Metra Axxess AX-ADCH02 Manual de Usario

Metra No categorizado Axxess AX-ADCH02

Lee a continuación 📖 el manual en español para Metra Axxess AX-ADCH02 (16 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/16
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
AX-ADCH02
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 6/26/18 INSTAX-ADCH02
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun, solder,
and heat shrink • Small flat-blade screwdriver
• Tape • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections to be made
For models
without
an amplifier .......................3
For models
with
an amplifier ............................4
Installing & programming the AX-ADCH02
AX-ADBOX1 ...........................................................5
AX-ADBOX2 ..........................................................6
Adjusting the AX-ADCH02 .....................................7
Chrysler Data Interface 2007-up*
APPLICATIONS
See inside front cover
Provides accessory power (12-volt 10-amp)
Maintains the retained accessory power (R.A.P.) feature
Provides NAV outputs (parking brake, reverse, speed sense)
Retains safety chimes
Pre-wired ASWC-1 harness (ASWC-1 sold separately)
Can be used in both amplified and non-amplified models
Retains balance and fade†
Retains Blind Spot Detection (if equipped)
Micro “B” USB updatable
• AX-ADCH02 harness
• 4-pin harness with stripped leads
*Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
INTRODUCTION
The AX-ADCH02 harness is designed for, and must be used with, the
AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the
AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads
.
† To retain fade in amplified models, use the AX-ADBOX1
2
APPLICATIONS
CHRYSLER
200 2011-2014
300 2008-2010
Aspen 2008-2009
Sebring 2007-2010
Town & Country 2008-2017
DODGE
Avenger 2008-2014
Caliber 2009-2010
Caravan/
Grand Caravan 2008-up
Challenger 2009-2014
Charger 2008-2010
Dakota 2008-2011
Durango 2008-2013
Journey 2009-2010
Magnum 2008-2009
Nitro 2007-2011
Ram 1500 2009-2011
Ram 2500/3500 2010-2011
JEEP
Commander 2008-2010
Compass 2009-2017.5
Grand Cherokee 2008-2013
Liberty 2008-2012
Patriot 2009-2017
Wrangler 2007-2017
Wrangler
(JK body type) 2018
MITSUBISHI
Raider 2008-2009
RAM
1500/2500/3500 2012
C/V Tradesman 2012-2015
VOLKSWAGEN
Routan 2009-2013
3
REV. 6/26/2018 INSTAX-ADCH02
From the AX-ADCH02 harness to the aftermarket radio:
Connect the wire to the ground wire.Black
Connect the Yellow wire to the battery wire.
If installing an ASWC-1 (sold separately), connect the wire to accessory power.Red
Connect the wire to the power antenna wire.Blue/White
Ensure the (2) 4-pin Molex connectors (with green purple and wires) are connected together
.
Connect the
4-pin harness with stripped leads
, to the 4-pin Molex connector
(with and wires).gray white
Attention! The following (4) wires are reversed on purpose. These wires will not match “color
code” to the aftermarket radio.
Connect the wire to the right front positive speaker output.Green
Connect the wire to the right front negative speaker output.Green/Black
Connect the wire to the left front positive speaker output.Purple
Connect the wire to the left front negative speaker output.Purple/Black
12-pin pre-wired ASWC-1 harness:
This harness is to be used along with the optional ASWC-1 (sold separately) to retain steering
wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If the ASWC-1
will be used, please refer to the ASWC-1 instructions for radio connections and programming.
Disregard the harness that comes with the ASWC-1.
Continue to Installing & Programming the AX-ADCH02
CONNECTIONS TO BE MADE
Attention! This interface will work with models that are either non-amplified, or amplified.
Please follow the instructions carefully for your model vehicle. Failure to do so will result in
either no sound, or low sound. If you are unsure if your vehicle is factory amplified or not, please
contact your local dealership.
For models
without
an amplifier:
From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):
Connect the wire to the accessory wire.Red
If installing an ASWC-1 (sold separately), connect the wire on the AX-ADCH02 Note: Red
harness as well.
If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
Attention! The following (4) wires are reversed on purpose. These wires will not match “color
code” to the aftermarket radio.
Connect the wire to the right rear positive speaker output.Gray
Connect the Gray/Black wire to the right rear negative speaker output.
Connect the wire to the left rear positive speaker output.White
Connect the wire to the left rear negative speaker output.White/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the wire to the VSS/speed sense wire.Blue/Pink
Connect the wire to the reverse wire.Green/Purple
Connect the wire to the parking brake wireLight Green
Tape off and disregard the following (6) wires, they will not be used in this application:
Blue/White Brown Green Green/Black Purple Purple/Black, , , , ,

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: Axxess AX-ADCH02

¿Necesitas ayuda?

Si necesitas ayuda con Metra Axxess AX-ADCH02 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales