PAC APH-TY04 Manual de Usario

PAC No categorizado APH-TY04

Lee a continuación 📖 el manual en español para PAC APH-TY04 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
Speaker Connection Harness for Select
Toyota and Lexus Vehicles with Factory Ampliers
Equipped with a 10-Pin and 12-Pin Connector
APH-TY04
C
Page 1
Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V1
Date: 010419
Introduction and Features
The APH-TY04 simplies speaker wire connections when adding aftermarket ampliers. Aftermarket ampliers can
be easily added with no need to cut or modify a vehicle’s original wiring. Each pair of wires has been labeled with the
corresponding speaker name.
Wiring Overview
Installation Notes
1. It is always best to use a tone generator (PAC part number: TL-PTG2) to verify that the tables in this manual, and the labels
on the wires, match the wiring in your specic vehicle. This is important as there are instances where different trim levels of
the factory system may have the speaker outputs in different locations.
2. Any factory amplier connectors other than the 10-pin and 12-pin connectors used by the APH-TY04, must remain
connected to the factory amplier when using a PAC AmpPRO Interface. The PAC AmpPRO Interface will not operate
properly without them connected.
3. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It
is important to understand which speakers are equipped in your vehicle.
4. If you are leaving any of the factory speakers connected to the factory amplier, simply connect the speaker wires (color for
color) between the male and female connectors, for the speakers that will be powered by the factory amplier. For example:
If you want the rear speakers to be powered by the factory amplier, simply connect the Green, Green / Black, Purple and
Purple / Black wires from the male connector to the Green, Green / Black, Purple and Purple / Black wires from the female
connector.
5. For vehicles that lose audio output when there is no load on the speaker outputs of the factory amplier, PAC load resistors
will be required (PAC Part Number LR335 or LR475).
1. Locate the vehicle’s factory amplier and disconnect the 10-pin and 12-pin connectors.
2. Connect the APH-TY04 harnesses to the connectors that were disconnected in the previous step.
3. Connect the male connectors from the APH-TY04 to the amplier.
4. Connect the longer loose wires from the APH-TY04, to your aftermarket amplier outputs or passive crossovers, according
to the tables in this manual.
5. Insulate unused wires in the 10-pin and 12-pin connectors that plug into the factory amplier side of the APH-TY04.
Installation Steps
Insulate any unused wires
Blue / BlackBlue
Red
Gree Redn /
Yellow / Red
1
610
7
Re Blackd /
Brown
Gree Whiten /
Yello Bluew /
Brow Blackn /
APH-TY04-HAR 10P A
6
1
10
7
Yello Bluew /
Yello
w / Red
Gree Redn /
Red
Blue
Gree Whiten /
Brow Blackn /
Re Blackd /
Blue / k Blac
Brown
APH-TY04-HAR 10P
B
1
Blue / Black Subwoofer 2 -
7
Blue Subwoofer 2 +
2
Red / Black Subwoofer 1 -
8
Red Subwoofer 1 +
3
Brown / Black Speaker 3 -
4
Brown Speaker 3 +
5
Green / White Speaker 1 -
9
Green / Red Speaker 1 +
6
Yellow / Blue Speaker 2 -
10
Yellow / Red Speaker 2 +
Speaker 2
Subwoofer 2
Subwoofer 1
Speaker 3
Speaker 1
Pin Number Wire Color Wires Description Label
APH-TY04 10-Pin Connector
Connect to aftermarket amplier
output or passive crossover.
Speaker Connection Harness for Select
Toyota and Lexus Vehicles with Factory Ampliers
Equipped with a 10-Pin and 12-Pin Connector
APH-TY04
C
Page 2
Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V1
Date: 010419
Whit Rede /
Gray / Red
White
Green
Purple
White / Blue
Gra Bluey /
Whit Blacke /
Gree Blackn /
Gray / Black
Gray
Purple / Black
1
7
8
12
APH-TY04-HAR 12P A
White e/ Blu
Gra Bluey /
Whit Blacke /
Gree Blackn /
1
7
8
12
Gray / k Blac
Gray
Purple k/ Blac
Whit Rede /
Gray / Red
White
Green
Purple
APH-TY04-HAR 12P
B
Wiring Overview (cont.)
APH-TY04 12-Pin Connector
Insulate any unused wires
1
White / Blue Speaker 4 -
8
White / Red Speaker 4 +
2
Gray / Blue Speaker 5 -
9
Gray / Red Speaker 5 +
3
White / Black Front Left -
10
White Front Left +
4
Gray / Black Front Right -
5
Gray Front Right +
6
Green / Black Rear Left -
11
Green Rear Left +
7
Purple / Black Rear Right -
12
Purple Rear Right +
Front Left Speaker
Front Right Speaker
Rear Left Speaker
Rear Right Speaker
Pin Number Wire Color Wires Description Label
Speaker 4
Speaker 5
Connect to aftermarket amplier
output or passive crossover.

Especificaciones del producto

Marca: PAC
Categoría: No categorizado
Modelo: APH-TY04

¿Necesitas ayuda?

Si necesitas ayuda con PAC APH-TY04 haz una pregunta a continuación y otros usuarios te responderán




No categorizado PAC Manuales

PAC

PAC RP4-GM31 Manual de Usario

19 Septiembre 2024
PAC

PAC NU-GM51 Manual de Usario

19 Septiembre 2024
PAC

PAC NAV-1129 Manual de Usario

19 Septiembre 2024
PAC

PAC LP7-2R Manual de Usario

19 Septiembre 2024
PAC

PAC LP7-4 Manual de Usario

19 Septiembre 2024
PAC

PAC GMK367B Manual de Usario

19 Septiembre 2024
PAC

PAC CP1-FRD1 Manual de Usario

19 Septiembre 2024
PAC

PAC C2A-CHY5 Manual de Usario

19 Septiembre 2024
PAC

PAC NU-GM3 Manual de Usario

19 Septiembre 2024
PAC

PAC CP1-TSL1 Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales