Philips SPP3211WA Manual de Usario

Philips No categorizado SPP3211WA

Lee a continuación 📖 el manual en español para Philips SPP3211WA (2 páginas) en la categoría No categorizado. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
I2006-12/06
Installation instructions
Power Connections
Your Philips surge protector should be plugged directly into a
properly grounded outlet. All connected equipment should be plugged
directly into your surge protector. Using any extension cord, adapters,
other grounding wires or electrical connections in conjunction with a
Philips surge protector will void all Philips warranties. (For longer cord
applications, use a Philips surge protector with a 10 or 12 foot power
cord.) All wires leading into the equipment, including telephone and
coaxial lines, must pass through an appropriate Philips surge protector.
Philips surge protectors use an indicator display light to alert you to your
surge system’s effectiveness. The “Protection Working” indicator light shows
“ON” when surge protection circuitry is functioning properly. If that light is
off, it indicates that your surge unit has reached capacity and is no longer able
to protect against surges. Some units also
have a “Ground” indicator light to show
you that the wall outlet is wired properly.
Phone/Fax/Modem Connections
Some Philips surge protector models
come with Solid State Phone/Fax/Modem
surge protection. Instead of running a
connection directly from your Phone/
Fax/Modem to the wall jack, you must
pass the connection through the protected
jacks on your surge protector.
• Connect your phone/fax/modem line
from your wall outlet to the “Input” jack
on the surge protector. Connect a phone
cord into the “Output” jack on the surge
protector, and connect the other end of
the phone cord to the phone/fax/modem
jack of the device you want to protect.
• To claim damage under the Connected
Equipment Warranty as a result of
telephone service line transients,
equipment must be properly connected
to a Philips surge protector which
offers telephone line protection, and
your telephone service equipment
must include a properly installed
and operating “primary protection”
device at the service entrance. (Such
devices are normally added during
telephone line installation.)
• If you fail to connect the phone/fax/
modem protection your connected
equipment will not be covered by the
Connected Equipment Warranty. Most
modem damage can be prevented
if you take the time to connect the
phone/fax/modem protection.
HANDBOOK
Choosing the right surge protector
Make sure you have the correct surge protector for your connected
equipment. Philips makes a full range of power products for almost every
type of electronic equipment. Power surges can occur on any line running
into your home or office. This includes AC power lines, telephone lines,
and coaxial lines. A properly installed surge protector will ensure protection
from the power surges that continually hit your electronic equipment. If your
connected equipment has connections through a telephone or coaxial line,
Philips strongly recommends that you purchase and properly connect your
equipment to a surge protector designed to protect those features. If you
receive a power surge through your phone or coaxial line, and your equipment
is not properly connected to a surge protector designed to protect those
surges, any problems that arise will not be remedied under the warranty.
This product, like all surge protectors, has a limited life. Even under
normal circumstances, and in the absence of defects, the product’s life will end
when the components providing surge protection exceed capacity and cease
to provide protection from surges and spikes. This surge device features an
internal protection that will disconnect the surge protective component at the
end of its useful life, but will maintain power to the load (connected equipment)
- now unprotected, thus, acting as a multiple outlet strip. If this situation is
undesirable for the application, the surge protector should be replaced. Units
with Power Blocker™ protection will cease to conduct power through the unit
once they have reached capacity. At that time, the unit needs to be replaced to
ensure proper protection. Units with Power Blocker™ 2 technology will cease
to conduct power through the unit once the MOV’s have reached capacity.
In the event of an overvoltage condition, the Instant Reset button on a Power
Blocker ™ 2 product will trip, and the unit will not conduct electricity. The
user can reset the circuit after the event to restore surge protection. If the red
led goes out on a Power Blocker™ 2 product, the unit needs to be replaced
to ensure proper protection. The Power Blocker™ 2 instant reset feature
protects the AC lines, and is not applicable to telephone or coaxial lines.
Standard surge protectors are not designed to protect against
sustained low voltage situations. Sustained low voltage situations
can cause damage to some connected equipment. If you are in an
area prone to sustained low voltage situations, you should purchase
an Uninterrupted Power Supply (UPS) with surge protection.
Power Blocker™ Protection Feature
Philips products with Power Blocker™ protection are designed to
sacrifice themselves in order to save equipment connected to it. Their
circuitry is designed to cut off all power to AC outlets in the event of an
electrical or power surge that overwhelms their protection. If your surge
protector is not allowing current to pass and the protection working LED
is off, then your surge protector has performed its duty – protecting your
equipment – and you must purchase a new unit to replace the expired unit.
Equipment connected to products with Power Blocker™ protection will
be additionally covered in the event of equipment damaged by a lightning
strike. No surge protector will entirely protect against a direct lightning
strike. The surge protector itself is expected to be damaged, thus performing
its duty, and you must purchase a new unit to replace the damaged unit.
• Surge protector models with telephone protection are designed to provide
maximum protection from surges present on standard two wire “dial up”
telephone service. Other communications networks which happen to use
modular jacks may not benefit from this protection. CAUTION: The telephone
feature of this product could be rendered inoperable if improperly installed.
Coaxial Cable Connections
Some Philips surge protector
models come with Coaxial Cable
surge protection. Instead of running
a connection directly from your
TV/VCR/Cable Box to the wall
jack, you must pass the connection
through the protected coaxial
connections on your surge protector.
• Connect your incoming
cable/broadband line to the
“Input” coaxial connector on
the surge protector. Connect
a coax cable into the “Output”
coaxial connector on the surge
protector, and connect the other
end of the Coaxial Cable to the
input coaxial connector of the
device you want to protect.
• To claim damage under the
Connected Equipment Warranty as a result of coaxial line transients,
equipment must be properly connected to a Philips surge protector which
offers coaxial line protection.
• If you fail to connect the Coaxial Cable protection, your
connected equipment will not be covered by the Connected
Equipment Warranty. Most TV/VCR damage can be prevented
if you take the time to connect Coaxial Cable protection.
• Surge protector models with coaxial protection are designed to provide
maximum protection from surges present on standard coax/broadband lines.
Other communications networks, such as antennas, satellite dishes, which
happen to use coaxial connections may not benefit from this protection.
You should select a Philips model specifically designed for DBS products for
additional protection.
CAUTION: The coaxial feature of this product could be rendered inoperable
if improperly installed.
If you have additional questions, or if you would like to locate the Philips retailer
nearest you, please contact our customer service department at (800) 233-8413.
Note: This device features an internal protection that will disconnect the
surge protective component at the end of its useful life but will maintain
power to the load - now unprotected. If this situation is undesirable for the
application, follow the manufacturer’s instructions for replacing the device.
IN/OUT Phone Line Protection
Splitter Phone Line Protection
Splits incoming phone line into
two outs. Ideal for people with
one telephone number, who use
a modem and telephone. Note:
Modem and phone can not be used
at the same time.
2-Device Phone Line Protection
Advanced two-line phone/modem/
fax protection. Allows use of two
devices simultaneaously.
www.philips.com
I2006-12/06
LIMITED WARRANTIES
Philips, Inc. (“Philips”) provides one or both of the following warranties
(Surge Protector Limited Warranty and Connected Equipment Limited
Warranty) to the original consumer of surge protectors sold under the
Philips brand names.
Provisions Applicable to Each Warranty
These warranties apply only to natural purchasers of surge protectors
for personal, family or household use, not to commercial, institutional
or industrial purchasers. These warranties are valid only in the United
States and Canada.
THESE WARRANTIES ARE IN LIEU OF ALL OTHER
EXPRESS WARRANTIES; AND ANY IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE DURATION OF THIS
WARRANTY.
EXCEPT AS PROVIDED IN THE CONNECTED EQUIPMENT
LIMITED WARRANTY (IF APPLICABLE), IN NO EVENT SHALL
PHILIPS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, CONSEQUENTIAL OR MULTIPLE DAMAGES* ARISING
