PAC C2R-VW2 Manual de Usario

PAC No categorizado C2R-VW2

Lee a continuación 📖 el manual en español para PAC C2R-VW2 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com

03-16-10

Radio Replacement Interface

with Nav Outputs for select

Volkswagen CANbus Vehicles With

or Without Premium Audio Systems

C2R-VW2

1. Vehicles with or without a factory amplier: Connect the aftermarket radio’s

front and rear speaker wires to the 16 pin plug.

2. The accessory output wire is located on the 11 pin CAN INTERFACE harness

- connect this wire to the radio’s

accessory wire. The accessory wire

supplies +12v, 1 amp max when key is

in the accessory or ignition position (see

g. 1: If more current is needed).

3. 11 pin plug (to CAN INTERFACE):

White/Green - Steering Wheel Control (SWC) output.1.

Green - Connect this wire to the radio’s reverse input wire only.2.

Orange/White - Connect this wire to the radio’s Illumination input wire only.3.

Violet/White - Connect this wire to the radio’s VSS input wire only.4.

Red/White - Connect this wire to the radio’s parking brake input wire only. 5.

Please Note: The parking brake wire will output a neg (-) trigger at all times until the vehicle is moving at a

speed of approximately 3 mph or faster.

Note: Do not connect these wires to any circuit other than the aftermarket radio’s wire harness.

4. 11 pin plug (to SWC INTERFACE):

This is a quick connection to a radio specic SWC interface. No additional connections are necessary other than radio

control connections. Plug the radio specic SWC interface in to this connector and program the radio specic SWC

interface for version 2. Do not cut the loops. Refer to the SWC interface instruction manual for the radio specic control

function programming order.

Fig. 1

(using a SPDT relay)

85 86

87a

Ground

High Current 12v

(Fused)

12v Acc.

From

Interface

New High

Current Output

Diode 1N4005

or equivelant

23456

1011

Accessory Output

+12volts 1amp max.

9 1

23456

101

9 1

SWC Interface.

Program for Version 2

Radio Specific Steering

Wheel Control Interface

(Sold Separately)

Program SWC

Interface for Version 2.

CAN INTERFACE

Navigation outputs and

Amplifier Remote Input

See Chart for wire color

descriptions.

Radio Connections. See aside

Chart for color description.

Yellow Battery +12v

Black Ground

Blue Amp Turn On Input

White Front L + input

White / Black Front L - input

Grey Front R + input

Grey / Black Front R - input

Green Rear L + input

Green / Black Rear L - input

Purple Rear R + input

Purple / Black Rear R - input

Radio Connection Chart:

(Read the Installation Notes before making

connections to the provided radio harness)

CAN Interface Connection Chart:

Red Acc. Output (1 amp)

Red / White P.B. Output (-)

Purple / White VSS Output (Pulse)

Orange / White Illum. Output (+)

Green Reverse Output (+)

White / Green SWC Output

Page 1

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com

03-16-10

1. 2002-2005 vehicles (excludes Touareg) - Can map track up and down, and volume up and down.

2. 2006-2010 vehicles with Eight button SWC (excludes Touareg) - Can map volume up and down, phone button, and star

button without effecting the Multi Function Display (MFD). Arrow up and down can be mapped but will control MFD.

3. 2009-2010 vehicles with 12 button SWC (excludes Touareg) - Can map left side of steering wheel (volume up and down, track

left and right, phone, and mute buttons) without effecting MFD. Arrow up and down on right side can be mapped but will control

MFD.

4. 2004-2010 Touareg - Can only map volume up and down

5. Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brake and Illumination outputs. PLEASE

NOTE: The Parking Brake is speed based. The C2R-VW2 will automatically send a Parking Brake signal when going below 4

Mph. The signal will shut off when going above 4 Mph.

6. 2002-2005 Vehicles - The C2R-VW2 does not provide a Reverse output trigger. This signal is unavailable on the data bus.

You must be replacing a factory Double-DIN radio. If the vehicle came equipped with a Single-DIN radio, the C2R-VW2 is not

compatible.

7. 2004-2007 Touareg - Does not retain digital audio amplied system seen when the vehicles is equipped with factory navigation

radio

SWC Programming & Installation Notes

DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-VW2 be held liable for consequential damages sustained in

connection with the C2R-VW2. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume

obligation or liability in relation to the C2R-VW2 other than its replacement.

Page 2