Microchip EVB-USB2507 Manual de Usario

Microchip No categorizado EVB-USB2507

Lee a continuación 📖 el manual en español para Microchip EVB-USB2507 (4 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

SMSC EVB-USB2507 Revision A1(06-26-07)

The information contained herein is proprietary to SMSC and shall be used solely in accordance with the agreement pursuant to which

it is provided. Although the information is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the

right to make changes to this document and to specifications and product descriptions at any time without notice. Neither the provision

of this information nor the sale of the described semiconductor devices conveys any licenses under any patent rights or other intellectual

property rights of SMSC or others unless specifically specified otherwise. The product may contain design defects or errors known as

anomalies, including but not necessarily limited to any which may be identified in this document, which may cause the product to deviate

from published specifications. SMSC products are not designed, intended, authorized or warranted for use in any life support or other

application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without

prior written approval of an officer of SMSC will be fully at the risk of the customer. SMSC is a registered trademark of Standard

Microsystems Corporation ("SMSC").

SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE,

AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE

LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA,

PROFITS, SAVINGS OR REV-ENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT;

NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY

OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

EVB-USB2507 Evaluation Board

Revision A1(06-26-07) SMSC EVB-USB2507

1 Overview

1.1 Features

Operates from a single voltage (+5.0V, regulated) wall wart external power supply

Onboard +3.3V Regulator

Self-powered operation

Serial EEPROM for configuration information mounted in a socket

Header for SMBUS connection

Full set of green and amber LED indicators

Individual port over-current sense and power switching

Multi-TT enabled

High-speed/Full-speed capable

100mS down stream port power on time

1mA VBUS current consumption

1.2 General Description

The primary purpose of this board is to demonstrate a full-featured HUB configuration for the SMSC

USB2507 7-port HUB. This does not represent a minimal cost design. The EEPROM allows for

modifications to the base configuration - for example one or more down stream ports can be disabled

or configured as non-removable for compound device application. The DID, PID or DID information

can be changed for the HUB. The top silk screen of the evaluation board is shown in figure 1.

The EVB-USB2507Q board can be configured via EEPROM or from an external SMBus master. If an

external SMBus master is available it can be connected to header J1. Table 1 shows the jumper

settings to select SMBus or EEPROM. Note that internal default is not supported on this board.

The EVB-USB2507Q can configure the hub to report as self-powered or bus-powered. Table 2shows

the jumper selection.

The board itself does not support true bus power mode. The external power supply must be connected

for the board to operate.

A Windows utility E2PROMAPP is included in the package to allow modifications of the base

configuration EEPROM. The bin file evb-usb2507_01.bin contains the base configuration. A screen

shot from the application is shown in figure 2. After changes has been selected click the button "Create

EEPROM File". Note that if the output file name is put file name it the same as the in will be overwritten

with the new values. The output file name can be changed before creating a new bin file. The bin file

format is compatible with most EEPROM programmers.

EVB-USB2507 Evaluation Board

SMSC EVB-USB2507 Revision A1(06-26-07)

Figure 1.1 Top Silk Screen of EVB-USB2507Q

Table 1 Configuration Source

CONFIGURATION CFG_SEL1 CFG_SEL0

SMBus Configuration

(SMBUS connects to J1)

J4 shunt 3-5 (0) Don’t care

Internal default with

strapping options

J4 shunt 1-3 (1) J1 shunt 3-4 (0)

EEPROM configuration J4 shunt 1-3 (1) J1 open 3-4 (1)

Table 2 Self/Bus Powered Operation

MODE SELF_PWR

Bus Powered Operation J4 shunt 4-6 (0)

Self Powered Operation J4 shunt 2-6 (1)

Especificaciones del producto

Marca:	Microchip
Categoría:	No categorizado
Modelo:	EVB-USB2507
Tipo de operación:	Knoppen
Color del producto:	Roestvrijstaal
Ancho:	600 mm
Profundidad:	500 mm
Nivel de ruido:	58 dB
Clase-de-eficiencia-energética:	C
Consumo-anual-de-energía:	61 kWu
Amable:	Plafond inbouw
Diámetro de la conexión de escape:	150 mm
Motor incluido:	Ja
Número de motores:	1
Capacidad máxima de extracción:	700 m³/uur
Método de extracción:	Luchtafvoer
Clase de eficiencia fluidodinámica:	D
Clase de eficiencia lumínica:	A
Clase de eficiencia del filtro de grasa:	B
Distancia mínima a la placa eléctrica:	650 mm
Distancia mínima a la encimera de gas:	650 mm
Número de lámparas:	2 gloeilamp(en)
Tipo de lámpara:	LED
Tipo filtro veterinario:	Metaal
Altura (mín.):	765 mm
Altura (máx.):	1020 mm
Nivel de ruido (alta velocidad:	65 dB
Número de filtros:	1 stuk(s)
Número de velocidades:	3
Apagado automático:	Ja
modo intensivo:	Ja