OUT OF THE USE OF THE PHILIPS SURGE PROTECTOR.
Some states do not allow limitations on how long an implied
warranty lasts, and some states do not allow exclusion or limitation
of incidental or consequential damages, so the above limitations and
exclusions may not apply to you. These warranties give you specific
rights, and you may have other rights which vary from state to state.
*Examples of such excluded damages are loss of profits, loss of
savings or revenue, loss of use of the surge protector or the connected
equipment or any associated equipment, loss of software, cost of capital,
cost of any subsequent equipment, facilities or services, downtime, the
claims of third parties, including customers, and injury to property.
Surge Protector (Product) Limited Warranty
Philips warrants to the original consumer that each surge protector
will be free from defects in materials and workmanship under normal use
for its lifetime, which means until the surge protector has exceeded its
capacity to protect against surges and spikes. The “Protection Working”
indicator light will no longer be lit when this capacity is exceeded.
This warranty does not cover damages (a) as a result of an
Occurrence (as defined below); (b) as a result of an accident; (b)
by the use of parts not manufactured or sold by Philips; or (c) by
modification of the surge protector. After any repair or modification
of the surge protector by a facility not authorized by Philips, any
problems that arise will not be remedied under this warranty.
To make a warranty claim, consumer must contact the Philips customer
service department at and provide a full description of the (800) 233-8413
damage. The customer service department will provide the consumer with
a Return Authorization number (RA#). Philips will determine, at its sole
discretion, whether consumer should send the damaged surge protector
to Philips, or to an independent repair facility. If Philips so requests, the
consumer must, at his/her own expense, send the damaged surge protector,
along with a copy of the sales receipt, to the specified location, in secure
packaging (to prevent further damage) with the RA# clearly displayed on the
outside of the package, and with a full written description of the problem,
including the consumer’s name, address, and daytime phone enclosed.
Philips also reserves the right to examine the site where the damage occurred.
If the surge protector is covered under the Surge Protector Limited
Warranty, Philips will, at its sole discretion, at no cost to the consumer, repair
or replace defective surge protector parts, or replace the entire surge protector.
Connected Equipment Limited Warranty
Philips warrants to the original consumer that it will, at its sole
option, repair or replace any equipment properly connected through a
Philips surge protector to a properly wired AC power line with protective
ground and telephone/coax lines, which is damaged by from impulses
lightning, or other power transients, or by momentary (less than 1ms)
voltage surges or spikes (an “Occurrence”) if (a) the surge protector
did not function properly and protect the equipment because it had
defects in assembly, materials, or workmanship, causing it to operate
outside design specifications; (b) the surge protector shows clear signs
of damage; and (c) the damage resulted from the Occurrence.
This warranty does not cover (a) damages caused by acts of God,
including flood, erosion, or earthquake, but excluding lightning on products
with Power technology; (b) damages caused by a sustained low Blocker™
voltage situation, or a low voltage disturbance, including brownouts, sags,
or power outages; (c) damages caused by war, vandalism, theft, normal
use wear-and-tear, depletion, obsolescence, abnormal care or uses, or
abuse; (d) damage due to non-authorized program or system equipment
modification or alteration; or (e) damage to equipment that was not
directly connected to the surge protector at the time of the Occurrence.
This warranty extends through the lifetime of the surge protector,
which means until the surge protector has exceeded its capacity to
protect against surges and spikes. The “Protection Working” indicator
light will no longer be lit when this capacity is exceeded. The capacity
of the surge protector will be exceeded after an Occurrence.
This warranty is limited to losses that are not covered by a warranty
from the manufacturer of the connected equipment, or by the consumer’s
homeowners insurance or renters insurance policy. Consumer agrees
to first seek coverage under any such warranty or policy, and not seek
duplicate coverage from Philips. Consumer agrees to provide insurance
information to Philips, at its request; and after a claims settlement,
