Microchip MIC5375/6 Manual de Usario

Lee a continuación 📖 el manual en español para Microchip MIC5375/6 (6 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/6
MIC5375/6 Evaluation Board
High Performance Low Dropout
150mA LDO
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
January 2009 M9999-012109-A
General Description
The MIC5375/6 is a low quiescent current, low dropout
regulator designed for optimal performance in a small
space. When the MIC5376 is disabled an internal resistive
load is automatically applied to the output to discharge the
output capacitor. The MIC5375/6 is capable of sourcing
150mA of output current while only consuming 29µA of
operating current. This high performance LDO offers fast
transient response and good PSRR while consuming a
minimum of current.
Ideal for battery operated applications; the MIC5375/6
offers low dropout voltage 120mV typically @ 150mA. The
MIC5375/6 can also be put into a zero-off-mode current
state, drawing virtually no current when disabled.
An input capacitor may be required when the power supply
is more than 4-inches from the device. The evaluation
board includes an input capacitor of 10μF to compensate
for long inductive test leads.
Requirements
The MIC5375/6 evaluation board requires an input power
supply of 400mA with a voltage range of 2.3V to 5.5V to
the VIN.
Precautions
The evaluation board does not have reverse polarity
protection. Applying a negative voltage to the VIN terminal
may damage the device.
Getting Started
1. Connect an external supply to VIN. Apply desired
input voltage to the VIN (J1) and ground terminal
(J2) of the evaluation board, paying careful
attention to polarity and supply voltage. An
ammeter may be placed between the input supply
and the VIN terminal to the evaluation board.
Ammeter and/or power lead resistance can reduce
the voltage supplied to the input.
Ensure that the supply voltage is monitored at VIN
terminal. There is 10uF capacitor connected from
VIN (J1) to GND (J2).
2. Enable/Disable the MIC5375/6. The YMT (1x1
TMLF) evaluation board is provided with a 100k
pull up resistor on enable pin (EN) to VIN, where as
the YC5 (SC-70) evaluation board is provided with
a 100k pull down resistor from the enable pin
(EN) to GND. Simply jumper the enable pin (EN)
to VIN to enable the regulator output, or to GND to
disable the output. The enable pin must be either
pulled high or low. Removing the pull up resistor
and leaving the EN pin floating will cause the
regulator to operate in an indeterminate state.
3. Connect the loads to the VOUT terminal (J3) and
ground terminal (J2). The load can be either a
passive (resistor) or active (electronic load). Be
sure to monitor the output voltage at the VOUT (J3)
terminals. The evaluation board has a 1uF
capacitor connected from VOUT (J3) to GND (J2).
Ordering Information
Part Number Description
MIC5375-2.8YMT High Performance Low Dropout 150mA LDO,
1x1 TMLF,VOUT = 2.8V Evaluation Board
MIC5375-2.8YC5 High Performance Low Dropout 150mA LDO,
SC-70, VOUT = 2.8V Evaluation Board
MIC5376-2.8YMT High Performance Low Dropout 150mA LDO,
1x1 TMLF, VOUT = 2.8V Evaluation Board
MIC5376-2.8YC5 High Performance Low Dropout 150mA LDO,
SC-70,VOUT = 2.8V Evaluation Board
Micrel, Inc. MIC5375/6 Evaluation Board
January 2009 2 M9999-012109-A
Evaluation Board Schematic
VIN VOUT
EN
U1 MIC5375/6-xxYMT
GND C2
1µF
10V
J3
VOUT
J4
GND
C1
10µF
6.3V
4
2 3
1
R1
100k
J1
VIN
J2
GND
J5
EN
Bill of Materials
Item Part Number Manufacturer Description Qty.
GRM155R61A105KE15D Murata(1)
C1005X5R1A105KT TDK(2)
C2
CV05X5R105K10AH AVX/Kyocera(3)
Capacitor, 1µF Ceramic, 10V, X5R, Size 0402 2
C1 C1608X5R0J106Z TDK(2) Capacitor, 10µF Ceramic, 6.3V, X5R, Size 0603
R1 CRCW0603100KFKEA Vishay(4) Resistor, 100k, 1%, 1/16W, Size 0603 1
U1 MIC5375/6-xxYMT Micrel, Inc.(5) High Performance 150mA LDO, 4-Pin 1mm x 1mm
Thin MLF®
1
Notes:
1. Murata: www.murata.com
2. TDK: www.tdk.com
3. AVX/Kyocera: www.avx.com
4. Vishay: www.vishay.com
5. Micrel, Inc.: www.micrel.com
Micrel, Inc. MIC5375/6 Evaluation Board
January 2009 3 M9999-012109-A
VIN VOUT
NC
GND
U1 MIC5375/6YC5
EN
C2*
2.2µF
6.3V
J3
VOUT
J4
GND
C1*
2.2µF
6.3V
1
3
2
4
5
R3
100k
J1
VIN
J5
EN
J2
GND
Bill of Materials
Item Part Number Manufacturer Description Qty.
JMK105BJ225MV-F Taiyo Yuden(1)
GRM155R60G225ME15D Murata(2) C1, C2
CV05X5R225K10AB AVX/Kyocera
(3)
Capacitor, 2.2µF, 6.3V, X5R, Size 0402 2
GRM155R61A105KE15D Murata(1)
C1005X5R1A105KT TDK(2)
C1, C2
CV05X5R105K10AH AVX/Kyocera
(3)
Capacitor, 1µF Ceramic, 10V, X5R, Size 0402 2
R1 CRCW0402619KFKEA Vishay(4) Resistor, 619k, 1%, 1/16W, Size 0402 1
R2 CRCW04022673KFKEA Vishay(4) Resistor, 267k, 1%, 1/16W, Size 0402 1
R3 CRCW04021003KFKEA Vishay(4) Resistor, 100k, 1%, 1/16W, Size 0402 1
U1 MIC5375/6YC5 Micrel, Inc.(5) High Performance 150mA LDO, 5-Pin SC-70 1
Notes:
1. Taiyo Yuden:
2. Murata: www.murata.com
3. AVX/Kyocera: www.avx.com
4. Vishay: www.vishay.com
5. Micrel, Inc.: www.micrel.com
* CIN = COUT = 1µF for Vout 2.5V, CIN = COUT = 2.2µF for VOUT < 2.5V

Especificaciones del producto

Marca: Microchip
Categoría: No categorizado
Modelo: MIC5375/6

¿Necesitas ayuda?

Si necesitas ayuda con Microchip MIC5375/6 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Microchip Manuales

No categorizado Manuales

Últimos No categorizado Manuales