Radial Engineering ProAV1 Manual de Usario

Radial Engineering No categorizado ProAV1

Lee a continuación 📖 el manual en español para Radial Engineering ProAV1 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 14 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

97 8

INPUT PANEL

1. ¼” INPUT & THRU - input connection

for instruments and thru-put for on-stage

ampliﬁ er.

2. 3.5mm TRS - input connection for stereo

-10dB consumer audio electronics.

3. RCA INPUT - left and right input

connection for stereo -10dB consumer

audio electronics.

4. RCA THRU - left and right parallel thru-

put of signals connected to the ¼”, 3.5mm

TRS and RCA inputs.

5. -15dB PAD - reduces the input level

by 15dB to prevent overload from high

output devices.

6. XLR INPUT - this recessed switch

selects between the hi-Z and the XLR

inputs.

OUTPUT PANEL

7. XLR LINE INPUT - this XLR input is

speciﬁ cally designed to accept +4dB line-

level signals from balanced sources.

8. GROUND LIFT - disconnects pin-1 on

the XLR output connector to help reduce

noise caused by ground loops.

9. XLR OUTPUT - balanced, 600 ohm,

mic-level output is 100% transformer-

isolated and compatible with mic splitters

and console preamps.

CONSTRUCTION

10. BOOK-END DESIGN - 14 gauge steel

outer shell provides a protective zone for

the switches and connectors.

11. FULL BOTTOM PAD - neoprene foam

foot provides electrical isolation and plenty

of friction to stay put on hectic stages.

12. WELDED I-BEAM CASE - inner steel

enclosure is made extremely rigid with I-

beam proﬁ le. Eliminates stress that could

torque the PC board and cause solder

joint failure.

13. MILITARY-GRADE - double-sided PCB

is bolted to steel standoffs for toughness.

14. RADIAL TRANSFORMER - linear freq.

response from 20Hz to 18kHz for natural

sound. Mu-metal shield to eliminate

electromagnetic interference.

15. ISOLATED CONNECTORS - are

made from extremely tough glass-ﬁ lled

nylon for true electrical isolation from

chassis ground.

www.radialeng.com

ProAV1 Direct Box

Users Guide

True to the Music

ProAV1 SPECIFICATIONS

Frequency response 20Hz to 18kHz +/- .5dB

Total harmonic distortion 0.01% THD 20Hz to 20kHz

Input Unbalanced high-Z -10dB RCA, ¼” and 3.5mm TRS

Balanced low-Z +4dB XLR

Output Balanced 600-Ohm, mic-level, pin-2 hot

Input pad -15dB

Power requirement None, completely passive

Size 3.25” x 5” x 1.875”

Weight 1.6 lbs

1 62 3 5

Radial Engineering

1638 Kebet Way, Port Coquitlam BC V3C 5W9

Tel: 604-942-1001 Fax: 604-942-1010

email: info@radialeng.com

Radial Engineering is a division of C•TEC (JP CableTek Electronics Ltd.)

Radial ProAV1 users guide V1.0 - Part #: R870 1140 00

Subject to change without notice

ProAV1 User GuideRadial Engineering ProAV1 User GuideRadial Engineering

RADIAL LIMITED THREE YEAR TRANSFERABLE

WARRANTY

Radial Engineering - a division of JP Cabletek Electronics Ltd. - warrants this

product to be free from defects in material and workmanship and will remedy

any such defects free of charge according to the terms of this warranty. Radial

Engineering will repair or replace at its option any defective component(s)

of this product, excluding the ﬁ nish, the bottom foam pad and wear and tear

from normal use, for a period of three (3) years from the original date of

purchase. In the event that a particular product is no longer available, Radial

Engineering reserves the right to replace the product with a similar product of

equal or greater value. To make a request or claim under this limited warranty,

the product must be returned prepaid in the original shipping container (or

equivalent) to Radial Engineering or to an authorized repair centre and

you must assume the risk of loss or damage. A copy of the original invoice

showing date of purchase and the dealer name must accompany any request

for work to be performed under this limited warranty. This limited warranty

shall not apply if the product has been damaged due to abuse, misuse,

misapplication, accident or as a result of service or modiﬁ cation by any other

than an authorized repair centre.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE

ON THE FACE HEREOF AND DESCRIBED ABOVE. NO WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO,

ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE, SHALL EXTEND BEYOND THE RESPECTIVE

WARRANTY PERIOD DESCRIBED ABOVE OF THREE YEARS. RADIAL

ENGINEERING SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS

ARISING FROM THE USE OF THIS PRODUCT. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU LIVE.

