Microchip MIC4811YMM Manual de Usario

Lee a continuación 📖 el manual en español para Microchip MIC4811YMM (4 páginas) en la categoría No categorizado. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
MIC4811 Evaluation Board
High Current 6 Channel Linear WLED
Driver with DAM™ and Ultra Fast
PWM™ Control
Ultra Fast PWM and DAM™ Dynamic Average Matching are trademarks of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 http://www.micrel.com
General Description
The MIC4811 is a high efficiency linear White LED
(WLED) driver; it is designed to drive up to six high current
WLEDs while maintaining constant current in each
channel. The MIC4811 features Dynamic Average
Matching (DAM™) which is specifically designed to
provide optimum matching across all WLEDs. These high
accuracy (±1% typical) current regulated WLED channels
ensure uniform display illumination under all conditions. A
typical dropout of 100mV at 50mA is expected.
The MIC4811 is available in a 10-pin MSOP package with
a junction temperature range of -40°C to +125°C.
Datasheets and support documentation can be found on
Micrel’s web site at: www.micrel.com
Requirements
The MIC4811 evaluation board requires a power supply
that is capable of delivering at least 1A while providing an
input voltage between 3.0V and 5.5V.
Precautions
The MIC4811 evaluation board is designed for an input
voltage no greater than 6V. This evaluation board does not
have reverse polarity protection; hence, applying a
negative voltage to the VIN terminal may damage the
device.
Getting Started
1. Connect an external supply to VIN. Apply the
desired input voltage across VIN and ground
terminals, J1 and J2, respectively, paying careful
attention to polarity and supply voltage
(3.0VVIN5.5V). An ammeter may be placed
between the input supply and the VIN terminal to
the evaluation board. Ensure that the supply
voltage is monitored at the VIN terminal. The
ammeter and/or power lead resistance can reduce
the voltage supplied to the input.
2. Enable/Disable the MIC4811
To enable the device, apply a DC voltage of 1.2V or
greater to the EN pin (J3). This allows for full
brightness of the WLEDs (100% duty cycle). The EN
pin can also be used for dimming by connecting a
PWM signal and varying its duty cycle (please refer to
the Ultra Fast PWM™ Dimming Interface Section in
datasheet). Pulling EN low for more than 20ms forces
the MIC4811 into a low IQ sleep mode. Do not leave
the EN pin floating as this may cause an indeterminate
output state. A pull down resistor of 200k is placed from
EN to GND to ensure that the WLEDs are OFF when an
enable signal is not applied.
3. Setting LED current with RSET resistor.
The average LED current may be calculated using the
equation below:
( )
139.0)(
820
)(
139.0
)(
820
)(
Ω
=
+
=Ω
kR
D
mAI
mAI
D
kR
SET
LED
LED
SET
D is the duty cycle of the LED current during PWM
dimming; D=1 when device is fully ON. The stock
evaluation board uses an RSET value of 16.5k which
corresponds to ILED of 50mA.
4. Measuring WLED current.
To measure WLED current, simply insert an ammeter
in series with the WLED(s). Keep in mind that a series
ammeter will add a small voltage drop, so the voltage
at the WLED terminal(s), D1-D6, should be used when
making dropout measurements with a series ammeter.
Ordering Information
Part Number Description
MIC4811YMM EV Evaluation board with Six Channel
WLED Driver
March 2011 M9999-032111-B
Micrel, Inc. MIC4811 Evaluation Board
March 2011 2 M9999-032111-B
MIC4811 Evaluation Board Schematic
Bill of Materials
Item Part Number Manufacturer Description Qty
C1608X5R0J225K TDK(1)
06036D225KAT2A AVX(2)
GRM188R60J225KE
19D
Murata(3)
C1
VJ0603G225KXYAT Vishay(4)
Ceramic Capacitor, 2.2µF, 6.3V, X5R, Size 0603 1
LED1– LED6 OVS5WBCR4 OPTEK Technology, Inc
(5) WLED 6
R1 CRCW060316K55F5
EA
Vishay(4) Resistor, 16.5, 1%, 1/16W, Size 0603 1
R2
CRCW06032003FKE
A Vishay(4) Resistor, 200k, 1%, 1/16W, Size 0603 1
U1 MIC4811YMM Micrel, Inc.(6) High Current 6 Channel Linear WLED Driver
with DAM™ and Ultra Fast PWM™ Control 1
Notes:
1. TDK: www.tdk.com
2. AVX: www.avx.com
3. Murata: www.murata.com
4. Vishay: www.vishay.com
5. OPTEK: www.optekinc.com
6. Micrel, Inc.: www.micrel.com
Micrel, Inc. MIC4811 Evaluation Board
March 2011 3 M9999-032111-B
PCB Layout Recommendations
Top Layer
Bottom Layer

Especificaciones del producto

Marca: Microchip
Categoría: No categorizado
Modelo: MIC4811YMM

¿Necesitas ayuda?

Si necesitas ayuda con Microchip MIC4811YMM haz una pregunta a continuación y otros usuarios te responderán




No categorizado Microchip Manuales

No categorizado Manuales

Últimos No categorizado Manuales