PAC CAM-TY12 Manual de Usario

PAC No categorizado CAM-TY12

Lee a continuación 📖 el manual en español para PAC CAM-TY12 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
CAM-TY12
Reverse Camera T-Harness for
Select Toyota & Scion Vehicles
www.pac-audio.com
Rev. 01182016
©2015 Pacific Accessory Corporation
Pacific Accessory Corporation® | 866-931-8021 | support@pac-audio.com
Introduction & Features
Installation:
Illustration / Schematic
The CAM-TY12 is a reverse camera T-harness that gives the ability to e i t h e r add a reverse camera input for compatible
TOYOTA and SCION OEM touchscreen radios or retain the factory camera when replacing the factory radio. Simple plug and
play installation.
1. Disassemble dash and remove the radio.
2. Disconnect the 24 pin connector from the back of the factory radio (if equipped) and install the T-harness.
3. Connect the RCA from the aftermarket camera to the female RCA located in the T-harness
3. The OEM radio, when connected to this harness, will provide a +6v power output if needed. Most aftermarket cameras
require +12v for power, if your camera requires +12v then you will need to find a reliable source of +12 volt ACC power. If
not being used please insulate the pin located at the end of the red wire.
4. To function properly the camera must have power before the vehicle is placed into reverse, so using the reverse lamp as a
power source is not recommended for proper functionality.
5. Normally a reverse trigger is long as the camera has power when the vehicle is placed into provided by the vehicle manufacturer, as
reverse, the radio should automatically switch to the reverse camera. In the event that the radio does not automatically switch
to the reverse camera a +12v reverse signal will need to be added to Pin 2 of the 28 pin connector. See Fig 1.
When adding a reverse camera to an OEM radio:
When retaining the factory reverse camera with an aftermarket radio:
1. Connect the factory 24 pin camera harness to the T-harness.
2. Connect the male side of the RCA into the aftermarket radios reverse camera input.
3. Connect the loose black wire to chassis ground.
4. Insert the pin located on the end of the red wire into the pin 12 location in the 20 pin connector of the RP4.2-TY11. This
pin is located next to the red/white programmable +12v output. See Fig. 2. If an RP4.2-TY11 is not being used along with this
harness then the red wire will need to connect to +6v. This may require an adapter to step down the voltage from +12v to +6v.
Fig. 2
Fig. 1

Especificaciones del producto

Marca: PAC
Categoría: No categorizado
Modelo: CAM-TY12

¿Necesitas ayuda?

Si necesitas ayuda con PAC CAM-TY12 haz una pregunta a continuación y otros usuarios te responderán




No categorizado PAC Manuales

PAC

PAC RP4-GM31 Manual de Usario

19 Septiembre 2024
PAC

PAC NU-GM51 Manual de Usario

19 Septiembre 2024
PAC

PAC NAV-1129 Manual de Usario

19 Septiembre 2024
PAC

PAC LP7-2R Manual de Usario

19 Septiembre 2024
PAC

PAC LP7-4 Manual de Usario

19 Septiembre 2024
PAC

PAC GMK367B Manual de Usario

19 Septiembre 2024
PAC

PAC CP1-FRD1 Manual de Usario

19 Septiembre 2024
PAC

PAC C2A-CHY5 Manual de Usario

19 Septiembre 2024
PAC

PAC NU-GM3 Manual de Usario

19 Septiembre 2024
PAC

PAC CP1-TSL1 Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales