Paasche D3000R Manual de Usario

Paasche No categorizado D3000R

Lee a continuación 📖 el manual en español para Paasche D3000R (2 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

INSTRUCTION Manual D3000R - 8/7/2017

WARNING: When a flammable liquid is sprayed, there may

be danger of fire or explosion especially in a closed room:

keep compressor at least 20 feet away from areas where

hazardous concentrations of flammable vapors are likely to

occur. Disconnect power before servicing.

ATTENTION: Lorsqu’un liquide inflammable est pulverise, il

peut y avoir danger d’incendie ou d’explosion, specialement

dans une piece fermee; garder le compresseur a au moins

20 pieds des endroits ou des concentrations dangereuses

de vapeurs inflammables sont susceptibles de se produire.

Debrancher avant toute maintenance.

Manufactured in China for Paasche

D3000R Air Compressor

1/5 HP, 120 Volts, 60 Hz,

Max Operating Pressure 20-40 PSI.

47 Db’s. Weight: 10 lbs (4.5 kg)

Features:

• Portable & Lightweight

• 3/4 Gallon Tank

• Low Noise Level

• Thermally Protected

• Steady Air Flow

• Regulator & Moisture Trap

• Auto Stop and Start

• 1/4” NPT Fittings

• Carrying Handles

Compressor Specs:

• Single Cylinder Piston

• 1/5 HP

• 110-120 Volt / 60 HZ

• 20-40 Working Pressure

(Depending on Airbrush)

• .25 CFM

• 10 lbs (4.5kg)

• Dim: 7.75”L x 5.5”W x 6.5”H

• 6 Foot Electric Cord

This compressor is both ETL & CE Listed

Operation Instructions:

1) Connect R-75 Regulator to compressor using

white plumbers tape included.

2) Use Plumbers tape on threads to seal any air

leaks when installing airbrush hose.

3) Plug compressor into grounded outlet

4) Turn on compressor

5) Lift Black Knob on top of Regulator to adjust air

pressure. Pull “up” on regulator knob, twist clockwise to

increase air pressure.

(Note: press down on airbrush trigger while adjusting air

pressure.)

When you have reached desired air pressure push

“down” on Black knob to lock in setting.

6) Ensure the working area is well ventilated

7) Compressor will run when your airbrush is

being triggered

R-75 Regulator and moisture

Trap Air Pressure Adjustment.

GENERAL & SAFETY INFORMATION

GENERAL INFORMATION

The maximum pressure of the compressor is 20-40 (6 Bar). The maximum operating pressure while spraying will vary depending on

size of fluid tip, needle and aircap. Example VL#3 - 40psi, TG#2 - 35psi.

THERMAL PROTECTOR

The motor of this compressor has a thermal overload protector. If the motor should overheat, the overload protector will shut off the

motor. If this should occur, unplug the compressor and allow the motor to cool (approx. 5 minutes) and restart compressor.

SEALING OF AIR HOSE

When attaching the female pipe thread fitting from your air hose to the compressor, it may be necessary to use a quality pipe thread

sealant or PTFE pipe thread tape on the threaded air outlet of the compressor. Failure to do so may cause an air leak and your

compressor will not shut off as it should. NOTE: This unit does not require any lubricants or oil. Applying oil to any part could result in

damage to the compressor. All bearings, including those in the motor, are grease packed.

AUTOMATIC SHUT-OFF FEATURE

This compressor has a built-in pressure switch that automatically shuts-off the compressor when the airbrush is not in use. The

compressor will automatically stop when the airbrush is not in use. It will immediately start again as soon as the air is allowed to flow

through the airbrush.

TANK:

If the compressor is used in a humid environment the tank can accumulate water over time. The tank can be drained using the drain

screw located at the bottom of the tank. Just unscrew to drain.

GROUNDING INSTRUCTIONS

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape

wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into

an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

EXTENSION CORDS – If it is necessary to use an extension cord, use a 3-wire extension cord that has a 3-blade grounding plug and

a 3-slot receptacle that will accept the plug on the product. Make certain your extension cord is in good condition. Make certain your

extension cord wire is not less than 16 gauge for 25 feet, 14 gauge for 50 feet and 12 gauge for 100 feet. An undersized cord will cause

a drop in line voltage resulting in loss of power and overheating. If in doubt, use the next heavier gauge. The smaller the gauge number,

the heavier the cord.

WARNINGS

• Only use 110-120 volt, 60 cycle power supply for this compressor.

• Before plugging in check to make sure compressor is in good condition.

• Only operate compressor in accordance with current safety regulations.

• Keep working area clean and uncluttered and make sure area is well ventilated. Never operate the compressor in the presence of

flammable liquids or gases.

• Compressor air can produce dust, dirt and loose particles it comes in contact with. To prevent possible injury always wear safety

goggles or glasses. Never point any nozzle or spray toward a person.

• The air compressor is powered by electricity. Like and electric device, If not used properly it can cause electric shock.

• Keep out of reach of children.

Suggested Accessories:

1) HFM manifolds. For multiple hose hook ups. Each hose attachment has an open close valve.

Available in 2, 3, 4, 6, 8 & 10 outlets.

2) Hose adapter. If you hose has a 1/8” NPT fitting get the HF-592. For the opposite get HF-116.

3) A-194 Airbrush Holder

4) AC-7 Airbrush Cleaning Brushes.

Paasche Airbrush Company

9511 58th Place Kenosha, 53144WI

Phone: 773 867-9191/

Website: paascheairbrush.com E-Mail: info@paascheairbrush.com

Especificaciones del producto

Marca:	Paasche
Categoría:	No categorizado
Modelo:	D3000R
Color del producto:	Zwart
Pantalla incorporada:	Nee
Peso.:	105 g
Ancho:	131.3 mm
Profundidad:	79.7 mm
Altura:	13.5 mm
Peso del embalaje:	150 g
Ancho del embalaje:	150 mm
Empaquetadura en profundidad:	90 mm
Altura del embalaje:	50 mm
Indicadores LED:	Ja
Tipo de embalaje:	Doos
Tipo de conector USB:	USB Type-C
Tipo de fuente de energía:	USB
Cables suministrados:	USB Type-a naar USB Type-C
Lector de tarjetas de memoria integrado:	Nee
País de origen:	China
Número de conexiones USB:	1
versión USB:	3.2 Gen 1 (3.1 Gen 1)
Material:	Aluminium
Conecta y reproduce:	Ja
Voltaje de entrada:	5 V
Soporta Windows:	Windows 10, Windows 7, Windows 8, Windows Vista
conexión USB:	Ja
Soporta el sistema operativo Mac:	Mac OS X 10.10 Yosemite, Mac OS X 10.11 El Capitan, Mac OS X 10.12 Sierra, Mac OS X 10.13 High Sierra, Mac OS X 10.14 Mojave, Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion, Mac OS X 10.8 Mountain Lion, Mac OS X 10.9 Mavericks
Compatibilidad con Mac:	Ja
Guía de Instalación Rápida:	Ja
Incluyendo tornillos:	Ja
Tamaño del disco de almacenamiento:	2.5 "
Capacidad máxima de almacenamiento:	1 TB
Interfaces de unidad de almacenamiento compatibles:	Serial ATA, Serial ATA II, Serial ATA III
Ratio de transferencia:	10 Gbit/s
Número de unidades de almacenamiento admitidas:	1
Tipo-producto:	HDD-behuizing
Código del Sistema Armonizado (SA):	84733080
Soporte UASP:	Ja
Incluye destornillador:	Ja