Roberts Radio Revival iStream 3L Manual de Usario

Roberts Radio Radio Revival iStream 3L

Lee a continuación 📖 el manual en español para Roberts Radio Revival iStream 3L (3 páginas) en la categoría Radio. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

To listen to internet radio or to stream music, your radio must rst be connected to your network.

1 Choose ‘YES’ to keep the radio connected to the network when

in Standby. This will allow remote control software to switch on

your radio when needed.

2 A list of the available WiFi networks will then be displayed. If

no networks are found then your radio may be too far from your

router.

3 Rotate the Tuning control to navigate the list of available

networks and highlight your own Network Name. If your Network

Name is not found, then you may have to get your wireless router

working or your radio may be too far from the router.

4 If your Network Name (sometimes called SSID) is displayed with

“[WPS]” (WiFi Protected Setup), then press the Tuning control

and a WPS menu will be displayed, otherwise press the Tuning

control and proceed to step 6.

5 Choose one of the WPS menu options as required for your router

(WPS may be via push button, or using an identication number):

‘Push Button’ - the display prompts you to press the WPS button

on your router and then the Tuning control on the radio. The two

devices should then connect automatically. Proceed to step 9.

‘PIN’ - the display shows an identication number which you must

enter into your router using a web browser (refer to your router’s

user documentation). You should then press the Tuning control

on the radio. Proceed to step 9.

‘Skip WPS’ – if you wish to enter your password or if your

password was previously entered.

6 If you are prompted to enter a password (or key), enter each

character by rotating the control to highlight it, then Tuning

pressing the control. If you are not prompted for a Tuning

password then proceed to step 9.

7 The three controls on the right-hand side of the password key

screen have special functions. You can quickly access these by

pressing the button and then using the Info Tuning control as

needed.

Select ‘OK’ - When the complete password has been entered.

Select ‘BKSP’ - Select to erase a character (long press to clear).

Select ‘CANCEL’ - To cancel and re-run the Network Wizard.

8 After the nal character of the password has been entered,

highlight the symbol and press the control. ‘OK’ Tuning

9 The screen will show ‘Connecting..’ and then ‘Setup wizard

completed’. Press the control to exit the setup wizard. Tuning

The radio should now be able to connect to the network. Your

radio will display the Main mode menu.

10 For details on navigation and operation of your smart radio,

please see overleaf.

Smart radio, mains adaptor, quick start guide, safety/warranty and streaming service leaet. Please visit

www.robertsradio.com if you wish to download the full user guide.

Features

Controls

continued overleaf...

STEP 1 - Connect to the mains & setup your smart radioWhat is in the Box?

E - Connect to your network

F - Use the UNDOK app to setup your radio

• DAB / DAB+ / FM and WiFi internet radio with colour display and built-in battery charging

• Stream using Spotify Connect, Deezer and Amazon Prime music

(Third-party streaming services may require a subscription)

• Bluetooth audio streaming from iPhone or Smartphone

• MP3 playback via USB

• Full control via the UNDOK smartphone app (for Apple iOS and Android)

• 60 presets (40 x Internet Radio/Podcast, 10 x DAB, 10 x FM)

• Wireless connection (Dual-band WiFi, 802.11b/g/n/a)

• 6 equaliser proles and separate bass and treble

• 2 alarm timers (DAB/FM/Internet or buzzer)

• USB charging of smartphone, tablet or similar devices

• AC adaptor included / Batteries 6 x LR6/AA size or rechargeable equivalent (not included)

• Stereo auxiliary input, line out and headphone sockets

A - Connect to the mains

Please read the safety leaet provided before connecting your radio to the mains.

1 Place your radio on a at surface.

2 Plug the cable from the mains adaptor into the .DC input socket

3 Plug the mains adaptor into a wall socket and switch on the socket.

4 The display on the radio will show a start up screen for a few seconds.

If this is the rst time that you use your radio (or after a Factory Reset)

the display will show the language menu.

Line

Out

1 If you wish to setup your radio using the UNDOK app download

and install the UNDOK app on to your Android or iOS device.

2 Follow the on-screen instructions or see the full user guide

on-line.

• If you already have the UNDOK app installed on your device

ensure that you have the latest version.

1 Charge / Low battery indicator

2 On/Off / Volume control

3 Headphone socket

4 Auxiliary input socket

5 USB playback / Charge socket

6 Mode / Bluetooth pair button

7 Menu button

8 Info button

9 LCD display

10 Preset / Play / Pause button

11 Previous button

12 Next button

13 Alarm / Sleep button

14 Telescopic aerial

15 Tuning / Select / Snooze control

16 Bluetooth indicator

17 Loudspeaker

18 WiFi antenna (internal)

19 DC input socket

20 Line output socket

21 Battery compartment

22 Battery charge switch (inside compartment)

Before you can use your smart radio you must have the following:

• A broadband internet connection (not required for DAB, FM or music player functions).

• A router (or wireless access point) providing a WiFi signal, connected to your broadband internet

service provider.

• A Smartphone or tablet which uses the Android operating system (version 4.0.3 or later) or Apple

iOS (version 9 or later).

• If your wireless network requires a security password, then you will need to have this available during

setup. The radios WiFi system is compatible with 802.11b, g, n or a networks and can use 2.4GHz or

5 GHz WiFi frequency bands.

IMPORTANT: Before you continue, make sure your router is powered up and working with your

broadband internet service provider.

D - Select clock and time settings

1 The radio will show a setup wizard. With highlighted press ‘YES’

the Tuning/Select control to begin setting up your radio.

• Note: If you wish to go back within a menu or if you make an error

at any time, please use the button.Menu

2 Choose either the or12 24 hour clock display.

3 A menu allowing you to specify the auto-update option for the clock

will be shown. Update from network will be the best for most users.

4 Choose the timezone for your region.

5 Choose a daylight saving option. This is also known as Summer/

Winter time (or BST/GMT in the UK).

C - Select language

By default your radio will display all menus and messages in English.

1 Rotate the Tuning/Select control to highlight the desired language.

2 Press the control to enter the selection.Tuning/Select

• Your radio will display a privacy policy. Please read the privacy policy

and then press the control to accept the policy.Tuning/Select

Jones family

[WPS] Paul’s network

Smith

Brown

[Rescan]

[Manual config]

SSID

Network settings

Keep network connected?

Network settings

Network wizard

Scanning...

Push Button

Skip WPS

WPS Menu

Key:

0 1 2 3 4 5 6

7 8 9 . _ - @

, a b c d e

f g h i j k l

m n o p q r s

123-jones

Setup wizard

completed

Press ‘SELECT’ to exit

Network settings

Please wait

Connecting...

English

Dansk

Nederlands

Français

Deutsch

Italiano

Language

Your radio may be congured using either the display and buttons on

the radio or using the UNDOK app. First-time users are recommended

to use the radio’s controls.

1 If you wish to use to setup your radio, UNDOK skip to step F now.

2 If you would like to setup your radio using the radio’s controls follow

the setup procedure below and choose the desired language.

B - Setup using the radio or the UNDOK app

Setup wizard

Start now?

Date/Time

12/24 hour format

Auto update

Update from DAB

Update from FM

Update from Network

No update *

Line

Out

Internet/DAB / DAB+ / FM RDS / Bluetooth

USB Smart Radio

WiFi: 2.4GHz / 5GHz

FM: 87.5-108MHz

DAB/DAB+ (BAND III): 5A-13F

DC In: 12V 1.5A

USB Output: 5V 1A

Battery: 6x 1.5V AA

Designed & Engineered in the UK, Made in China

Roberts Radio Ltd,

Stoney Lane, Whiston,

Prescot, L35 2XW, UK

Glen Dimplex Europe Ltd,

Airport Road, Cloghran,

Co. Dublin, K67 VE08, Ireland

READ SAFETY GUIDE

iStream3L

Mode

Aux In

Preset

Sleep

Snooze

Low Battery

Charge/

Low Battery

19 20

Snooze

Use restriction:This device

is authorised in the following

countries for indoor use only

when used with 5GHz Wi-Fi (5150

to 5350MHz; channels 36 to 64):

