Motorola MS350R Manual de Usario
Motorola
Walkie-talkies
MS350R
Lee a continuación 📖 el manual en español para Motorola MS350R (5 páginas) en la categoría Walkie-talkies. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/5
1MS350 Series
MS350 Series
KEM-ML36100-15
Safety and General Information
Important Information on Safe and Efficient Operation
Read This Information Before Using The Radio.
The information provided in this document supersedes the general
safety information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
This two-way radio contains a transmitter and a receiver. To
control your exposure and ensure compliance with the general
population/uncontrolled environment exposure limits, always
adhere to the following procedure:
• Transmit no more than 50% of the time.
• To receive calls, release the PTT button.
• To transmit (talk), press the Push to Talk (PTT) button.
Transmitting 50% of the time, or less, is important because the
radio generates measurable RF energy exposure only when
transmitting (in terms of measuring standards compliance).
Exposure to Radio Frequency Energy
This Motorola two-way radio complies with the following RF
energy exposure standards and guidelines:
• United States Federal Communications Commission, Code of
Federal Regulations; 47CFR part 2 sub-part J.
• American National Standards Institute (ANSI)/Institute of
Electrical and Electronic Engineers (IEEE) C95. 1-1992.
• Institute of Electrical and Electronics Engineers (IEEE) C95.
1-1999 Edition.
• International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
• Ministry of Health (Canada) Safety Code 6. Limits of Human
Exposure to Radiofrequency Electromagnetic Fields in the
Frequency Range from 3 KHz to 300 GHz, 1999.
• Australian Communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
To ensure optimal radio performance and make sure human
exposure to radio frequency electromagnetic energy is within
the guidelines set forth in the above standards, always adhere
to the following procedures.
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could
damage the radio and may violate FCC regulations.
Do NOT hold the antenna when the radio is “IN USE.” Holding
the antenna affects its effective range.
Body-Worn Operation
To maintain compliances with FCC guidelines if you wear a radio
on your body when transmitting always place the radio in a
Motorola-supplied or approved clip holder, holster, case or body
harness for this product. Use of non-Motorola-approved
accessories may exceed FCC guidelines.
If you do not use one of the Motorola-supplied or approved
body-worn accessories and are not using the radio held in the
normal use position, ensure the radio and its antenna are at
least 1 inch (2.5 cm) from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or
without an accessory cable, position the radio and its antenna
at least one inch (2.5 cm) from the body.
Approved Accessories
53724: Remote Speaker with Push-to-Talk Microphone
53725: Headset with Swivel Boom Microphone
53727: Ear bud with Push-to-Talk Microphone
53728: Flexible Ear Receiver
56320: Earpiece with Boom Microphone
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to
electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic
compatibility. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received,
including interference that may cause undesired operation.
Facilities
To avoid electromagnetic interference and/or compatibility
conflicts, turn off the radio in any facility where posted notices
instruct you to do so. Hospitals or health care facilities may be
using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off the radio when onboard an
aircraft. Any use of a radio must be in accordance with
applicable regulations per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends
that a minimum separation of 6 inches (15 cm) be maintained
between a handheld wireless radio and a pacemaker. These
recommendations are consistent with the independent research
by and recommendations of the U.S. Food and Drug
Administration.
People with pacemakers should:
• ALWAYS keep the radio more than 6 inches (15 cm) from
their pacemaker when the radio is turned ON.
• Not carry the radio in the breast pocket.
• Use the ear opposite the pacemaker to minimize the
potential for interference.
• Turn the radio OFF immediately if there is any reason to
suspect that interference is taking place.
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing
aids. In the event of such interference, you may want to consult
your hearing aid manufacturer to discuss alternatives.
Medical Devices – Other
If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately
shielded from RF energy. Your physician may be able to assist
you in obtaining this information.
For More Information
For further information, you may call Motorola at 1-800-638-5119,
e-mail us at giantintl@callcenter.com or visit us on the Internet
at www.motorola.com.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in
the area where you drive, and always obey them. If you do use
the radio while driving, please:
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call
if driving conditions so require.
