

brackets with the holes in the radio

and then secure the brackets to

the radio with the

screws included

with the radio. (Figure A)

Note: The screws provided with

certain radios may create a

clearance problem during radio

installation. In these cases it may

be necessary to trim the walls

of the dash bezel to provide the

proper clearance.

3. Locate the factory wiring harness

and antenna connector in the

dash and make all necessary

connections to the radio. Metra

recommends using the proper

mating adapters from Metra and/or

AXXESS. Re-connect the negative

battery terminal and test the radio

for proper operation.

4. Slide the radio into the radio cavity

until it clicks in. (Figure B)

5. Position the ISO DIN housing over

the radio with the side notches in

the upper corners. Secure with the

(2) Torx T-10 screws removed in

dash disassembly. (Figure C)

6. Attach the ISO DIN trim plate onto

the . (Figure D)ISO DIN housing

(Figure B) (Figure D)

(Figure A)

Kit Assembly

(Figure C)

Especificaciones del producto

Marca:	Metra
Categoría:	No categorizado
Modelo:	99-9008
Amable:	Alles-in-één vloeistofkoeler
País de origen:	China
Material de tubería/manguera:	Rubber
Cantidad por paquete:	1 stuk(s)
Flujo de aire máximo:	66.04 cfm
numero de fans:	3 ventilator(en)
Ubicación adecuada:	Processor
Código del Sistema Armonizado (SA):	84733080
Nivel de ruido ventilación (máx.):	31.6 dB
Diámetro del ventilador:	120 mm
Velocidad del motor de la bomba (máx.):	3300 RPM
Zócalos de procesador compatibles:	LGA 1150 (Socket H3), LGA 1151 (Socket H4), LGA 1155 (Socket H2), LGA 1156 (Socket H), LGA 1200 (Socket H5), LGA 2011 (Socket R), LGA 2011-v3 (Socket R), LGA 2066, Socket AM4
Presión de aire máxima:	1.9 mmH2O
Soporte de modulación de ancho de pulso:	Ja
Ventilador de alimentos (ancho x fondo x alto):	120 x 120 x 25 mm
Longitud del tubo:	400 mm
Conector del ventilador:	4-pin
Velocidad del ventilador (máx.):	2200 RPM
Material del radiador:	Aluminium
Velocidad del motor de la bomba (mín.):	1000 RPM
Velocidad del ventilador (mín.):	550 RPM
Fan Dikhaid:	25 mm
Ancho del radiador:	395 mm
Profundidad del radiador:	120 mm
Altura del radiador:	27 mm
Conector de pompa:	4-pin
pompbreedte:	88 mm
Profundidad de la bomba:	70 mm
pomphoogte:	64 mm