PAC OnStar OS-5 Manual de Usario

PAC No categorizado OnStar OS-5

Lee a continuación 📖 el manual en español para PAC OnStar OS-5 (4 páginas) en la categoría No categorizado. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Pacic Accessory Corporation

® | Ontario, Ca. 91761 | Ph. 866-931-8021 | technicalsupport@pac-audio.com

www.pac-audio.com

Rev. 052914

P ifi A C ti

Page 1

OS-5

Radio Replacement with Retention for General OnStar®

Motors Vehicles

Introduction & Features

Important Notes

Wiring Connection Chart

Illustration / Schematic

The OS-5 interface allows the replacement of a factory radio in select General Motors vehicles with 29-bit LAN radios.

Using this interface will retain factory features such as OnStar, warning chimes, Rear Seat Controls (RSC), factory XM

Radio and the BOSE amplier when the original radio is removed. The OS-5 also provides data bus driven outputs such

as retained accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and parking brake.

1. The OS-5 will retain the use of the factory XM receiver. Factory SWC or RSE controls must be present for use of this feature.

2. SWI interface must be used in conjunction for SWC retention.

3. RSC buttons that are identical to the SWC will mimic the SWC function for function.

Red / White Parking Brake

Output (-)

Purple / White Vehicle Speed

Output

Blue OnStar® Volume

Adjust

Blue / White Amp Turn On Input

Orange / White Illumination Output

(+)

Green Reverse Output (+)

Brown Loop Mute Loop - See

installation note 7.

Aftermarket Radio Connections

Yellow Battery +12v

Black Ground

Red Accessory Output

White Front L + input

White / Black Front L - input

Grey Front R + input

Grey / Black Front R - input

Green Rear L + input

Green / Black Rear L - input

Purple Rear R + input

Purple / Black Rear R - input

Wiring

Aftermarket

Radio

Connections

Vehicle

Connections

Sub, Center Channel

& Rear Camera

Connections

XM Audio

Connections

Connect to SWC

Interface. Program

for Version 2.

OS-RADPWRAUDIO

XM R

XM L

SWC Interface

Connections

P ifi A C ti

Pacic Accessory Corporation

® | Ontario, Ca. 91767 | Ph. 866-931-8021 | technicalsupport@pac-audio.com

www.pac-audio.com

P ifi A C ti

Rev. 052914

Page 2

OS-5

Radio Replacement with OnStar® R e t e n t i o n f o r G e n e r a l

Motors Vehicles

Installation Steps

1. Make all connections as described in the chart on page1.

2. Factory installed ampliers will determine the audio output connection. If the vehicle has a factory installed amplier use the factory

amplier audio location. If a factory installed amplier is not present use the non-amplied factory audio location.

3. If the vehicle is equipped with a Premium BOSE system, connect the subwoofer and center channel RCA inputs to the aftermarket radios.

If the aftermarket radio to be installed does not have a dedicated center channel or sub output do not use this cable. To ensure best sound

performance channel summing is not recommended. Use this cable according to the outputs that are available.

4. If the vehicle is equipped with a reverse camera and the aftermarket radio has a reverse camera input, connect the yellow RCA plug on the

brown connector to the aftermarket radios reverse camera input.

5. If the aftermarket radio is equipped with an auxiliary input and you wish to retain the factory XM tuner, plug the RCA connectors from the

interface into the radios auxiliary input.

6. Plug the CMX chime module in if necessary (If the vehicle chimes when the radio is removed the CMX is not necessary). PLEASE NOTE:

In order to get the best possible sound out of the CMX please mount it in a place free and clear of any obstructions, preferably as close as

possible to the bottom of the dash pointing down toward the oor of the vehicle.

7. The Mute loop (if not cut) will turn the accessory output off when an

OnStar® or Bluetooth call is made or received. If the aftermarket radio

has a mute input cut this loop and connect the inner brown wire (next to the blue/white wire) to the mute input.

OnStar Volume Adjustment for Vehicles w/o SWC

• If SWC buttons are not present a SPST switch (not included) can be

used to control the OnStar® audio level during an OnStar® connection.

• Connect the Blue wire in pin 6 to one side of a SPST normally open

momentary switch.

• The other side of the SPST switch will be connect to .12 volt constant

• When OnStar® is active pressing the switch will change the audio level

10 steps.

11 1

Level

Switch

blue

SPST N.O. switch (not included)

Connect to radio side 12 volt

constant wire

Blue wire

Wire insertion side view of

OS-5 RADPWRAUDIO

Connector

SWC Output Connector

• The OS-5 provides a SWC output connector attached to the

OS5-RADPWRAUDIO harness. For ease of installation, all necessary

connections for a SWI-X, ECL2, JACK, PS or RC have made for you.