True to the Music

CONGRATULATIONS

on your purchase of the Radial ProAV1 passive direct box. This innovative DI fea-

tures a ‘Swiss army knife’ compliment of connectivity options making the PROAV1

the perfect DI for professional AV integrators and rental companies that regularly

deal with a variety of system interface problems. As with all Radial products the

ProAV1 is easy to use. This short manual contains all the information you need to

start using the ProAV1 right away. For more information on the ProAV1 and other

Radial products, visit our website at www.radialeng.com.

The Radial ProAV1 is a clever and useful device that will provide you with years of

problem-solving connectivity. It may even save the show ten minutes before curtain.

Enjoy!

INTRODUCTION

The ProAV1 is a single channel DI with stereo inputs and a merge function that

mixes left and right signals to a mono, mic-level, 600 Ohm XLR output. Upon in-

spection, you will notice the Radial ProAV1 is equipped with multiple input connector

formats that allow virtually any audio device to be connected. In addition to standard

¼” instrument inputs, the ProAV1 is equipped with 3.5mm and RCA jacks for -10dB

consumer audio devices like MP3 and CD players. An XLR jack allows +4dB line-

level pro-audio equipment to be properly connected to a microphone snake and

console preamp.

At the heart of the ProAV1 is the Radial transformer that balances the signal and

provides level and impedance conversion while isolating noise caused by ground

loops. Radial transformers, manufactured for optimum signal transfer and minimal

insertion loss, are exceptional for their linear frequency response and ability to han-

dle high input levels without distortion. The transformer is mounted in a mu-metal

can for protection against electromagnetic ﬁ elds produced by power transformers,

lighting dimmers and video displays.

The ProAV1 is completely passive and therefore does not require any power what-

soever to make it work. With its heavy-duty steel construction the ProAV1 is well

suited for touring and rental use.

CONNECTING THE ProAV1

Before connecting the ProAV1 make sure the sound system is turned off and all

levels are set to zero. This will avoid any pops in the sound system that could cause

damage to speakers. Also conﬁ rm that the PAD, LIFT and XLR INPUT SELECT but-

tons are in their “out” positions. Phantom power will not damage the ProAV1.

ProAV1 BLOCK DIAGRAM

Follow the block diagram from the inputs on the left to the output on the right. A really cool

feature shown in the diagram is the hi-Z input jacks are paralleled together in stereo. This

makes any unused hi-Z jack a handy patch point to pass the signal on to mixers or ampli-

ﬁ ers. Next, the stereo inputs are merged to mono through a resistive network designed to

minimize phase cancellation.

ProAV1 User GuideRadial Engineering ProAV1 User Guide ProAV1 User GuideRadial EngineeringRadial Engineering

-15dB PAD

The ProAV1 is equipped with a -15dB input PAD to prevent overload distortion when

interfacing high output devices like CD players. The PAD reduces the input to the

transformer and will not effect the level at the thru-put jacks. The XLR input is preset

for +4dB signals and is not affected by the PAD.

TRANSFORMER ISOLATION

The ProAV1 transformer converts hi-Z inputs to a low impedance, balanced, mic-level

signal. A huge beneﬁ t of using transformers for signal conversion is the isolation the

transformer provides by preventing the ﬂ ow of ground currents between the input and

output. This isolation effectively blocks hum and buzz caused by ground loops.

GROUND LIFT

To make grounding as ﬂ exible as possible the ProAV1 features a ground LIFT switch.

When the LIFT switch is in the “in” position, pin-1 on the XLR output is disconnected,

interrupting the ground between the source device and mixing console. This can help

to reduce noise caused by ground loops.

XLR OUTPUT

The ProAV1 produces a balanced, 600 Ohm, mic-level signal that is compatible with

microphone snakes systems and mixing consoles preamps. Balanced signals can

drive very long cables without appreciable noise or signal loss.

ACCESSORIES

OPTIONAL J-RAK

The optional J-RAK is a 2RU rack

chassis that allows up to 8 Radial

devices in one neat 19” package. The

DIs can be mounted with either the input

side or output side facing the front.

OPTIONAL J-CLAMP

The optional J-CLAMP can mount a

single Radial device to virtually any

surface. Perfect for hiding away inside

racks, on podiums or under tables.

