Phoenix Gold ZR10001 Manual de Usario

Phoenix Gold receptor ZR10001

Lee a continuación 📖 el manual en español para Phoenix Gold ZR10001 (12 páginas) en la categoría receptor. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

POWERFUL AND COMPACT, CLASS D AMPLIFIERS

Model: ZR6004 / ZR10001 / ZR20001

• - powers on the amp when audio signal is suppliedHigh Level Auto-Turn On

• - compatible with aftermarket/original source unitsOEM Connection Ready

• - control bass with included ZRBC Remote Bass Ready (ZR10001 & ZR20001)

• Fanless Design - regulates temperature internally for quiet operation

• - versatile connectivity to suit any vehicleHigh & Low Level Inputs

• - enables maximum current supplyHeavy Duty Connector Block

• - protection against thermal damage, 4-Way Protected Circuit

reversed power, speaker polarity and low voltage

SPECIFICATIONS

All specications subject to change without notice.

www.phoenixgold-eu.com

ZR6004 / ZR10001 / ZR20001 - ZR-Series Ampliers

ZR6004 ZR10001 ZR20001

Class Class D Class D Class D

Frequency

Response 20Hz-20KHz 20Hz-400Hz 20Hz-400Hz

Dims (LxWxH(mm)) 253 x 160 x 48 243 x160 x 48 383 x 160 x 48

RMS Power

Ratings

175W x 4 @ 2ohm

105W x 4 @ 4ohm

350W x 2 @ 4ohm

bridged

1015W x 1 @ 1ohm

670W x 1 @ 2ohm

385W x 1 @ 4ohm

2015W x 1 @ 1ohm

1310W x 1 @ 2ohm

740W x 1 @ 4ohm

Signal to

Noise Ratio >96dB >96dB >96dB

High & Low Pass

Crossover 12dB per Octave 24dB per Octave 24dB per Octave

Subsonic Filter N/A 12dB per Octave 12dB per Octave

Crossover

Range 40Hz-6KHz 50Hz-250Hz 50Hz-250Hz

Subsonic

Crossover Range N/A 10Hz-55Hz 10Hz-55Hz

Bass Boost

@ 45Hz N/A 0 to +18dB 0 to +18dB

Low Level

Input Range 0.2V to 10V 0.2V to 10V 0.2V to 10V

High Level

Input Range 1V to 30V 1V to 30V 1V to 30V

Minimum Load

Impedance

2ohm stereo &

4ohm bridged 1ohm 1ohm

Note:

Phoenix Gold Ampliers have a minimum load impedance

of 2ohm per channel 4ohm bridged

ZR6004 / ZR10001 / ZR20001 - ZR-Series Ampliers

Installation Warnings

1. Ensure the +12V lead is disconnected from the battery before you

connect any new equipment

2. Ensure that the amplier mounting location and holes will not interfere

with the petrol tank, brake lines or electrical wiring.

3. Ensure the amplier is securely fastened to the vehicle to prevent the

amplier moving and causing damage in the event of an accident

4. Ensure all wiring is protected from sharp objects and from pinching or

crushing which could result in damage to the audio system

5. Ensure the mounting location has sufcient air ow around the

amplier. If the amplier is mounted in an enclosed space a 3” fan

with ducting should be used to assist with cooling.

6. Do not mount any amplier on a subwoofer enclosure as extended

exposure to vibration may cause damage to the amplier.

7. Ensure the minimum recommended gauge wire/cable or larger for all

amplier connections

8. Appropriate mounting is very important for prolonged life

expectancy of any amplier. Select a location that provides

protection from moisture. Keep in mind that an amplier should never

be mounted upside down. Upside down mounting will compromise

heat dissipation through the heat sink and could engage the thermal

protection circuit.

www.phoenixgold-eu.com

ZR6004 / ZR10001 / ZR20001 - ZR-Series Ampliers

Connection

Ensure the audio system is turned off before making any connections to the

amplier, speakers or source unit. Failure to do so could result in permanent

damage to the audio system.

Ensure the correct gauge cable is used for all connections; consult the cable

calculator diagram below for the correct gauge cable for your installation.

Total

Amps

Cable

Length >

M 0-1 1-2 2-3 3-4 4-5 5-6 6-7 7-9

FT 0-4 4-7 7-10 10-13 13-16 16-19 19-22 22-28

0-20 14 12 12 10 10 8 8 8

20-35 12 10 8 8 6 6 6 4

35-50 10 8 8 6 4 4 4 4

50-65 8 8 6 4 4 4 4 2

65-85 6 6 4 4 2 2 2 0

85-105 6 6 4 2 2 2 2 0

105-125 4 4 4 2 0 0 0 0

125-150 2 2 2 0 0 0 0 0

The above chart shows cable gauges to be used if no less than a 0.5V drop is acceptable.

If aluminium wire is used, the gauges should be of an even larger size to compensate.

Cable gauge size calculation takes into account terminal connection resistance.