AT BE BG CY DECH CZ

DK EE EL ES FI FR HR

HU IE IS IT LI LULT

LV MT NL NO PL PT RO

RS TRSE SI SK UK(NI)

Battery operation (Alkaline) **

1 Slide the battery cover located underneath the unit in the direction

of the arrow and lift upwards.

2 Slide the switch inside the battery compartment to the Alkaline

position (as shown) and insert six LR6 (AA size) alkaline batteries.

Take care to ensure all batteries are inserted with the correct polarity

as shown on the battery compartment cover. Then replace the

battery cover. Important: when using alkaline batteries the battery switch

must be placed in the alkaline position. Failure to do so could result in

serious damage to the batteries or radio.

If no batteries are tted then set the switch to the Alkaline position. This minimises

the power consumption when the radio is powered from the mains.

Battery operation (Rechargeable) **

1 Slide the switch inside the battery compartment to the NiMH position

(as shown).

2 Insert six identical Rechargeable LR6 (AA size) batteries. Then

replace the cover. The radio is designed to be used with Nickel

Metal Hydride (NiMH) rechargeable batteries. No other type of

rechargeable battery should be used in the radio.

3 Plug the mains adaptor into your radio and then plug the adaptor into the mains.

The battery indicator will ash green indicating the batteries are charging.

The display will show the status of battery charging . The batteries will

be fully charged in 5 - 7 hours. Under some conditions the charging indicator

may switch off after ashing only briey. This may happen if the batteries are

already freshly charged, or if the radio detects that you may be attempting to

recharge alkaline batteries. In these cases the charging will be stopped.

4 When charging is completed the charging indicator will show a steady green

and a green ‘Battery Full’ indicator will be displayed. If the charge process stops

after a short while this may be due to a faulty battery. In this case the charging

indicator will show red and a red ‘Battery Fail’ indicator will be displayed. You

can then press the Info button to show the individual battery status. The faulty

battery will be marked with a red cross.

Note: Never mix alkaline and rechargeable batteries.

STEP 2 - Navigating your smart radio

STEP 3 - Operating your smart radio

Other information

Circuit features

Bluetooth

1 Ensure is enabled on your smart device.Bluetooth

2 Press to select Bluetooth mode on your radio.Mode

3 The Bluetooth indicator will ash blue and your radio will show

that it is ‘discoverable’. On your smart device select ‘iStream 3L’.

Once the connection is established the indicator will remain

steady. You may now play your music.

4 To connect a different device apply a long press on the

Mode / Bluetooth Pair button. Your radio will become

discoverable by other devices. **

ROBERTS RADIO LIMITED

www.robertsradio.com

Issue 1

2021-11-26

Smart Radio with Bluetooth, USB and Streaming Services

and remote control from iPhone and Android using UNDOK

Please read this guide, safety/warranty and streaming leaet before use

iStream 3L

Specications

Power requirements

Mains (adaptor): 100 - 240V 50/60Hz

Batteries 6 x LR6 (AA size) Alkaline or NiMH rechargeable (not included)

Battery life Between 8 and 10 hours using alkaline cells **

Connectivity

WiFi 802.11 b, g, n or a supported with WEP and WPA / WPA2 encryption

Headphone socket 3.5mm dia. stereo

Aux In socket 3.5mm dia. stereo

Line out socket 3.5mm dia. stereo

Aerial System WiFi Built-in antenna, DAB/FM Telescopic aerial

Bluetooth standards A2DP, AVRCP, Bluetooth codecs supported SBC

Bluetooth EIRP POWER (MAX.) 10.26dBm

Frequency coverage FM 87.5 - 108MHz, DAB 174.928 - 239.200MHz

Bluetooth 4.2 frequencies 2.402 - 2.480GHz

Product markings

DC Power input 12V / 1.5A USB output 5V /1A

This symbol indicates AC voltage. This symbol indicates DC voltage.

Mains adaptor

Manufacturer of AC Adaptor: Hung Kay, Model: PU 82, Input voltage: AC100 -

240V, Input AC frequency: 50/60Hz, Output voltage: DC12.0V, Output current:

1.5A, Output power: 18.0W, Average active efciency:

88.72%, Efciency at

low load (10%) 85.26%, No-load power consumption: < 0.1W

Please handle with care. The leather-cloth nish may be susceptible to damage

if mistreated. Avoid all contact with any abrasive material, chemical substances

or cleaning solutions. Your radio may be wiped with a clean lightly damp cloth.

Please ensure that the product is unplugged from the mains socket outlet

before attempting this procedure.

Battery operation

Internet radio - Listen to internet radio

Podcasts - Listen to Podcasts

DAB radio - Listen to DAB radio

FM radio - Listen to FM radio

Auxiliary input - Connect to other devices

Spotify - Play music from Spotify

Amazon Music - Play music from Amazon Music

Deezer - Play music from Deezer

Bluetooth - Stream music using your smart device

USB - Play music from USB memory device

System reset

If you wish to completely reset your radio to its

initial state perform a factory reset. Press . Menu

Choose , ‘System settings’ ‘Factory reset’ then

‘YES’. All user entered settings will be erased.

Media playback controls

Control media playback using the play/pause, previous and next

buttons. : These features are dependent on the music being Note

played and will not always be available. **

System settings

You can access your radios ‘System settings’ from the current menu. The system settings include

Equaliser, Streaming audio quality, Network, Time/Date, Brightness, Inactive Standby, Language,

Factory reset, Software update, Setup wizard, Info and privacy policy. **

Your radio has 40 memory presets for

Internet Radio / Podcasts,10 DAB and

10 for FM which can easily be set to

store a radio station or (for internet radio

a podcast).**

1 Tune to the required radio station.

Apply a long press on the Preset

button will be ‘Save to Preset’

displayed. Use the Tuning control

to scroll to an unused preset or a

preset you wish to change. Press

Tuning to store.

2 To recall a preset station, choose

internet, Podcast, DAB or FM mode.

Give a short press on the Preset

button will be ‘Recall from Preset’

displayed. Use the Tuning control

to select the desired preset station.

Preset radio stations

Play Internet, DAB or FM radio

USB

Stream your music collection from a USB memory device.

1 Choose ‘USB playback’ to playback a USB memory device. The USB socket can

also be used to charge your smartphone, tablet or similar devices. **

Internet - You can search for a radio station or podcast by location, genre or by the

station name. You can also store preset stations or add a station to your favourites list. **

DAB - Carefully, extend the telescopic aerial. A scan of the Band III DAB channels

will be carried out. Rotate the Tuning control to access the full station list. Press the

Tuning control to select the highlighted radio station. **

FM - Extend the telescopic aerial. Rotate the Tuning control clockwise or anti-clockwise

and then press the control to scan low to high or high to low frequency. **Tuning

In this guide the symbol ** indicates that further details are provided in the on-line user guide available from www.robertsradio.com

A short press will switch your radio On or to Standby. **

A short press will cancel an active alarm.

Rotate to adjust the volume level.

A short press will access each operating mode in turn.

A long press will disconnect a Bluetooth device when in Bluetooth mode.

A short press will access the current menu system.

Press the Menu button to go back to a higher level menu or if an error is made.

Rotate clockwise or anti-clockwise to scroll menu items.

A short press on Tuning/Select will select highlighted menu items.

A short press on Tuning/Select will access snooze when an alarm sounds.**

A short press will display information relating to the music being played.

A long press will access the brightness settings.