if applicable, Philips reserves the right to be subrogated under any
existing warranty from the manufacturer of the connected equipment
or under any existing insurance policies the claimant may have.
This warranty is limited to surge protectors which indicate on the
packaging an accompanying connected equipment warranty. After any
repair or modification of the surge protector by a facility not authorized by
Philips, any problems that arise will not be remedied under this warranty.
Your Philips surge protector must be plugged into a properly
grounded outlet. All connected equipment must be plugged directly
into your surge protector. Using any extension cord, adapters, other
grounding wires or electrical connections in conjunction with a
Philips surge protector will void all Philips warranties. All wires
leading into the equipment, including telephone and coaxial lines,
must pass through an appropriate Philips surge protector.
To claim damage as a result of telephone service line transients,
equipment must be properly connected to a Philips surge protector which
offers telephone line protection (see Handbook for installation instructions),
and your telephone service equipment must include a properly installed
and operating “primary protection” device at the service entrance. (Such
devices are normally added during telephone line installation.) If you
fail to connect the telephone line protection properly, your connected
equipment will not be covered by the Connected Equipment Warranty.
To claim damage as a result of coaxial line transients, equipment must
be properly connected to a Philips surge protector which offers coaxial line
protection (see Handbook for installation instructions). If you fail to connect
the coaxial cable protection properly, your connected equipment will not be
covered by the Connected Equipment Warranty.To make a warranty claim,
consumer must contact the Philips customer service department at (800) 233-
8413 and provide a full description of the damage. The customer service
department will provide the consumer with a Return Authorization number
(RA#). Philips will determine, at its sole discretion, whether consumer
should send the damaged equipment and the surge protector to Philips, or to
an independent repair facility. If Philips so requests, the consumer must, at
his/her own expense, send the damaged equipment and the surge protector,
along with a copy of the sales receipt, to the specified location, in secure
packaging (to prevent further damage) with the RA# clearly displayed on the
outside of the package, and with a full written description of the problem,
including the consumer’s name, address, and daytime phone enclosed.
Philips also reserves the right to examine the site where the damage occurred.
If the surge protector is covered under the Surge Protector Limited
Warranty, as discussed above, Philips will either repair or replace the surge
protector. If Philips determines that the Connected Equipment Limited
Warranty covers the damaged equipment, and that the equipment was
damaged as a result of the surge protector which is covered under the Surge
Protector Limited Warranty, Philips will either (a) authorize repair of the
connected equipment, at a cost up to the maximum amount set forth on the
packaging of the surge protector involved; (b) provide the consumer with
an equivalent equipment replacement; or (c) reimburse the consumer for
the present fair market value of the damaged connected equipment. The
present fair market value of the equipment will be determined according to
the current value specified in the most recent edition of the Orion Blue Book
by Orion Research Corporation, Roger Rohrs Publisher. If, applicable, the
equipment will be returned from Philips to the consumer at Philips expense.
www.philips.com

Especificaciones del producto

Marca: Philips
Categoría: No categorizado
Modelo: SPP3211WA

¿Necesitas ayuda?

Si necesitas ayuda con Philips SPP3211WA haz una pregunta a continuación y otros usuarios te responderán


No categorizado Philips Manuales

Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Philips

Philips TAT2205 Manual de Usario

24 Octubre 2024
Philips

Philips AWP2970 Manual de Usario

24 Octubre 2024
Philips

Philips 7600 series 70PUN7625 Manual de Usario

24 Octubre 2024
Philips

Philips DLA97878 Manual de Usario

24 Octubre 2024
Philips

Philips Straightcare Essential BHS378 Manual de Usario

24 Octubre 2024
Philips

Philips 3000 Series BHD388 Manual de Usario

24 Octubre 2024
Philips

Philips 32PFL3406 Manual de Usario

24 Octubre 2024
Philips

Philips SPN4081A Manual de Usario

24 Octubre 2024
Philips

Philips SPN5087B Manual de Usario

24 Octubre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024
Medion

Medion Life E74001 (MD 81035) Manual de Usario

27 Octubre 2024