The use of a two-way radio while engaged in activities requiring
concentration may cause distraction or otherwise impair your
ability to safely participate in such activities. Always use
technology safely.
Do not place a portable radio in the area over an air bag or in the
air bag deployment area. Air bags inflate with great force. If a
portable radio is placed in the air bag deployment area and the
air bag inflates, the radio may be propelled with great force and
cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off the radio prior to entering any area with a potentially
explosive atmosphere. Only radio types that are especially
qualified should be used in such areas as “Intrinsically Safe.”
Do not remove, install or charge batteries in such areas. Sparks
in a potentially explosive atmosphere can cause an explosion or
fire resulting in bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred
to above include fueling areas such as below decks on boats,
fuel or chemical transfer or storage facilities, areas where the air
contains chemicals or particles (such as grain, dust or metal
powders) and any other area where you would normally be
advised to turn off your vehicle engine. Areas with potentially
explosive atmospheres are often—but not always—posted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off
the radio when you are near electrical blasting caps, in a
blasting area, or in areas posted “Turn off two-way radios.”
Obey all signs and instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor
burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such
as burns if a conductive material—like jewelry, keys or beaded
chains— touch exposed terminals. The conductive material may
complete an electrical circuit (short circuit) and become quite hot.
Exercise care in handling any charged battery, particularly when
placing it inside a pocket, purse or other container with metal
objects.
Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
Battery Charger Safety Instructions:
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received
a sharp blow, or has been dropped or damaged in any way.
3. Never alter the AC cord or plug provided with the unit. If the
plug will not fit the outlet, have the proper outlet installed by
a qualified electrician. An improper condition can result in a
risk of electric shock.
4. To reduce the risk of damage to the cord or plug, pull the
plug rather than the cord when disconnecting the charger
from the AC receptacle.
5. To reduce the risk of electric shock, unplug the charger from
the outlet before attempting any maintenance or cleaning.
6. Use of an attachment not recommended or sold by Motorola
may result in a risk of fire, electric shock or personal injury.
7. Make sure the cord is located so it will not be stepped on,
tripped over or subjected to damage or stress.
8. An extension cord should not be used unless absolutely
necessary. Use of an improper extension cord could result in
a risk of a fire and/or electric shock. If an extension cord
must be used, make sure that:
• The pins on the plug of the extension cord are the same
number, size and shape as those on the plug of the
charger.
®
Two-Way Radio
User’s Guide
The MS350R is approved for use in the US only.
This radio floats with included NiMH battery.
It may not float with some AA batteries.
• The extension cord is properly wired and in good
condition.
• The extension cord size is 18 AWG for lengths up to 100
feet, and 16 AWG for lengths up to 150 feet.
9. The supply cord of the AC adaptor cannot be replaced. If the
cord is damaged, call customer service at 1-800-638-5119 or
e-mail us at giantintl@callcenter.com.
2MS350 Series
For a fax:
Contact the
Fax-0n-Demand
system
For mail service:
Call the FCC
Forms Hotline
If you have
questions about
the FCC License:
Call the FCC
1-202-418-0177 1-800-418-FORM
(3676)
1-888-CALL-FCC
(225-5322)
Display Screen Guide
Control Buttons
Getting Started
Waterproof
This radio is waterproof to IP-67 standards. It will withstand
submersion under up to 1 meter of water for up to 30 minutes.
The radio is resistant to water, rain, and splashes only when the
battery cover and headset accessory port are sealed. Open the
battery compartment door or headset port cover only when the
radio is dry. Use of a headset accessory should be in dry
environments only.
The charging base and AC adaptor are not waterproof. Do not
expose the charger to rain or snow. Charge the radios only in a
dry location. Do not place wet radios into the charging base.
