Rosieres RVI 740 IN Manual de Usario

Rosieres horno RVI 740 IN

Lee a continuación 📖 el manual en español para Rosieres RVI 740 IN (14 páginas) en la categoría horno. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/14

USINES DE ROSIÈRES - 30, rue Y. LACELLE - Rosières - 18400 - Lunery - France

NOTICE D'EMPLOI ET D'INSTALLATION

TABLE À INDUCTION

INSTRUCTIONS FOR USE AND INSTALLATION

INDUCTION HOBS

1 GB

READ THE INSTRUCTIONS BOOKLET CAREFULLY TO MAKE THE MOST OF YOUR HOB.

We recommend you keep the instructions for installation and use for later reference, and before installing the hob, note its serial number

below in case you need to get help from the after sales service.

We are constantly striving to improve product quality and as such may modify appliances to incorporate the latest technical improvements.

Induction hobs conform to directives 73/23/CEE and 89/336/CEE.

Identification plate

(located under the hob's bottom casing)

• It is strongly recommended to keep children away from the cooking zones while they are in operation or when they are switched off,

so long as the residual heat indicator is on, in order to prevent the risks of serious burns.

• When cooking with fats or oils, take care always to watch the cooking process as heated fats and oils can catch fire rapidly.

• The hob’s control area is sensitive, do not place hot containers on it.

• Aluminium foil and plastic pans must not be placed on heating zones.

• After every use, some cleaning of the hob is necessary to prevent the build up of dirt and grease. If left, this is recooked when the

hob is used and burns giving off smoke and unpleasant smells, not to mention the risks of fire propagation.

• Do not left metallic objects such as knives, forks, spoons or lids on the induction zone,because if they are too large or too heavy, they

could become hot.

• Never cook food directly on the glass ceramic hob. Always use the appropriate cookware.

• Always place the pan in the centre of the unit that you are cooking on.

• Do not use the surface as a cutting board.

• Do not slide cookware across the hob.

• Do not store heavy items above the hob. If they drop onto the hob, they may cause damage.

• Do not use the hob as a working surface.

• Do not use the hob for storage of any items.

• In the unlikely event of a surface crack appearing, do not use the hob. Immediately disconnect the hob from the electrical power supply

and call the After Sales Service.

Warning: this appliance complies with current safety regulations and electromagnetic compatibility regulations. Nevertheless,

people with a pacemaker should not use this appliance. It is impossible to guarantee that all such devices found on the market

comply with current safety regulations and electromagnetic compatibility regulations, and that dangerous interference will not

occur. It is also possible that people with other types of device, such as a hearing aid, could experience some discomfort.

GENERAL WARNINGS

574 x 505 x 55 574 x 505 x 55 752 x 505 x 55 574 x 505 x 55

Installing a domestic appliance can be a complicated operation which if not carried out correctly, can seriously affect consumer

safety. It is for this reason that the task should be undertaken by a professionally qualified person who will carry it out in

accordance with the technical regulations in force. In the event that this advice is ignored and the installation is carried out

by an unqualified person, the manufacturer declines all responsibility for any technical failure of the product whether or not

it results in damage to goods or injury to individuals.

2 GB

BUILT-IN

The furniture in which your hob will be installed and all adjacent

furniture, should be made from materials that can withstand high

temperatures. In addition, all decorative laminates should be fixed

with heat-resistant glue.

Installation:

• A watertight seal is supplied with the hob.

Before fitting:

- turn the hob upside down, with the glass surface facing downwards.

Make sure the glass is protected.

- fit the seal round the hob.

- make sure that it is correctly fitted to avoid any leakage into the

supporting cabinet.

• It it important to fit the hob on a level supporting surface.

• Deformations caused by incorrect fitting can alter the specifications

of the worktop and the performance of the hob.

• Leave a gap of at least 5 cm between the appliance and any

neighbouring vertical surfaces.

• It is absolutely essential that the recess conforms with the

dimensions indicated.

• The height of the flush-mounted part of the hob is 5,5 cm.

• If there is an intermediate division :

- the clearance between the bottom of the casing and an

intermediate floor or part of a furniture unit must greater than

2,5 cm so as to allow air circulate.

The minimum distance should be 8 cm.

- furthermore, you should ensure that there is at the rear a

ventilation (8 cm) on all the width.

• You can not build the hob in above an oven with no fan, a

dishwasher, fridge, freezer or washing machine.

