Pulse ShowerSpas Kauai III 1011-III Manual de Usario

Pulse ShowerSpas Sistema de ducha Kauai III 1011-III

Lee a continuación 📖 el manual en español para Pulse ShowerSpas Kauai III 1011-III (4 páginas) en la categoría Sistema de ducha. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Kauai III Rain Shower System

Model #1011-BN, 1011-CH & 1011-ORB

PW-91011-1125BRN, PW-91011-1125CP, PW-91011-1125BRZ

PW-91011-1118BRN, PW-91011-1118CP, PW-91011-1118BRZ

Owner's Manual

Parts Legend

1. ½" x 2" NPT Nipple

2. Inlet Fitting

2.1 check valve/restrictor

3. Top Escutcheon

4. Top Tee

5. Shower Arm

6. Shower Head

7. Shower Pipe**

8. Soap Dish

9. Hand Shower Holder

10. Hand Shower

11. Stainless Steel Hose

12. Diverter Body

13. Bottom Escutcheon

14. Lower Mount Screw ..............(2)

15. Lower Mount (w/ 3MTape)

16. Wall Anchor ...........................(2)

17. Set Screw - 2.5mmX4mm

18. Swivel Joint

19. Check Valve

20. Set Screw - 2.5X5mm

21. Rubber Washer (3) .............

22. Diverter Handle

23. 2.5mm Hex Wrench

24. PTFE Thread Sealant Tape

25. Set Screw - 2.5X8mm*

26. Shower Pipe Nut

27. Tapered Rubber Seal

28. Diverter Cartridge

29. Glue

oe s

no t

app ly

mo Del

1077 * *4”

shor t er

s p HOWER IPE (7)

ava i lab l e

fo r

pu r c h as e

www

ul s e

ho w er

pa s

com

6.38

in. -

162 mm

5 in. -

127mm

**When using optional 4 inch shorter pipe.

~26

1/8 1/8 in. - 664 mm [ ~22 in. - 562 mm**]

5/16 5/16 [ in. - 694 mm 23 in. - 592 mm**]

5/16 in. - 846 mm [ 29 5/16 in. - 562 mm**]

5/16 5/16in. - 846 mm [ 29 ]in. - 562 mm**

1/4 in. - 413 mm

in. - 508 mm

in. - 610 mm

1/4 1/4 [ in. - 920 mm 32 in. - 819 mm**]

in. - 228 mm

3.62 in. -

92 mm

Finish Wall Line

Installation Instructions

Thank you for choosing this Shower System by PULSE ShowerSpas!

Assembly and installation of the Shower System is designed

to be quick and easy. If you have installation questions or

performance problems, visit www.pulseshowerspas.com for

customer support

Please read instructions carefully, become familiar with all parts,

installation procedures and tools required. Follow steps in order

presented to help avoid mistakes.

FOR NEW CONSTRUCTION OR

COMPLETE REMODEL

• A hot/cold mixing valve is required (NOT INCLUDED)

• Nipple should extend

⁄

" past nished wall surface.

TOOLS REQUIRED

Adjustable wrench, Phillips screwdriver, pencil, 2.5mm hex

wrench, 3mm hex wrench

ASSEMBLY

1. Determine length of brass NPT nipple (1) needed:

a. Place mark on existing shower arm at wall surface.

Unscrew shower arm from elbow in wall.

b. Measure distance from mark on shower arm to end of

shower arm threads. Add

⁄

" to this measurement, and

then round to nearest

⁄

Example 1: If measurement = 1

⁄

", add

⁄

" = 1

⁄

rounded = 2" NPT nipple—this is the length needed.

Example 2: If measurement = 1

⁄

", add

⁄

" = 2

⁄

rounded = 2" NPT nipple—this is the length needed.

IMPORTANT: If shower arm is located above tile/berglass

wall surface you must add distance from sheetrock to face

of tile/berglass shower wall to the above measurement.

NOTE: If supplied 2" nipple (1) is not correct length based on

above formula, you must obtain correct size NPT brass

nipple (sold separately), available at most hardware stores.

2. Apply generous amount of PTFE Thread Sealant Tape (24)

to both ends of nipple (1).

3. Hand tighten inlet tting (2) onto nipple (1), then nipple

to tting in wall. Use adjustable wrench on inlet tting to

tighten both connections simultaneously until both are

secure with no leaks.

4. Slide hand shower holder (9) o shower pipe (7).

5. Slide soap dish (8) onto shower pipe to desired position

and secure with set screw (25). For model 1077 slide soap

dish retainer onto shower pipe. Slide plastic soap dish onto

shower pipe and push soap dish down until ush

with retainer.

CAUTION—DO NOT OVERTIGHTEN

6. Reinstall hand shower hanger (9).

7. Secure swivel joint onto bottom of diverter body (12). Swivel

joint should move freely side to side.

CAUTION—DO NOT OVERTIGHTEN

8. Insert shower pipe (7) into top tee (4). Secure with set screw

(17).

9. Slide top escutcheon (3) over top tee (4).

HINT—Lubricate escutcheon o-ring; a small amount of

soapy water will do the trick.

10. Slide bottom escutcheon (13) over diverter body (12).

HINT—Lubricate escutcheon o-ring; a small amount of

soapy water will do the trick.

11. Loosen set screw (20) on diverter and slide lower mount (15)

into diverter body (12).

12. Push top tee (4) over inlet tting (2) until ush against

tting. Position diverter body (12) so shower pipe is plumb

(vertical).

13. Mark location of lower mount with pencil.

14. Wall surface must be clean of any residue and

completely dry.

OPTION 1: 3M Tape

Remove covering of 3M Tape and position mount on

marked locations.

OPTION 2: Glue

Apply glue as indicated in Fugre 1. remove covering of 3M

tape and position mount on marked location.

15. Apply pressure to mount for 30 seconds by pushing rmly

against the wall. To ensure proper adhesion, allow one hour

before using your ShowerSpa and keep area around the

mount as dry as possible for the rst 24 hours. Tape and

glue will be fully cured after 24 hours.

OPTIONAL: Secure lower mount with permanent walll anchors.

Mark hole locations in lower mount (15). Drill 1

1/4"

deep

holes using 6mm (1/4") masonry/tile drill bit. Insert wall

anchors (16) and secure lower mount with screws (14).

CAUTION —LIVE PLUMBING IN WALL

16. Position shower pipe (7) parallel to wall by sliding diverter

body (12) on lower mount (15). Secure diverter to lower

mount with set screw (20).

17. Insert rubber washer (21) into both ends of hose (11).

Connect hex head end to swivel joint (18) and tapered

end to hand shower (10). Place hand shower (10) into

adjustable hanger (9).

18. Tighten shower head (6) securely to shower arm (5).

Tape

Glue

Back of wall mount

Especificaciones del producto

Marca:	Pulse ShowerSpas
Categoría:	Sistema de ducha
Modelo:	Kauai III 1011-III
Color del producto:	Zwart
Pantalla incorporada:	Nee
Tipo de embalaje:	Blister
Número soportado de baterías/baterías:	2
Interfaz:	IR Draadloos
Cantidad por paquete:	1 stuk(s)
Compatibilidad de marca:	Alle merken
Número de botones:	8
Rango maximo:	- m
Teclas retroiluminadas:	Nee
Recargable:	Nee
Tipo de entrada:	Drukknopen
Uso correcto del mando a distancia.:	DVD/Blu-ray, TV, TV Tuner, TV set-top box
Tipo de Batería:	AAA