Metra 99-9721 Manual de Usario

Lee a continuación 📖 el manual en español para Metra 99-9721 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 1/5/18 INST99-9721
I N S TA L L A T I O N I N S T R U C T I O N S
99-9721
KIT FEATURES
ISO DIN radio provision with pocket
ISO DDIN radio provision
Textured panel
Integrated tinted splash guard
KIT COMPONENTS
• A) Radio trim panel • B) Sub-bracket • C) Splash guard • D) Radio brackets • E) Pocket • F) (8) #8 x 3/8” Phillips screws
• G) (1) #6 x 1/2” Phillips screw • H) Felt tape (not shown) TOOLS REQUIRED
• Panel removal tool • 13mm Socket wrench
• T-10, T-25 and T-40 Torx drivers • Pick tool or
small flat blade screwdriver (to remove push pins)
TABLE OF CONTENTS
Dash Disassembly ...............................................2-3
Kit Preparation ................................................... 4-5
Kit Assembly ...................................................... 6-7
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wire harness: • 70-9701
Antenna Adapter: • Not required
A B C D E
F G
Polaris Slingshot 2015-up*
*Visit MetraOnline.com for up-to-date vehicle specific applications.
1.800.221.0932
|
MetraOnline.com
2
1. Remove (4) T-10 screws from the radio
trim, then remove and set aside.
(Figure A)
2. Unclip, then unplug and remove the
radio controller. (Figure B)
3. Remove (3) T-25 screws from the
windshield, then remove and set aside.
4. Unclip the (2) painted panels at the top
of the radio opening. (Figure C)
5. Remove (2) push pins at the top of the
dash/console side trims, then unclip and
remove the trims. Lift up on the Tip:
panel starting from the rear, between
the seats. (Figure D)
Continued on the next page
DASH DISASSEMBLY
(Figure B)
(Figure A) (Figure C)
(Figure D)
REV. 1/5/2018 INST99-9721 3
DASH DISASSEMBLY (CONT.)
(Figure E)
(Figure F)
(Figure G)
(Figure H)
6. Remove (2) push pins inside the radio
cavity behind the start/stop button.
(Figure E)
7. Remove the 13mm bolt holding each
mirror to its base, then set the mirrors
aside. The bases do not need to Note:
be removed, but can be if so desired.
(Figure F)
8. Remove (2) T-25 screws from
underneath each of the (2) painted dash
side trims from under the front side
of each trim, then unclip and remove.
(Figure G)
9. Remove (8) T-40 screws holding the
top dash panel, then if the mirror bases
were not removed in step 7, pull each
side over the mirror base (1 side at a
time). (Figure H)
10. Lift the dash trim and unplug the
buttons and switches by the radio
opening. (Figure H)
11. The dash panel is now free, lift up to
remove and set aside. (Figure H)
Continue to Kit Preparation

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 99-9721

¿Necesitas ayuda?

Si necesitas ayuda con Metra 99-9721 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales