Rega RB330 Manual de Usario

Rega No categorizado RB330

Lee a continuación 📖 el manual en español para Rega RB330 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
Names of Tonearm parts
Names of Tonearm parts
Names of Tonearm parts
Names of Tonearm partsNames of Tonearm parts
Introduction
Introduction
Introduction
IntroductionIntroduction
Designed using the latest 3D CAD & CAM technology,
the new RB330 is the culmination of more than 35 years
of tonearm design experience. Featuring a brand
new bearing housing and our latest tonearm tube
designed using intelligent redistribution of mass, ensure
this arm will exhibit fewer points of possible resonance.
Extreme stability with almost friction free movement
from the new high precision, horizontal and vertical
bearing assemblies guarantees to gather more
information from your vinyl than ever before. The
RB330 offers a new bias assembly, re designed stiffer -
vertical bearing housing, integrated arm clip and an
improved spring housing with easier to read numbers.
You will also find Rega made new low capacitance
phono cables terminated with high specification
Neutrik plugs.
Arm balancin
Arm balancin
Arm balancin
Arm balancinArm balancing and setup
g and setup
g and setup
g and setupg and setup
With the cartridge correctly mounted and with the
stylus guard removed, ensure that the tracking force
dial and bias adjustment are set to zero. Adjust the
balance weight until the arm is floating with the stylus “ ”
approximately 1mm clear of the record. It is
Note:
Note:
Note:
Note:Note:
normal for the arm to swing back towards the arm clip
position even with the bias set at zero. Therefore it is
advisable to gently hold the arm bearing carrier (just
below the tracking dial) thus preventing horizontal
movement during the balancing procedure.
Applying t
Applying t
Applying t
Applying tApplying tracking pres
racking pres
racking pres
racking presracking pressure
sure
sure
suresure
Once the arm is balanced, rotate the tracking force
adjustment dial to the required tracking force.
Numbers to are marked on the dial. If in doubt, ‘0’ ‘3’
it is usually advisable to use a tracking force that
corresponds with the upper limits of the cartridge
manufacturer s range.’
Applying
Applying
Applying
Applying Applying Anti
Anti
Anti
Anti Anti Skatin
Skatin
Skatin
Skatin Skating (bias) adjust
g (bias) adjust
g (bias) adjust
g (bias) adjustg (bias) adjustment
ment
ment
mentment
-
-
-
--
Set the bias adjustment slider located to the same
figure as the cartridge tracking force pressure quoted
by your cartridge manufacturer. This is not critical
Note
Note
Note
NoteNote:
:
:
: :
and a figure between 1.5 & 2.0 will normally be suitable
for most moving magnet cartridges.
Your arm is now balanced, setup and ready to use. If
you have any doubts regarding installation or setup
please contact your official Rega dealer who will be
able to carry out the work for you. Thank you for
purchasing this Rega product and we wish you many
hours of musical enjoyment.
www
www
www
wwwwww.r
.r
.r
.r.rega.co.uk
ega.co.uk
ega.co.uk
ega.co.ukega.co.uk
Made in England
RB
RB
RB
RBRB330
330
330
330 330 T
T
T
TTONEARM
ONEARM
ONEARM
ONEARMONEARM
Protractor &
arm mounting
data included.
Cueing
Platform
Tracking
Dial
Headshell
Finger lift
Arm Clip
Cueing device
lift/lower handle
Balance
Weight
2
1
0
Bias adjustment
Fitting your Tonearm
Fitting your Tonearm
Fitting your Tonearm
Fitting your Tonearm Fitting your Tonearm
The will directly replace any other Rega tonearm
RB330
RB330
RB330
RB330 RB330
that currently uses the 3 point mounting without any
modification. If fitting to another manufacturers
product or an older Rega turntable (with the single
point nut fixing), the supplied template should be used
as a guide to ensure correct position and alignment.
With so many variants in turntable models it is important
to contact your turntable manufacturer if in any doubt
before making any holes in plinths or arm boards.
Before attempting to fit the arm to the turntable,
RB
RB
RB
RBRB330
330
330
330 330
it is important to ensure that there is sufficient
clearance beneath the turntable and that the arm
does not hit the lid, top or sides. Having checked that
there is sufficient clearance in all directions (including
the maximum potential arm movement horizontal and
vertical) the next step is to find the position of the
centre of the arm mounting hole. The easiest way to do
this will be to use the arm mounting template supplied.
Arm mounting temp
Arm mounting temp
Arm mounting temp
Arm mounting tempArm mounting template guide
late guide
late guide
late guidelate guide
The supplied template is for mounting Rega three point
fixing arms to other manufacturers turntables. N.B
protractor for cartridge alignment is also printed on
the same template.
1.
1.
1.
1. 1. The template should be kept flat and not bent. The
distance between the centre of the spindle and the
centre of the arm hole is critical and must be 222mm.
This template will help you check your positioning
before you attempt fitting and drilling.
3.
3.
3.
3. 3. Position the other end of the template so that the
clearance arc is within the rear and side edges of the
turntable base (and the lid when closed). Also check
that there is at least 250mm clearance from the centre
of the hole to the inside front of the turntable.
4.
4.
4.
4. 4. Use a long pointed probe such as a needle and
push it through the arm hole centre on the template. ‘ ’
Keep the needle perpendicular to the template and
mark the position of centre on the turntable.
5.
5.
5.
5. 5. Having marked the centre, check again that if the
arm is placed in this position it will clear the under side
of the turntable and the lid. Also, check that the arm is
in a satisfactory position to ensure easy operation and
that the position is pleasing aesthetically. When you are
certain that the arm hole centre is in its correct position
(exactly 222mm from the record centre), you can drill
the required arm hole.
6.
6.
6.
6. 6. The arm mounting pillar requires a diameter of 25mm
which will provide adequate clearance for accurate
fitting. You can then drill the three screw mounting
holes as illustrated on the template. Make sure the arm
is straight and the holes are correctly aligned before
drilling.
7.
7.
7.
7. 7. With the holes drilled, you are now ready to fit the
arm to the turntable. Ensure that you also follow the
turntable manufacturer s instructions regarding arm ’
fitting. Each individual turntable manufacturer may
have different requirements regarding positioning of
the arm signal lead.
RB330 Instructions

Especificaciones del producto

Marca: Rega
Categoría: No categorizado
Modelo: RB330

¿Necesitas ayuda?

Si necesitas ayuda con Rega RB330 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Rega Manuales

Rega

Rega ND5 Manual de Usario

26 Septiembre 2024
Rega

Rega Atlas MK2 Manual de Usario

19 Septiembre 2024
Rega

Rega Fono Mini A2D MK2 Manual de Usario

19 Septiembre 2024
Rega

Rega Nd3 Manual de Usario

16 Septiembre 2024
Rega

Rega Fono MM MK5 Manual de Usario

14 Septiembre 2024
Rega

Rega Fono MC MK4 Manual de Usario

14 Septiembre 2024
Rega

Rega Aura MC Manual de Usario

13 Septiembre 2024
Rega

Rega Aria MK3 Manual de Usario

13 Septiembre 2024
Rega

Rega Carbon Manual de Usario

13 Septiembre 2024
Rega

Rega RB78 Manual de Usario

13 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024