Metra XSVI-9005-NAV Manual de Usario

Metra No categorizado XSVI-9005-NAV

Lee a continuación 📖 el manual en español para Metra XSVI-9005-NAV (1 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/1

INSTXSVI-9005-NAV

1-800-221-0932 metraonline.com

INSTXSVI-9005-NAV

1-800-221-0932 metraonline.com

Connections to be made

• Connect the Yellow wire to the radio’s 12-volt battery or memory wire.

• Connect the Black wire to the radio’s ground wire.

• Connect the Red wire to the ignition wire of the aftermarket radio.

• Connect the Orange wire to the illumination wire of the aftermarket radio. If the

aftermarket radio has no illumination wire, tape off the wire.Orange

XSVI-9005-NAV

Mercedes accessory and NAV output CAN

Interface 2005-up

APPLICATIONS

FREIGHTLINER

Sprinter 2014-up

MERCEDES

C Class 2005-2011

CLK Class 2005-2009

E Class 2010-up

G Class 2007-2012

GLK Class 2010-2012

R Class 2006-2011

SLK Class 2005-2011

Sprinter 2010-up

FEATURES

• Provides accessory (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Used in non-amplified systems, or when replacing amplified system

• Provides NAV outputs (parking brake, reverse, and V.S.S.)

• Prewired ASWC-1 harness included (ASWC-1 sold separately)

• High level speaker input

• USB updatable

Caution: Metra recommends disconnecting the negative battery terminal before beginning

any installation. All accessories, switches, and especially air bag indicator lights must be

plugged in before reconnecting the battery or cycling the ignition.

*Note: Refer also to the instructions included with the aftermarket radio.

• Connect the Blue wire to the antenna turn on wire of the

aftermarket radio.

• Connect the White wire to the left front positive speaker output of the

aftermarket radio.

• Connect the White/Black wire to the left front negative speaker output of the

aftermarket radio.

• Connect the Gray wire to the right front positive speaker output of the

aftermarket radio.

• Connect the Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the Green wire to the radio’s left rear positive speaker output.

• Connect the Green/Black wire to the radio’s left rear negative speaker output.

• Connect the Purple wire to the radio’s right rear positive speaker output.

• Connect the Purple/Black wire to the radio’s right rear negative speaker output.

The following wires are for the aftermarket radios that have navigation built in.

• Connect the Light Green wire to the parking brake wire of the aftermarket

navigation radio (if applicable).

• Connect the Blue/Pink wire to the VSS or speed sense wire of the aftermarket

navigation radio (if applicable).

• Connect the Green/Purple wire to the reverse wire of the aftermarket navigation

radio (if applicable).

• Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to

test the radio.

ASWC-1 (if installing)

After the XSVI is initialized, plug in the ASWC-1 into the 12-pin harness of the

XSVI-9005-NAV and refer to the ASWC-1 instructions.

K PNOWLEDGE IS OWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certiﬁed technicians

Especificaciones del producto

Marca:	Metra
Categoría:	No categorizado
Modelo:	XSVI-9005-NAV
Color del producto:	Wit
Peso.:	300 g
Ancho:	124 mm
Profundidad:	196 mm
Altura:	144 mm
Peso del embalaje:	360 g
Ancho del embalaje:	168 mm
Empaquetadura en profundidad:	250 mm
Altura del embalaje:	62 mm
Amable:	GPU-kit
Cantidad por paquete:	1 stuk(s)
Versión de ranuras PCI Express:	4.0
Soporte PCI Express:	1
Productos compatibles:	North, Focus 2, Define 7, Meshify 2, Torrent
Incluyendo tornillos:	Ja
Tipo de chasis compatible:	Universeel
Cable plano (ascendente) incluido:	Ja
Longitud del cable de banda (ascendente):	195 mm
Número de tarjetas gráficas admitidas:	1 stuk(s)