Installing the Batteries
Radio floats with included NiMH battery. It may not float with
some AA batteries. Each radio can use either 1 NiMH
rechargeable battery pack or 3 AA alkaline batteries and beeps
when the batteries are low.
Installing NiMH Rechargeable Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door and open the cover.
3. Remove the NiMH battery pack from the clear plastic bag
(do not disassemble or unwrap the battery pack).
4. Insert the NiMH battery pack with the diagram facing you.
(The ribbon should be underneath the battery pack and
should wrap around the right side of the pack for easy
removal.)
5. Close the battery cover and tighten the retaining screw on
the battery door.
Installing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door and open the cover.
3. Insert the three AA alkaline batteries with + and - polarity as
shown inside. (The ribbon should be underneath the AA
alkaline batteries and should wrap around the right side of
the batteries.)
4. Close the battery cover and tighten the retaining screw on
the battery door.
Caution: Radio may not float with some AA batteries installed.
Radio Battery Meter
The radio battery icon shows the battery charge level, from
full to empty . When the radio has one segment left,
the radio chirps periodically or after releasing (Low Battery
Alert).
Removing the NiMH Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door to release the battery cover and
open the cover.
3. Remove the NiMH battery pack by pulling the ribbon
attached to the radio.
4. Close the battery cover and tighten the retaining screw on
the battery door.
Removing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door, release the battery cover and
open the cover.
3. Gently remove each alkaline battery by easing each battery out
individually.
4. Close the battery cover and tighten the retaining screw on
the battery door.
Notes
• Exercise care when removing NiMH or AA batteries. Do not
use sharp or conductive tools to remove either of these
batteries.
• Remove the batteries before storing the radio for extended
periods of time. Batteries corrode over time and may cause
permanent damage to the radio.
• The battery door must be tightly closed with the screw to
maintain the waterproof seal of the radio.
Using the Battery Charger (Optional Accessory)
The battery charger provides drop-in charging convenience for
NiMH batteries and can be placed on any flat surface, such as a
desk or workbench. Charge the NiMH battery overnight (at least
16 hours) before using it for the first time. After the initial charge,
an empty battery is fully charged within 14 hours.
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the AC power supply cord into the jack on the desk
stand.
3. Plug the AC power supply into a standard wall outlet.
4. With a radio facing forward, slide it into one of the charging
pockets.
5. When charging in the battery charger, the red light on the
charger base will glow continuously.
Notes
• The light will remain red after the NiMH battery pack is fully
charged.
• When moving between hot and cold temperatures, do not
charge the NiMH battery pack until the battery temperature
acclimates (usually about 20 minutes).
• For optimal battery life, remove the radio from the charger
within 16 hours. Do not store the radio while connected to
the charger.
• If the radio is kept on while charging, the charging time will be
extended.
• Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty .
Allow time for the battery to charge to 1 bar before
attempting to transmit a message.
• When the radio is wet from rain or snow, thoroughly dry the
surface before charging or removing the batteries.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to
release the catch.
2. Pull the belt clip away from the back of the radio.
Turning the Radio On and Off
In the ON position, the radio chirps and briefly shows all feature
icons available on the radio. The display screen then shows the
current channel, code and all features that are enabled.
Press and hold for 3 seconds to turn the radio on. Press and
hold for 3 seconds to turn the radio off.
Setting the Volume
Press and hold for 3 seconds, then press the or keys
until you reach a comfortable listening level.
The MS350 has 16 volume levels controlled by the keys.
1. Press to increase volume.
2. Press to decrease volume.
3. Hold or to rapidly increase volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the
same channel and Interference Eliminator Code.
1. To talk, press and hold .
2. When you are finished talking, release .
FCC Licensing Information
This Motorola radio operate s on General Mobile Radio Service
(GMRS) frequencies and is subject to the Rules and Regulations
of the Federal Communications Commission (FCC). The FCC
requires that all operators using GMRS frequencies obtain a
radio license before operating their equipment. To obtain the
FCC forms, please visit the FCC’s Web site at
wireless.fcc.gov/uls/index.htm?job=home to source form 605
and 159, which includes all the instructions you will need.
