Milwaukee M18 Fuel 2903-22 Manual de Usario
Milwaukee
taladradora
M18 Fuel 2903-22
Lee a continuación 📖 el manual en español para Milwaukee M18 Fuel 2903-22 (11 páginas) en la categoría taladradora. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/11
Cat. No. / No de cat.
2903-20, 2904-20
M18 FUEL™ 1/2" DRILL/DRIVER AND HAMMER DRILL/DRIVER
PERCEUSE-VISSEUSE ET PERCEUSE À PERCUSSION DE
M18 FUEL™ 13 mm (1/2")
TALADRO DESTORNILLADOR Y TALADRO DE PERCUSIÓN
DE 13 mm (1/2") M18 FUEL™
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not
turn it on and o. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may aect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations dierent from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins
4
2. To remove the side handle, loosen the side handle
grip until the side handle can be removed. Reposi-
tion and tighten securely.
Correct Incorrect
WARNING
Always remove battery pack before
changing or removing accesso-
ries. Only use accessories specically recom-
mended for this tool. Others may be hazardous.
Installing Bits
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To the chuck jaws, turn the sleeve in the open
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" o of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
2. To the chuck jaws, turn the sleeve in the close
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the counter-
clockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck’s operation.
OPERATION
WARNING
To reduce the risk of injury, always
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Selecting Drill or Drive Action
(Cat. No. 2903-20)
1 . To use the drilling mode, rotate
the torque selector collar until the
drill symbol appears in line
with the arrow.
2. To use the driving mode rotate
the torque selector collar until the
desired clutch setting appears in
line with the arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving
the screw too deep into dierent
materials and to prevent damage to the screw or
tool.
Selecting Hammer, Drill or Drive Action
(Cat. No. 2904-20 )
FUNCTIONAL DESCRIPTION
1. LED
2. AUTOSTOP™ light
3. Trigger
4. Keyless chuck
5. Torque selector collar
6. Speed selector
7. Side handle
3
4
56
8
1
7
9
10
8. Control switch
9. Handle
10. Belt hook
2
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always lock the trigger or remove
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always use a side
handle when using this tool. Always brace or
hold securely. Ensure side handle is tightened
securely before each use.
Installing the Side Handle
1. To install the side handle,
Hooks
Slots
loosen the side handle
grip until the hooks are far
enough apart to t into the
slots on the gear case
ring. Position the side
handle on the top, pointing
to the left or right. Tighten
the side handle grip until
it is secure.
Especificaciones del producto
| Marca: | Milwaukee |
| Categoría: | taladradora |
| Modelo: | M18 Fuel 2903-22 |
¿Necesitas ayuda?
Si necesitas ayuda con Milwaukee M18 Fuel 2903-22 haz una pregunta a continuación y otros usuarios te responderán
taladradora Milwaukee Manuales
8 Octubre 2024
1 Octubre 2024
30 Septiembre 2024
20 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
14 Septiembre 2024
taladradora Manuales
- taladradora Bosch
- taladradora AEG
- taladradora DeWalt
- taladradora Silverline
- taladradora Ferm
- taladradora Workzone
- taladradora Ozito
- taladradora Gude
- taladradora Makita
- taladradora Tryton
- taladradora Hitachi
- taladradora Black And Decker
- taladradora Vonroc
- taladradora Maestro
- taladradora Stanley
- taladradora Skil
- taladradora Yato
- taladradora Hilti
- taladradora Ryobi
- taladradora Festool
- taladradora Metabo
- taladradora Parkside
- taladradora Worx
- taladradora Meec Tools
- taladradora Hikoki
- taladradora Sun Joe
- taladradora Hazet
- taladradora Einhell
- taladradora Baumr-AG
- taladradora Maktec
- taladradora Bort
- taladradora Craftsman
- taladradora Malmbergs
- taladradora Power Craft
- taladradora Powerplus
- taladradora Porter-Cable
- taladradora Cotech
- taladradora Genesis
- taladradora Eibenstock
- taladradora Topcraft
- taladradora Scheppach
- taladradora Gamma
- taladradora Clas Ohlson
- taladradora Powerfix
- taladradora Carat
- taladradora Kress
- taladradora Bavaria
- taladradora Flex
- taladradora Berner
- taladradora Mafell
- taladradora Max
- taladradora Truper
- taladradora Bruder Mannesmann
- taladradora Powerblade
- taladradora Meister Craft
- taladradora Rupes
- taladradora Batavia
- taladradora Proxxon
- taladradora Protool
- taladradora Westfalia
- taladradora Economy
- taladradora Holzmann
- taladradora Fein
- taladradora Huvema
- taladradora Black Decker
- taladradora Stomer
- taladradora Elu
- taladradora Max Bahr
- taladradora Lux Tools
- taladradora Goon
- taladradora Wolfcraft
- taladradora Dedra
- taladradora Kreg
- taladradora Wurth
- taladradora Spit
- taladradora Global
- taladradora Profitech
- taladradora Graphite
- taladradora Rikon
- taladradora Duro Pro
- taladradora Baier
- taladradora Alpha Tools
- taladradora MSW
- taladradora Ribimex
- taladradora Robust
- taladradora Einhell Bavaria
- taladradora Ergotools Pattfield
- taladradora MyTool
- taladradora McKenzie
- taladradora G-Technology
- taladradora Rodcraft
- taladradora Bavaria By Einhell
- taladradora Handwerk
- taladradora Stalco
Últimos taladradora Manuales
27 Octubre 2024
24 Octubre 2024
23 Octubre 2024
21 Octubre 2024
19 Octubre 2024
19 Octubre 2024
19 Octubre 2024
18 Octubre 2024
16 Octubre 2024
16 Octubre 2024