Metra NITO-01 Manual de Usario

Metra No categorizado NITO-01

Lee a continuación 📖 el manual en español para Metra NITO-01 (5 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/5

Installation instructions for part NITO-01

REV. 5/17/2017 INSTNITO-01

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Provides NAV outputs (parking brake,

reverse, and speed sense)

• Pre-wired ASWC-1 harness (ASWC-1 sold

separately)

• Retains the factory backup camera

• Retains the audible parking sensor warning

• Retains the factory AUX-IN jack

• Used in amplified applications

• Adjustable gain control for overall volume

• High level speaker input

• Retains balance

• Micro “B” USB updatable

INTERFACE FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape • Small flat-blade screwdriver

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

NITO-01

Nissan Maxima 2016 Amplifier Interface

• NITO-01 interface • NITO-01 harness

• 16-pin harness with stripped leads • AX-CAM6V 12-volt to 6-volt converter

INTERFACE COMPONENTS

Connections to be made ................................................... 2

Installing the NITO-01 ....................................................... 3

Initializing the NITO-01 ..................................................... 3

Adjusting the NITO-01 ...................................................... 3

Extra settings .................................................................... 4

Table of Contents

NITO-01

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

Note: If installing an ASWC-1 (sold separately), there will be an accessory wire

there to connect as well.

• Connect the Blue/White wire to the amp turn on wire. This wire must be

connected to hear sound from the factory amplifier.

•

Tape off and disregard the following (13) wires, they will not be used in this

application: Blue/Pink

Blue/White Brown Gray Gray/Black Green Green/, , , , ,

Black Green/Purple Purple Purple/Black, , ,

, , , Light Green White White/Black

From the NITO-01 harness to the aftermarket radio:

• Connect the Black wire with a ring terminal to chassis ground.

• Connect the Yellow wire to the battery wire.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

Note: Before connecting this wire, also refer to the “AX-CAM6V 12-volt to

6-volt” converter section.

• Connect the Light Green wire to the parking brake wire.

• If retaining the factory AUX-IN jack, connect the & RCA jacks to the Red White

AUX input.

• If retaining the factory backup camera, connect the Yellow RCA jack to the

reverse camera input. Please reference “Reverse camera operation” on page 4

if retaining the camera.

AX-CAM6V 12-volt to 6-volt converter:

• Connect the Black wire to chassis ground.

• Connect the Blue/Red Red wire to the wire labeled “Camera Power 6V”.

• Connect the Blue/White Green/Purple wire to the wire.

Note: The wire will connect to both the AX-CAM6V, and the Green/Purple

aftermarket radio.

12-pin pre-wired ASWC-1 harness:

• This harness is to be used along with the optional ASWC-1 (not included) to

retain steering wheel audio controls. If the ASWC-1 is not being used, disregard

this harness. If it will be used, please refer to the ASWC-1 instructions for radio

connections, and also to the ASWC-1 settings on page 4 of these instructions.

Note: Disregard the harness that comes with the ASWC-1.

• Connect the Red wire to the accessory wire.

Connections to be made

NITO-01

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the NITO-01 harness, into

the interface.

• Connect the NITO-01 harness to the wiring harness in the vehicle.

Note: If using the ASWC-1, connect it after you initialize and test the NITO-01,

with the key in the off position.

Attention! If the interface loses power for any reason, the following steps will need

to be performed again. Also, if installing an ASWC-1 connect it after you initialize

and test the interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the

radio comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the

off position, disconnect the interface, check all connections, reconnect the

interface, and then try again.

• Turn the key to the off position, and then to the accessory position. Test all

functions of the installation for proper operation.

•

Refer to “Adjusting the NITO-01”, and “Extra Settings” before reassembling the dash

Audio level adjustment:

• With the vehicle and radio turned on, turn the volume up 3/4 of the way.

• With a small flat-blade screwdriver, adjust the potentiometer clockwise to raise

the audio level; counterclockwise to lower the audio level.

• Once at the desired level, audio level adjustment is complete.

Audible parking sensor warning level adjustment:

• Put the vehicles gear selector in reverse and keep your foot firmly on the brake

pedal during this entire process.

Note: Do not activate the emergency brake, this will prohibit the audible parking

sensors from working.

• Have a helper walk near the rear of the vehicle to activate the parking sensors,

close enough so that the audible parking sensor warning will produce a

constant signal.

• With a small flat-blade screwdriver, adjust the potentiometer clockwise to raise

the audible parking sensor warning level; counterclockwise to lower the audible

parking sensor warning level.

• Once at the desired level, the audible parking sensor warning level adjustment

is complete. Put the vehicles gear selector back into park.

Initializing the NITO-01

Adjusting the NITO-01Installing the NITO-01

Especificaciones del producto

Marca:	Metra
Categoría:	No categorizado
Modelo:	NITO-01

¿Necesitas ayuda?

Si necesitas ayuda con Metra NITO-01 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado Metra Manuales

Metra 71-017C Manual de Usario

26 Septiembre 2024

Metra AXSP-HK Manual de Usario

26 Septiembre 2024

Metra 109-TO7 Manual de Usario

24 Septiembre 2024

Metra 95-8273B Manual de Usario

19 Septiembre 2024

Metra 95-7822 Manual de Usario

19 Septiembre 2024

Metra 82-8703 Manual de Usario

19 Septiembre 2024

Metra 88-00-9004 Manual de Usario

19 Septiembre 2024

Metra 82-9101 Manual de Usario

19 Septiembre 2024

Metra 95-7021HG Manual de Usario

19 Septiembre 2024

Metra 82-5608 Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024