Pioneer PDP-S09-LR Manual de Usario

Pioneer Vocero PDP-S09-LR

Lee a continuación 📖 el manual en español para Pioneer PDP-S09-LR (28 páginas) en la categoría Vocero. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/28
PDP-S09-LR
Operating Instructions
Mode d'emploi
Bedienungsanleitung
Istruzioni per l'uso
Gebruiksaanwijzing
Manual de instrucciones
Speaker System
Enceintes acoustiques
Lautsprechersystem
Sistema di diffusori
Luidsprekersysteem
Sistema de altavoces
2
English
CHECKING THE ACCESSORIES
7Speaker cable x 2
Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system so you will know how to make
the most of its performance. After you have finished reading
the instructions, put them away in a safe place for future
reference.
BEFORE USE
÷The nominal impedance of this speaker system is 8 ohms.
÷In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
÷Do not supply power to the speaker system in
excess of the maximum permissable input. This
can result in damage or a possible fire hazard.
÷When connecting or disconnecting pin-plugs, be
sure that amplifier power is OFF.
÷When using a graphic equalizer to emphasize loud
sounds of a high frequency range, do not use
excessive amplifier volume.
÷Do not force a low-powered amplifier to produce a
loud volume of sound (the amplifier’s harmonic
distortion will be increased, and you may damage
the speaker).
÷Please handle the speakers with sufficient care, as
the grille net and the cabinet can become damaged
or broken when they are subjected to strong external
impacts.
÷Placing a CRT computer screen or CRT monitor near to
the speakers may result in interference or color distortion.
If this happens, distance the monitor from the speakers.
This product is designed exclusively for use with the
PDP-4330HD,PDP-433HDE,PDP-433HDG Pioneer plasma
display.
7Operating Instructions
Flat countersunk head screw x 4
Hexagon socket head screw x 4
7Speaker mounting fittings
For top right side x 1 For top left side x 1
For bottom x 2
7Speaker mounting bolts
7Mounting tool (Hex wrench)
NOTE:
÷
Always use the accessory mounting fittings for
installation.
÷
When screws other than those enclosed as accessories
are used to install the speakers, the speakers may drop
off or accidents may be caused. Always use the screws
enclosed as accessories.
INSTALLATION ON THE PLASMA
DISPLAY
Perform installation according to the following steps to 1 2.
1Attach the mounting fittings to the
speakers.
The illustration shows the right speaker.
For top side
Mounting plate
Flat countersunk
head screw
For bottom
1 The top side fittings are dif-
ferent for the right and the
left side, and they must be
matched correctly.
2 Install the mounting fittings
with bolts at the positions
shown in the figure on the
left.
Notes on Installation Work:
This product is marketed assuming that it is installed by
qualified personnel with enough skill and competence.
Always have an installation specialist or your dealer install
and set up the product.
PIONEER cannot assume liabilities for damage caused
by mistake in installation or mounting, misuse,
modification or a natural disaster.
CAUTION
3
English
English
NOTE:
÷
When the display is to be moved after speaker
installation, do not hold the display by the speakers. Hold
the bottom of the display to move it.
÷
The grille nets are designed to protect the speakers,
however excessive force (such as pushing on, or insert-
ing objects between the grille nets) may result in dam-
age.
2Attach the speakers to the display.
Install the unit marked "RIGHT" on the right side of the display.
Hexagon socket
head screw
Plasma display
Install the unit marked "LEFT" on the left side of the display.
Hexagon socket
head screw
1To attach the speakers to the display, start by placing the
upper screw where indicated, tightening until there is a
small space of about 5mm between the head of the screw
and the display.
2Check the rear of the speakers for the LEFT and RIGHT
indicators to make sure you are attaching the correct
speaker to the corresponding right or left side. Make sure
the UP mark is pointing up, and then attach the speaker
by fitting the upper mounting over the head of the screw
and sliding down until snug.
3Affix the lower fitting to the display and tighten the screw
about halfway.
4 Adjust the position so that the gap between the speaker
and the display is uniform, and then tighten the screws
firmly.
Plasma display
1Switch off the power of the plasma display.
2Connect the input terminals of the speaker system and
the speaker output terminals of the plasma display with
the accessory speaker cable. Make sure the positive (ª)
and negative ( ) terminals match when connecting.·
To the terminal·To the terminalª
(Speaker output terminals of the plasma display)
· terminal (black)
2. Push the lever, insert the cable into the hole, and release the lever.
1. Remove the insulation and twist the core ends together.
ª terminal (red)
CONNECTION TO A PLASMA
DISPLAY
1Connecting the speaker cables
÷After connection to the terminals, pull lightly on the cable
to confirm that the tips of the cable are properly connected
to the terminals. An imperfect connection can cause
sound interruptions and noise.
÷ ª ·When cable cores stick out and and lines are short-
circuited, an excessive load will be applied to the plasma
display and the operation will stop or trouble will be
caused.
÷When the polarity is reversed for one speaker (left or right)
at the time of connection to the plasma display, the bass
reproduction will be reduced, the sound positioning will
be lost, and a correct stereo effect will not be obtained.
Input terminal of speaker
3. For the input terminals on the plasma display, push the tab to the
open position, and insert the wire. Then, close tab firmly to secure
the wire in place.
ª · · ª
R L
Input terminal of plasma
display
Black
Red

Especificaciones del producto

Marca: Pioneer
Categoría: Vocero
Modelo: PDP-S09-LR

¿Necesitas ayuda?

Si necesitas ayuda con Pioneer PDP-S09-LR haz una pregunta a continuación y otros usuarios te responderán


Vocero Pioneer Manuales

Pioneer

Pioneer SP-T22A-LR Manual de Usario

14 Octubre 2024
Pioneer

Pioneer X-CM66 Wit Manual de Usario

12 Octubre 2024
Pioneer

Pioneer TS-C131PRS Manual de Usario

29 Septiembre 2024
Pioneer

Pioneer TS-Z65CH Manual de Usario

22 Septiembre 2024
Pioneer

Pioneer TS-T736 Manual de Usario

16 Septiembre 2024
Pioneer

Pioneer S-ES21-CR-K Manual de Usario

16 Septiembre 2024
Pioneer

Pioneer XPRS1182ST Manual de Usario

15 Septiembre 2024
Pioneer

Pioneer XPRS1152ST Manual de Usario

15 Septiembre 2024
Pioneer

Pioneer XPRS152 Manual de Usario

15 Septiembre 2024
Pioneer

Pioneer XW-BTSA1-K Manual de Usario

13 Septiembre 2024

Vocero Manuales

Últimos Vocero Manuales

Continental Edison

Continental Edison CELED53HP20V2B4 Manual de Usario

27 Octubre 2024
Canton

Canton Vento 830.2 Manual de Usario

27 Octubre 2024
Jamo

Jamo S7-25C Manual de Usario

27 Octubre 2024
Bowers Wilkins

Bowers Wilkins 707 S2 Manual de Usario

27 Octubre 2024
Monacor

Monacor GLS-301/GR Manual de Usario

27 Octubre 2024
Monitor Audio

Monitor Audio Silver C150 Manual de Usario

26 Octubre 2024
FBT

FBT MITUS 210M Manual de Usario

26 Octubre 2024
CyberData Systems

CyberData Systems SIP 011398 Manual de Usario

26 Octubre 2024
Lamax

Lamax PartyGo1 Play Manual de Usario

26 Octubre 2024
IKEA

IKEA SYMFONISK 405.847.50 Manual de Usario

26 Octubre 2024