If you wish to have the document faxed or mailed, or if you have
questions, please use the following contact information:
Changes or modifications not expressly approved by Motorola
may void the user’s authority granted by the FCC to operate this
radio and should not be made. To comply with FCC requirements,
transmitter adjustments should be made only by or under the
supervision of a person certified as technically qualified to
perform transmitter maintenance and repairs in the private land
mobile and fixed services as certified by an organization
representative of the user of those services. Replacement of any
transmitter component (crystal, semiconductor, etc.) not
authorized by the FCC equipment authorization for this radio
could violate FCC rules.
Note:
Note:
Note:
Note: Note: Use of this radio outside the country where it was
intended to be distributed is subject to government regulations
and may be prohibited.
For maximum clarity, hold the radio two to three inches away
from your mouth and speak directly into the microphone. Do not
cover the microphone while talking.
Talk Range
This radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet
apart.
Power Boost
To boost the radio’s power up to high power, press the top portion
of the button when talking. If you know your party is close by,
you can conserve the battery’s energy by pushing the lower part
of the button to use less power.
Note:
Note:
Note:
Note:Note: If you are on an FRS only channel (see “Channels and
Frequencies” tables on overleaf for details) the radio will only use
low power when either portion of the is pressed.
Monitor Button
Use the Monitor function to check if a channel is currently in use
by others. For maximum range performance, the Monitor
function will also help you to hear signals that are weak.
To latch the Monitor function on, Press and hold for three
seconds. When an empty channel is located, you will hear
continuous static and noise on that channel.
To turn the Monitor function off, tap a second time or press .
Push to Talk Timeout Timer
To prevent accidental transmissions and save battery life, the
radio emits a continuous warning tone and stops transmitting if
you press for 60 continuous seconds.
Menu Options
There are 12 options you may set to your preferences. Each press
of the MENU key advances you to the next option setting. Press
the or keys to change the setting. The menu will
automatically close 5 seconds after the last press of any button.
After the last menu item, the radio exits MENU mode and returns
to operation of the radio. A press of the button while setting
any menu option will immediately save all your settings and return
to operation of the radio.
All MENU settings will revert back to the factory default values if the
battery is fully discharged or removed for more than 30 seconds.
Menus and Values
1. Channel (1-22 and 15R-22R)
2. Interference Eliminator Code (1-121 or OFF)
3. Call Tone (1-10 or OFF)
4. iVOX (ON/OFF)
5. VOX sensitivity (1-3)
6. QT Noise Filtering (ON/OFF)
7. VibraCall (ON/OFF)
8. Keypad Tones (ON/OFF)
9. Talk Confirmation Tone (ON/OFF)
10. Auto Power Off (30/60/90 minutes or OFF)
11. Repeater Channel Enable (ON/OFF)
12. Repeater Transmitted Interference Eliminator Code
Selecting the Channel
This radio has 22 simplex channels plus 8 repeater duplex
channels. Channels are shared by other radio users and channel
selection will vary based on your location. Select a channel that is
not being used from the 22 available simplex channels. Channels
8-14 are low power (FRS 0.5 watt). All other channels are GMRS.
When the radio is on a FRS 0.5 watt channel, displays. When
the radio is on a GMRS 1.5 watt channel, displays.
The 8 GMRS repeater duplex channels 15R – 22R are disabled
by default. See on overleaf in”Enabling Repeater Channels”
order to select a repeater channel.
See the tables on overleaf for“Channels and Frequencies”
details on channel frequencies.
1. Press . The current channel setting flashes.
2. Press or and select the channel.
3. Press to save the channel setting or to continue set up.
Selecting the Interference Eliminator Code
This radio has 121 Interference Eliminator Code settings. When a
channel is in use by 2 or more groups, this feature blocks the
reception of signals that do not carry the matching tone or code.
There are 121 privacy codes. 0 is the off position, no codes are
enabled, and all users of that channel will be heard.
