Mtx Audio TRT8P Manual de Usario

Lee a continuación 📖 el manual en español para Mtx Audio TRT8P (24 páginas) en la categoría No categorizado. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/24
mtxaudio.eu facebook.com/MTXEuropetwitter.com/MTXEurope
TRT8P
20cm (8“) Class-D Powered Tube - 140W RMS - 420W Peak
Designed by MTX in Phoenix, AZ - USA
Left Right
Power
+12V REM GND
High Level
Input
EBC
Remote
Input
Gain
4V - 0,1V
Ch.1 Ch.2
Protection
Power
Owners Manual - MTX TRT8P
Thank You !
Thank you for purchasing an MTX Audio High-End amplifier. Proper installation matched with MTX speakers and subwoofers provide
superior sound and performance for endless hours of waking the neighbors, slammin’ your friends or flat out stomping wanna-be
players. Congrats and enjoy the ultimate audio experience with MTX !
Specifications :
Powered vented tube enclosure
Mono block class-D amplifier
Subwoofer : 20cm (8”)
Amplifier Max Power : 420W
Amplifier RMS Power : 140W
High and low level inputs
EBC (External Bass Control) remote included
Dimensions : 25,5x26x48cm
Power Terminal (+12V) : This is the main power input for the amplifier and must be connected directly to the positive terminal of the
vehicles battery for proper operation. Use caution when installing (+12V) power cable in the vehicle. Avoid running this cable parallel
with RCA cables, antennas, or other sensitive equipment due to massive currents that can induce noise into the audio system. It is
also very important to have a tight, secure connection for maximum performance. MTX recommends using a minimum of 6mm2 full
copper power wire with the MTX TRT8P.
Remote Terminal (REM) : The amplifier can be turned on by applying 12 volts to this terminal. Typically this voltage is supplied by a wire
from the source unit marked “remote or “power antenna.
Ground Terminal (GND) : A proper ground is required for your amplifier to operate at peak performance. A short ground cable the same
diameter as the power cable should be used to attach the ground terminal directly to the chassis of the vehicle. Always remove paint,
dirt or debris to expose bare metal where the ground will be attached.
Protection LED (Prot.) : When the amp is in thermal protection, the LED turns to red.
PowerOn LED (PWR.) : The LED illuminates red when the amp is switched on.
RCA Inputs (Input) : These RCA inputs are used with source units that have RCA or Line level outputs. (Source units need a minimum
level of 100mV output for proper operation of the amplifier). MTX recommends only high quality RCA cables to decrease the possibility
of radiated noise entering the system.
Gain Control (Gain) : The gain control matches the input sensitivity of the amplifier to the source unit being used.
The operating range varies from 100mv to 4V. Adjusting the gain:
1. Turn the gain control on the amplifier all the way down (counter clockwise).
2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.
3. Adjust the gain control on the amplifier until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The amplifier is now calibrated to the output of the source unit.
Speaker level inputs (High Level Input) : This input will allow the amplifier to operate from source units with speaker-level outputs.
Output speaker leads from the source unit should be tied directly to the wire harness provided with the amplifier.
Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplifier on and off.
Remote bass control port (EBC) : use this port to connect the optional MTX EBC. It alows you to control the output level siting at the
front of the car.
Control Panel on the Amplifier :
Installation & Mounting :
MTX recommends your new MTX TRT8P to be installed by an Authorized MTX retailer. Any deviation from specified installation instruc-
tions can cause serious damage to the amplifier, speakers and/or vehicles electrical system. Damage caused from improper installation
is NOT covered under warranty. Please verify all connections prior to turn on your system !
1. Disconnect the vehicle’s negative battery cable.
2. Determine the mounting place for your MTX TRT8P. Keep in mind there should be sufficient air flow for proper cooling.
3. Install a positive (+) power cable from the vehicle’s battery through the firewall using a grommet or firewall bushing to avoid cable
damage from sharp edges of the firewall. Run the cable through the interior of the vehicle and connect it to the amplifier (+12V)
terminal (1). Do Not connect to the battery at this time.
Note : Use only proper gauge wire for both positive and negative connections.
4. Install a circuit breaker or fuse within 20cm of the battery. This effectively lowers the risk of severe damage to you or your vehicle
in case of a short circuit or accident. Make sure the circuitbreaker is switched off or the fuse is taken out of the fuse holder untill all
connections are made. Now connect your positive power cable to the positive battery terminal of the battery.
5. Grounding - Locate a proper ground point on the vehicle’s chassis and remove all paint, dirt or debris to reveal a bare metal surface.
Attach the ground wire to that contact point. Connect the opposite end of the ground wire to the (GND) terminal on the amplifier (3).
6. Connect a remote turn-on wire from the source unit to amplifier remote terminal (2). If the source unit does not have a dedicated
Remote Turn-on lead, you may connect to the source unit’s Power Antenna lead.
7. Connecting signal cables to the amplifier : There are two ways to supply the signal to your MTX TRT8P.
• To get maximum performance, we suggest connecting a high quality RCA to the corresponding outputs at the source unit and inputs
of the amplifier.
If a source unit is being used without RCA outputs, use the included high-level amplifiers speaker terminals (8) using the right
gauge speaker wire.
8. Double check all previous installation steps, in particular, wiring and component connections. Once verified, reconnect the vehicle’s
negative battery cable, turn the circuit breaker on or place the fuse in the fuse holder.
Note : Gain Levels on the amplifier should be turned all the way down (counter clockwise) before proceeding with adjustments.
How To Stay Tuned :
https://www.facebook.com/MTXEurope
https://twitter.com/MTXEurope
http://www.mtxaudio.eu

Especificaciones del producto

Marca: Mtx Audio
Categoría: No categorizado
Modelo: TRT8P

¿Necesitas ayuda?

Si necesitas ayuda con Mtx Audio TRT8P haz una pregunta a continuación y otros usuarios te responderán




No categorizado Mtx Audio Manuales

No categorizado Manuales

Últimos No categorizado Manuales