• When using this SWC output connector the radio specic SWC

interface must be programmed for version 2 (refer to SWC interface

programming instructions for exact programming sequence).

• Both loops should also remain in tact.

• During steering wheel button assignment programming each button

should be pressed and held for 1 second after the SWC interface LED

goes out with the exception of the Speak button.

• The speak button should be pressed for less than 1 second and

released.

• Pressing the Speak button for longer than 1.5 SEC will activate

OnStar.

Connect to SWC

Interface. Program

for Version 2.

Connect to Radio

Specific SWC

Interface

Pacic Accessory Corporation

® | Ontario, Ca. 91761 | Ph. 866-931-8021 | technicalsupport@pac-audio.com

www.pac-audio.com

Rev. 052914

P ifi A C ti

Page 3

OS-5

Radio Replacement with Retention for General OnStar®

Motors Vehicles

Rear Seat Entertainment (RSE); If equipped

1. Vehicles equipped with an overhead screen only:

In this application the must be used in order to feed A/V into the factory screen from an aftermarket head unit (head GMRVD

unit must support A/V out). With the , A/V will be passed from the aftermarket head unit to the rear screen and audio GMRVD

can be heard through the headphones. The GMRVD will also pass the Auxiliary inputs on the rear of the center console to the

aftermarket head unit.

2. Vehicles equipped with an overhead screen AND headrest monitors:

In this application the headrest monitors will function independently from the overhead monitor. Neither video or audio

can be passed to or from the headrest monitors. The overhead monitor will function exactly as described in #1.

Using the Radios Dual Zone Source Using the Factory XM Radio Tuner

• Press the power button to turn the RSE Controls on. When

Radio is displayed on the RSE Controls, the aftermarket

radios rear speaker output will be heard through the

headphone jacks. Putting the aftermarket radio into dual

zone mode should change the output level of the rear

speakers to a xed level. This allows precise user

adjustment from the level knobs on the RSE Controls (refer

to aftermarket radio owners manual for model specic dual

zone operation).

• The seek arrows and PROG button will control the radio

as programmed by the SWC interface. These buttons are

mapped to the SWC buttons as stated above.

• Pressing the SRCE button will toggle between the Factory

XM tuner and the Radio as the RSE source. Pressing the

power button will turn the RSE Controls off as well as turning

the key off. The seek arrows and PROG button will continue

to operate as stated (with the exception of SRCE which has

no function) when the Rear Seat Controls are turned off.

• Press the power button to turn the RSE Controls on. If Radio

is displayed press the SRCE button to select factory XM

tuner mode. When XM followed by the channel number is

displayed factory XM tuner audio will be heard through the

headphone jacks.

• The Seek arrows will control the factory XM radio tuner and

select the desired station.

• The PROG button will scroll through Presets 1-6

• Pressing the SRCE button will toggle between the Factory

XM tuner and Radio as the RSE source. Pressing the power

button or turning the key off will turn off the RSE Controls.

• The factory XM tuner must remain serviced to take

advantage of this feature. Visit www.xmradio.com for a

complete up-to-date channel listing and service options.

• In order for the RSE controls to properly work the XM tuner,

the front XM controls must be set to off.

Turns the

Rear Seat

Controls On

or Off

Change between

Factory XM tuner

and Dual Zone

Radio Source

Scrolls through

Presets 1-6

Seek to the

Factory XM

Tuner Station

Seek to the

Factory XM

Tuner Station

Turns the

Rear Seat

Controls On

or Off

Change between

Factory XM tuner

and Dual Zone

Radio Source

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

and Bar Button)

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

Down Button)

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

Up Button)

Radio

Using Rear Seat Audio Controls

Especificaciones del producto

Marca:	PAC
Categoría:	No categorizado
Modelo:	OnStar OS-5

¿Necesitas ayuda?

Si necesitas ayuda con PAC OnStar OS-5 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado PAC Manuales

PAC RP4-GM31 Manual de Usario

19 Septiembre 2024

PAC NU-GM51 Manual de Usario

19 Septiembre 2024

PAC NAV-1129 Manual de Usario

19 Septiembre 2024

PAC LP7-2R Manual de Usario

19 Septiembre 2024

PAC LP7-4 Manual de Usario

19 Septiembre 2024

PAC GMK367B Manual de Usario

19 Septiembre 2024

PAC CP1-FRD1 Manual de Usario

19 Septiembre 2024

PAC C2A-CHY5 Manual de Usario

19 Septiembre 2024

PAC NU-GM3 Manual de Usario

19 Septiembre 2024

PAC CP1-TSL1 Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024