Note: When you connect a headset, the radio is automatically
set to the last chosen sensitivity level.
QTNoise Filtering
The QTnoise-filtering feature helps to ensure uninterrupted
communication with other Motorola radios that have this
feature. This feature also filters out unwanted transmissions
from other radios. This is useful in places where there is
heavy radio traffic, such as amusement parks or ski resorts.
Note: QTnoise filtering is not available when the radio is
scanning.
To turn QTn oise filtering on or off:
1. Press until displays. The current setting On/Off
will flash.
2. Press or to turn noise filtering On or Off.
3. Press to confirm your selection or to continue
set up.
To transmit to a radio that has QTnoise filtering turned on:
1. Select the same channel and Interference Eliminator
Code as the other radio.
2. Press to send a call tone. This allows your voice to
pass through the QTnoise filter on the receiving radio.
3. Press and speak normally.
Note: If you skip step 2, the beginning of your message may
not be heard on the receiving radio. For a 30-second period,
starting after the last transmission, all transmissions
received on the selected channel and code will pass
through the QTnoise filter.
VibraCall
TM Alert
VibraCall T M is a vibrating alert that notifies that the radio is
receiving a message. This is useful in noisy environments. When
the alert is on, the radio vibrates once every 30 seconds when
you receive a message on the channel and code you set.
1. To turn vibrating alerts on, press until is displayed. The
current setting will flash.
2. Press or to change the setting to On/Off.
3. Press to set or to continue set up.
Keypad Tones
You may enable or disable the speaker key tones. You will hear
the key tone each time a button is pushed.
1. Press until appears. The current setting On/Off will flash.
2. Press either or to turn On or Off.
3. Press to confirm or to continue set up.
Note: When the key tone feature is off, the following are not disabled:
• Transmit timeout alert tone
• Call tone
• Low battery alert tone or
• The transmitted talk confirmation tone
Transmitting a Talk Confirmation Tone
You can set this radio to transmit a unique tone when you finish
transmitting. It is like saying “Roger” or “Over” to let others
know you are finished talking. Talk Confirmation Tone is disabled
in repeater mode on channels 15R-22R.
1. Press until the appears. The current setting On/Off
flashes.
2. Press or to turn On or Off.
3. Press to set or to continue setup.
Auto Power Off
Your radio will save power by automatically turning itself off if
unused after a predetermined amount of time.
1. Press until displays. The current setting (0, 30, 60 or 90)
will flash.
2. Press or to set the time to 30 minutes, 60 minutes or
90 minutes. When this feature is activated, the will remain
on the display.
3. When you exit the Menu mode, the timer will begin. If a
button is pressed, or if there is an incoming signal, the timer
will restart.
4. Press to confirm or to continue set up.
Enabling Repeater Channels
Use of a repeater can greatly increase the radio range and
coverage area. Repeater use must be coordinated with the
owner of the repeater. Be sure to understand and follow the
sharing and usage rules for each repeater system.
See the ”Interference Eliminator Tone / Code Values” table on
overleaf for details on tone frequencies and code values.
1 . Press until the code starts to flash.
2 . Press or to select the code.
3. Press to save the code setting or to continue set up.
You can set a different code for each channel using this
procedure. An extended press of or allows you to scroll
rapidly so you can quickly reach the code you want.
This menu setting for repeater channels 15R-22R is used for
receiving only. The value must match with the repeater output.
Many repeaters will require a value of 0 or OFF. The transmitted
code is set separately and is often required for repeater access.
See on overleaf for”Selecting the Repeater Access (TX) Code”
additional information.
Note: You must set the Interference Eliminator Code to 0 to
communicate with radios that do not have Interference
Eliminator Codes.
Setting and Transmitting Call Tones
This radio can transmit different call tones to other radios in your
group so you can alert them that you want to talk. The radio has
10 call tones from which to choose.
To set a call tone:
1 . Press until the current call tone setting flashes and
appears.
2 . Press or to change and hear the call tone.
3 . Press to set the new call tone or to continue set up.
To transmit your call tone to other radios set to the same
channel and Interference Eliminator Code as your radio,
press .
Note: Setting the call tone to 0 disables the call tone feature.
Hands-Free Use Without Accessories ( )
You can use the iVOX feature to transmit hands-free without the
need for any headset accessories. Once iVOX is turned on, the
radio detects your voice and transmits when you speak into the
internal microphone.
1. Press until appears on the display. The current
setting On/Off will flash.
2. Press or to select On or Off.
3. Press to set or to continue set up.
Hands-Free Use With Accessories ( )
You can transmit hands-free more reliably with the use of
optional headset accessories. Once VOX is turned on, the radio
detects your voice and transmits when you speak.
Many accessories (sold separately) are available for this radio. For
more information, visit our Web site at www.motorola.com or
shop.giantintl.com.
1. Turn the radio off and plug the VOX accessory into the
accessory port.
2. Turn the radio on. VOX shows on the display.
3. Adjust the volume appropriately by pressing or . Lower
the volume before placing the accessory on your head or in
your ear.
4. To turn off, simply remove accessory.
Notes:
• There is a short delay between the time you start talking and when
the radio transmits. There is a short delay before the transmission is
completed.
• The accessory port cover must be tightly in place to
maintain the water tight seal of the radio.
Setting the Sensitivity Level When in Mode
Adjusting the radio’s sensitivity level helps minimize the
possibility of unintended noises triggering a transmission and
helps the radio pick up soft voices.
1. Press until VOX and the level setting (1 - 3) appear on the
display.
2. Press or to select the sensitivity level.
3. Press to set or to continue set up.
3 = High Sensitivity for quiet environments
2 = Medium Sensitivity for most environments
1 = Low Sensitivity for noisy environments
Date : Jan 14, 2011
3MS350 Series
Especificaciones del producto
| Marca: | Motorola |
| Categoría: | Walkie-talkies |
| Modelo: | MS350R |
¿Necesitas ayuda?
Si necesitas ayuda con Motorola MS350R haz una pregunta a continuación y otros usuarios te responderán
Walkie-talkies Motorola Manuales
24 Septiembre 2024
17 Septiembre 2024
16 Septiembre 2024
14 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
10 Septiembre 2024
4 Agosto 2024
3 Agosto 2024
16 Julio 2024
Walkie-talkies Manuales
- Walkie-talkies Kenwood
- Walkie-talkies Topcom
- Walkie-talkies Albrecht
- Walkie-talkies Alecto
- Walkie-talkies Vertex Standard
- Walkie-talkies Silvercrest
- Walkie-talkies Nedis
- Walkie-talkies Tristar
- Walkie-talkies Sencor
- Walkie-talkies Denver
- Walkie-talkies President
- Walkie-talkies Cresta
- Walkie-talkies Midland
- Walkie-talkies GoGEN
- Walkie-talkies Marquant
- Walkie-talkies Binatone
- Walkie-talkies Olympia
- Walkie-talkies Audioline
- Walkie-talkies Uniden
- Walkie-talkies Yaesu
- Walkie-talkies Oricom
- Walkie-talkies Cobra
- Walkie-talkies Switel
- Walkie-talkies Esscom
- Walkie-talkies Icom
- Walkie-talkies Reer
- Walkie-talkies Simrad
- Walkie-talkies IMC Toys
- Walkie-talkies DeTeWe
- Walkie-talkies Oregon Scientific
- Walkie-talkies Dickie
- Walkie-talkies Baofeng
- Walkie-talkies MAAS
Últimos Walkie-talkies Manuales
17 Octubre 2024
14 Octubre 2024
14 Octubre 2024
13 Octubre 2024
11 Octubre 2024
5 Octubre 2024
30 Septiembre 2024
27 Septiembre 2024
22 Septiembre 2024
20 Septiembre 2024