Metra 99-9229G Manual de Usario

Metra No categorizado 99-9229G

Lee a continuación 📖 el manual en español para Metra 99-9229G (4 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

REV. 9/10/2015 INST99-9229G

Installation instructions for part 99-9229G

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con-

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted to match factory finish

• A) Radio trim panel • B) Radio housing • C) Pocket • D) (4) #8 x 3/8” Phillips screws • E) (4) Panel clips

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-9221

Antenna Adapter: • 40-VL10

• Panel removal tool • Phillips screwdriver • T-25 Torx driver

TOOLS REQUIRED

Volvo S60/V70 2001-2004

99-9229G

A B C

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DIN radio provision with pocket ...................... 3

–ISO DDIN radio provision ...................................... 3

Table of Contents

D E

99-9229G

1. Remove the panel between the

climate control and gear selector.

(Figure A)

2. Move the gear selector as far back

as possible, unsnap the panel

surrounding it, and then rotate it

45 degrees either way. (Figure B)

3. Remove (2) T-25 screws now

exposed securing the climate

control panel to the vehicle, and

then remove. (Figure C)

Continue to 3 a.

Dash Disassembly

a. Angle the panel outwards so

that it is possible to insert a

couple of fingers between the

center console and the side of

the panel. (Figure D)

b. Remove the panel by pulling

it downward, maintaining the

same angle. Some force is

required because the panel is

tightly installed. (Figure D)

c. Do not unplug the connectors.

Place the panel to one side instead

4. Remove (2) T-25 Torx screws

securing the radio, and then

remove. (Figure E)

5. Remove the sub-dash bracket from

the radio, and then remove.

a. Remove (5) T-25 Torx screws

securing the bracket. (Figure F)

b. Depress the snaps on the top

and bottom of the pocket.

(Figure G)

Continue to kit assembly

(Figure B) (Figure E)

(Figure A)

(Figure C) (Figure F)

(Figure D) (Figure G)

99-9229G

Kit Assembly

ISO DIN radio provision with pocket

1. Secure the pocket radio to the

housing using (4) #8 x 3/8” Phillips

screws provided. (Figure A)

Note: Rounded edge of pocket

faces towards the bottom.

2. Remove the metal DIN sleeve and

trim ring from the aftermarket radio.

3. Slide the radio into the completed

assembly, and then secure it to the

assembly using screws supplied

with the radio. (Figure A)

Locate the factory wiring harness and

antenna connector in the dash, and

complete all necessary connections to the

radio. Metra recommends using the proper

mating adapter from Metra and/or AXXESS.

Re-connect the negative battery terminal

and test the radio for proper operation.

5. Reassemble the dash in reverse

order of disassembly.

6. Attach (4) panel clips supplied to

the , and then snap radio trim panel

the panel over the radio.

ISO Double DIN radio provision

1. Slide the radio into the radio

housing and secure it using screws

supplied with the radio.

(Figure A)

2. Locate the factory wiring harness

and antenna connector in the

dash, and complete all necessary

connections to the radio. Metra

recommends using the proper

mating adapter from Metra and/or

AXXESS. Re-connect the negative

battery terminal and test the radio

for proper operation.

3. Reassemble the dash in reverse

order of disassembly.

4. Attach (4) panel clips supplied to

the , and then snap radio trim panel

the panel over the radio.

(Figure A) (Figure A)

Especificaciones del producto

Marca:	Metra
Categoría:	No categorizado
Modelo:	99-9229G

¿Necesitas ayuda?

Si necesitas ayuda con Metra 99-9229G haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado Metra Manuales

Metra 71-017C Manual de Usario

26 Septiembre 2024

Metra AXSP-HK Manual de Usario

26 Septiembre 2024

Metra 109-TO7 Manual de Usario

24 Septiembre 2024

Metra 95-8273B Manual de Usario

19 Septiembre 2024

Metra 95-7822 Manual de Usario

19 Septiembre 2024

Metra 82-8703 Manual de Usario

19 Septiembre 2024

Metra 88-00-9004 Manual de Usario

19 Septiembre 2024

Metra 82-9101 Manual de Usario

19 Septiembre 2024

Metra 95-7021HG Manual de Usario

19 Septiembre 2024

Metra 82-5608 Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024