1. +12V Power

Ensure ALL other cable connections are completed

before connecting this cable to the battery. PHOENIX

GOLD ampliers should be connected directly to the

12V battery terminal using the appropriate gauge cable.

Start at the vehicles battery and run the cable through

to the amplier. PHOENIX GOLD recommends the use

of rubber grommets when passing any cable through

metal panels to avoid sharp corners or panels that could

cut through the insulation of the cable. An inline fuse or

circuit breaker MUST be used within 30cm (12”) of your

battery; this will prevent the potential risk of a re caused

by a short in your power cable (see spec table for

recommended inline fuse/circuit breaker ratings).

Connect the other end of your power cable to the

battery, but remember to leave the fuse out or circuit

breaker off until all other cable connections are made.

AMPLIFIER CONNECTION

123

ZR6004 / ZR10001 / ZR20001 - ZR-Series Ampliers

2. Remote Turn-On

This connection turns the amplier on and should be connected to the ‘Remote Turn on’

wire from the Head Unit. If one is not available a switched +12V source must be used,

such as a power antenna wire or ACC +12V.

If you are using high level (speaker) inputs and a remote turn on wire is not available, then

instead the ‘Auto Turn-On’ switch must be set to ON.

3. Ground

Connect the Ground/Earth cable for your amplier rst. Ensure that the location is a good

source of ground (preferably the chassis/oor pan). Investigate the area you wish to use

to ensure it is free of wiring, vacuum lines, brake and fuel lines. Use either a wire brush or

sandpaper to expose bare metal, this will provide a high current contact for your ground

connection. Use the same gauge cable for the ground cable as you did for the power

cable. Secure the ground cable to the ground point with a bolt, star washer and nut.

Apply some neutral cure silicon to the bolt and bare metal to prevent possible water

leaks and rust. Connect the other end of your ground cable to the amplier.

4A. Speaker Output Connection

(ZR6004 ONLY)

Ensure the correct polarity is observed when connecting

speakers/subwoofers.

2ohm minimum speaker impedance for stereo

operation (per channel).

4ohm minimum speaker impedance for bridged

operation.

4B. Internally Linked Output

(ZR10001 - ZR20001)

The ZR20001 Monoblock amplier provides dual output

connections to simplify wiring when using 2 subwoofers

or a dual voice coil subwoofer. Both positive and

negative terminals and internally connected or linked

in parallel. For dual coil (2 x 4ohm) or two single coil

(4 ohm) subwoofers connect each coil to positive or

negative terminal. For a standard single coil subwoofer

connect to either positive and either negative terminal.

www.phoenixgold-eu.com

ZR6004 / ZR10001 / ZR20001 - ZR-Series Ampliers

ZR6004

Example of 3 Channel

conguration

2 x Front/Rear Speakers

(4Ohm Subwoofer)

Bridged Rear Channels

ZR6004 / ZR10001 / ZR20001 - ZR-Series Ampliers

ZR6004

ZR10001/

ZR20001 14

6811 10 13

667 799

Especificaciones del producto

Marca:	Phoenix Gold
Categoría:	receptor
Modelo:	ZR10001

¿Necesitas ayuda?

Si necesitas ayuda con Phoenix Gold ZR10001 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

receptor Phoenix Gold Manuales

Phoenix Gold ZXM700.5 Manual de Usario

16 Septiembre 2024

Phoenix Gold Z3001i Manual de Usario

16 Septiembre 2024

Phoenix Gold Z3004i Manual de Usario

16 Septiembre 2024

Phoenix Gold ZQ9004 Manual de Usario

15 Septiembre 2024

Phoenix Gold Z6001i Manual de Usario

15 Septiembre 2024

Phoenix Gold ZXM500.1 Manual de Usario

15 Septiembre 2024

Phoenix Gold ZT15001 Manual de Usario

15 Septiembre 2024

Phoenix Gold ZXM500.4 Manual de Usario

15 Septiembre 2024

Phoenix Gold ZT6004R Manual de Usario

15 Septiembre 2024

Phoenix Gold ZDA4.6 Manual de Usario

15 Septiembre 2024

receptor Manuales

Últimos receptor Manuales

Crown CDi DriveCore 2|300BL Manual de Usario

27 Octubre 2024

Boss PT3000 Manual de Usario

27 Octubre 2024

Speco Technologies PBM120AT Manual de Usario

27 Octubre 2024

Fosi Audio V3 Manual de Usario

26 Octubre 2024

Jensen CAR710-4BC Manual de Usario

25 Octubre 2024

Onkyo TX-RZ830 Manual de Usario

24 Octubre 2024

Pioneer VSX-1122K Manual de Usario

22 Octubre 2024

Yamaha HTR-5072 Manual de Usario

21 Octubre 2024

NAD C 355BEE Manual de Usario

20 Octubre 2024

Yamaha RX-A810 Manual de Usario

20 Octubre 2024