A short press will change alarm status when the unit is in standby. **

A long press will access alarm settings when the unit is in standby. **

A short press will access alarm settings when the unit is playing. **

A long press will access the sleep timer when the unit is playing. **

1 Switch on your radio.

2 Pressing gives you access to each of the operating Mode

modes in turn.

3 Alternatively press Mode Tuning and rotate the control

clockwise or anti-clockwise to highlight the desired menu

item and then press the select control to select that item.

4 Press Menu to access the full menu for the current operating

mode.

Select music mode In order to minimise its energy consumption when not in use, your radio will go

into standby if it detects that it is no longer being used.** By default this period

is set to 8 hours but you may change it if you wish. With your radio switched

on, press Menu, choose then and then ‘System settings’ ‘Inactive Standby’

choose from 2, 4, 6, 8 hours or Off. Your radio will go into standby after the

selected time has expired.

Compatible with 2.4 GHz and 5 GHz WiFi bands.

5 GHz Wi-Fi function: 5150 - 5350MHz, 5470 - 5725MHz and 5725 - 5875MHz

The name plate is located underneath the radio.

The company reserves the right to amend the specication without notice.

Designed & Engineered in the UK

Made in China

Please read the safety leaet provided

before using batteries. Note: You should never attempt to recharge alkaline batteries in the radio.

Attempted recharging of alkaline batteries can be dangerous.

• Important: when using rechargeable batteries the battery switch must

be placed in the NiMH position. Batteries will only be charged when

the radio is switched off and connected to the AC adaptor.

• When the batteries are exhausted, the low battery indicator will show red

for a short while. The radio will then switch itself off. It may not be possible

to switch the radio back on until the batteries are recharged, or until the

radio is connected to the mains adaptor.

• If the radio is not to be used for any extended period of time it is recommended

that the batteries are removed from the radio.

For further details on the use of rechargeable batteries please see full

user guide on-line. Replace batteries only with the same or Caution:

equivalent type. Danger of explosion if the batteries are incorrectly replaced.

Snooze

Mode

Sleep

2.4GHz WiFi EIRP POWER (MAX.) 19.76dBm

5GHz WiFi EIRP POWER (MAX.) 18.89dBm

Especificaciones del producto

Marca:	Roberts
Categoría:	Radio
Modelo:	Radio Revival iStream 3L

¿Necesitas ayuda?

Si necesitas ayuda con Roberts Radio Revival iStream 3L haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Radio Roberts Manuales

Roberts Rambler Max Manual de Usario

24 Octubre 2024

Roberts Stream 93i Manual de Usario

13 Octubre 2024

Roberts Duet 2 Manual de Usario

5 Octubre 2024

Roberts Colourstream Manual de Usario

29 Septiembre 2024

Roberts Revival Icon Manual de Usario

15 Septiembre 2024

Roberts Revival Petite 2 Manual de Usario

12 Septiembre 2024

Roberts Stream 218 Manual de Usario

27 Agosto 2024

Roberts Blutune 200 Manual de Usario

10 Agosto 2024

Roberts Revival Mini Manual de Usario

9 Agosto 2024

Roberts Radio Revival iStream 3L Manual de Usario

5 Agosto 2024

Radio Manuales

Últimos Radio Manuales

Hyundai TRC 533 AU3BS Manual de Usario

27 Octubre 2024

Tangent DAB2GO+ Manual de Usario

26 Octubre 2024

Xiaomi Mi Internet Radio Manual de Usario

24 Octubre 2024

Sven SRP-50 Manual de Usario

24 Octubre 2024

Yamazen JYTM-RTV430 Manual de Usario

23 Octubre 2024

Philips AE5020 Manual de Usario

22 Octubre 2024

Albrecht DR-330 Manual de Usario

20 Octubre 2024

Argon DAB4 plus Manual de Usario

20 Octubre 2024

Argon DAB2 plus Batt Manual de Usario

19 Octubre 2024

PerfectPro RockHart BT Manual de Usario

19 Octubre 2024