RCA & 3.5mm JACKS - CONSUMER -10dB AUDIO EQUIPMENT

Consumer audio electronics like CD players, computer sound cards and MP3 players

may connect directly to the ProAV1 without cumbersome adaptors through the 3.5mm

and RCA inputs.

¼” JACKS - INSTRUMENTS

Musical instruments may be connected to the ¼” input jacks. When connecting a mono

instrument, like a bass guitar, the instrument connects to the ¼” INPUT jack and the play-

ers on-stage ampliﬁ er is connected to the ¼” THRU jack.

When connecting stereo instruments, like sythesizers, the two ¼” jacks may be used for

left and right channels. The signal may be accessed at the RCA THRU or 3.5mm jacks

and passed to mixers, sound cards or on-stage ampliﬁ ers.

XLR BALANCED +4dB INPUT

Pro-audio equipment with a balanced +4dB line output may be connected to the ProAV1

XLR input. The XLR input is activated by a recessed switch on the side of the ProAV1.

Push the recessed switch in to activate the XLR input and disable the ¼”, 3.5mm and

RCA inputs. The ProAV1 will convert the +4dB line input to a mic-level signal at the XLR

output.

Computer sound card uses 3.5mm jack. RCA jacks output stereo

signal to local mixer. Mono mic-level output to PA system.

3.5mm Stereo

RCA Stereo Thru

Mono

Instrument uses ¼” input with thru-put to amp.

Mic-level output to PA system.

Thru

Balanced +4dB audio source uses XLR input.

+4dB Line-level

Mic-level

Especificaciones del producto

Marca:	Radial Engineering
Categoría:	No categorizado
Modelo:	ProAV1
Ancho:	305 mm
Profundidad:	244 mm
Bluetooth:	Ja
Estándares wifi:	802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Versión Bluetooth:	5.0
red LAN:	Ja
Número de puertos USB 2.0:	4
Número de puertos Ethernet LAN (RJ-45):	1
Salidas de auriculares:	1
Soporta Windows:	Windows 10
Zócalo del procesador:	LGA 1151 (Socket H4)
Fabricante del procesador:	Intel
Memoria interna máxima:	64 GB
Número de puertos USB 3.2 Gen 2 (3.1 Gen 2) Tipo C:	1
Canales de salida de audio:	7.1 kanalen
Tipo de interfaz Ethernet:	Gigabit Ethernet
placa base con chipset:	Intel Z390
Número de puertos USB 3.2 Gen 2 (3.1 Gen 2) Tipo A:	5
Tipo de ranura de memoria:	DIMM
chip de audio:	Realtek ALC1220
Canal de memoria:	Dubbelkanaals
Ranuras PCI Express x16 (Gen. 3.x):	3
Ranuras PCI Express x1 (Gen 3.x):	3
Interfaces de unidad de almacenamiento compatibles:	M.2, SATA III
Componente para:	PC
Controlador LAN:	Killer E2500
Tipos de incursión:	0, 1,5, 10
Número de conectores SATA III:	6
No ECC:	Ja
Procesadores compatibles:	Intel Celeron, Intel Core i3, Intel Core i5, Intel Core i7, Intel Pentium
Tipos de memoria soportados:	DDR4-SDRAM
Wifi.:	Ja
Tipos de unidades de almacenamiento compatibles:	HDD & SSD
Familia de chipsets de placa base:	Intel
Factor de forma de la placa base:	ATX
Número de ranuras de memoria:	4
Velocidades de reloj de memoria admitidas:	2133,2400,2666,2800,3000,3200,3300,3333,3400,3466,3600,3733,3866,4000,4133,4200,4266,4300,4400,4500 MHz
tipo de BIOS:	UEFI AMI
Soporte para procesamiento paralelo:	2-Way SLI, 3-Way CrossFireX
Conexión para refrigerador de CPU:	Ja
Conexiones para ventiladores de caja:	5
Conector de alimentación ATX (24 pines):	Ja
Conexiones USB 2.0:	2
Conexión para panel de audio en el frente:	Ja
Puerto de entrada S/PDIF:	Ja
Memoria sin búfer:	Ja
Conexiones USB 3.2 Gen 1 (3.1 Gen 1):	2
Conexión de intrusión al chasis:	Ja
Conector de alimentación EPS (8 pines):	Ja
Conector de antena WiFi-AP:	2
Capacidades de módulos de memoria admitidas:	16GB
Borrar puente CMOS:	Ja
Número de ranuras M.2 (M):	3
Carril de conexión LED RGB:	Ja
Conectores USB 3.2 (3.1 Gen 2):	2