• The body of the hob is fitted which 4 location holes to take the

fixing clamps intended to fix the hob in the unit. Place the 4 fixing

clamps, before building-in the hob, in such a way that the hob

is placed perfectly in the support unit.

INSTALLATION

• The yellow/green wire of the power supply cable must be

connected to the earth of both power supply and appliance

terminals.

• The manufacturer cannot be held responsible for any accidents

resulting from the use of an appliance which is not connected

to earth, or with a faulty earth connection continuity.

• Any queries regarding the power supply cord should be referred

to After Sales Service or a qualified technician.

The hob is fitted with a power supply cord which allows it to

be connected only to a power supply of 220-240 V between

phases or between phase and neutral.

• Connect to a socket, to choose the correct fuse, you must refer

on the table.

It is however possible to connect the hob to :

Two phases 220-240V2~, Threephases 220-240V3~

or Three phases 380-415V3N~.

To proceed to the new connection, you must adhere the following

instructions.

• Before making the connection make sure that the installation is

protected by a suitable fuse, see table, and that it is fitted with

wires of a large enough section to supply the appliance normally.

1- Operations to be carried out on the existing connection :

- turn over the hob, glass side against the work top, taking care

to protect the glass.

- open the cover.

- pull out the supply cord :

. remove the screws retaining the shunt bars and the conductors

of the supply cord,

. unscrew he cable clamp to release the power supplying cord,

. pull out the supply cord.

2- Operations to be carried out to make a new connection :

- choose the power supply cord in accordance with the

recommendations in the table.

- pass the power supply cable into the clamp.

- strip the end of each conductor of the supply cord on a 10 mm

length, by taking in account the requested length of the cord for

the connection to the terminal block.

- according to the installation and with the help of shunt bars which

you should have recovered in the first operation, fix the conductor

as shown on the chart.

- screw the cable clamp and fix the cover.

Seal

Hob

25 mm

mini

50 mm

Opening

500 X 50

Opening

500 X 10

CONNECTION TO THE TERMINALS ON THE TERMINAL BLOCK:

"The installation must conform to the standard directives."

The manufacturer declines all responsibility for any damage that

may be caused by unsuitable or unreasonable use.

Warning :

• Always check before any electrical operation, the supply tension

shown on the electricity meter, the adjustment of the circuit-

breaker, the continuity of the connection to earth to the installation

and that the fuse is suitable.

• The electrical connection to the installation should be made via

a socket with a plug with earth, or via an omnipole cut-out switch

with an opening gap of at least 3 mm.

If the appliance has a socket outlet, it must be installed so that

the socket outlet is accessible.

ELECTRICAL CONNECTION

Especificaciones del producto

Marca:	Rosieres
Categoría:	horno
Modelo:	RVI 740 IN

¿Necesitas ayuda?

Si necesitas ayuda con Rosieres RVI 740 IN haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

horno Rosieres Manuales

Rosieres RFI 4352 IN Manual de Usario

18 Octubre 2024

Rosieres RTG 75 WFB RB Manual de Usario

17 Octubre 2024

Rosieres BG 710 RB Manual de Usario

9 Octubre 2024

Rosieres RFN 6552 IN Manual de Usario

8 Octubre 2024

Rosieres RVE 632 Manual de Usario

8 Octubre 2024

Rosieres F 453 Manual de Usario

5 Octubre 2024

Rosieres RFA 24 PN Manual de Usario

4 Octubre 2024

Rosieres BM 571 RU Manual de Usario

4 Octubre 2024

Rosieres RFL54GVIN/1 Manual de Usario

4 Octubre 2024

Rosieres RFS 6871 IN/E Manual de Usario

3 Octubre 2024

horno Manuales

Últimos horno Manuales

Continental Edison CECM6065W Manual de Usario

27 Octubre 2024

Taurus HM778WHD Manual de Usario

27 Octubre 2024

Lacanche CITEAUX Manual de Usario

27 Octubre 2024

JennAir JDS1450FS Manual de Usario

27 Octubre 2024

Orima ORP-76-IN Manual de Usario

27 Octubre 2024

Breville the Handy Hot Plate BHP150 Manual de Usario

27 Octubre 2024

JennAir JGRP436HL Manual de Usario

27 Octubre 2024

Neff C17MS22G1 Manual de Usario

27 Octubre 2024

Pit Boss BK24 Manual de Usario

27 Octubre 2024

Guzzanti GZ-8206 Manual de Usario

27 Octubre 2024