Rowenta Pro Precision DG 7140 Manual de Usario
Lee a continuación 📖 el manual en español para Rowenta Pro Precision DG 7140 (2 páginas) en la categoría Hierro. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
Fill the boiler :
1. Place your steam generator on a stable, horizontal
heat-resistant surface.
2. Ensure that your appliance is disconnected and cold.
3. Unscrew the boiler screw cap.
4. Using a water jug, fill with one litre of water.
5. Fill the boiler, taking care that
the water does not spill over (1).
If this occurs, remove the excess
water.
6. Replace the boiler screw cap,
screwing on tightly.
ENGLISH
1. UNDERSTANDING YOUR STEAM
GENERATOR
Iron
temperature
control light
Steam output control dial
2. PREPARING YOUR STEAM GENERATOR
3. USING YOUR STEAM GENERATOR
(1)
Be careful :
The first time the appliance is used, there may be some
fumes and smell but this is not harmful.
They will not affect use and will disappear rapidly.
Recommendations:
To prime the steam circuit, either before using the iron for
the first time, or if you have not used the steam function for
a few minutes, press the steam control button several times
in a row, holding the iron away from your clothes.
This will enable any cold water to be removed from the
steam circuit.
• Iron temperature control setting :
- Start with fabrics to be ironed at a low temperature (
●)
and finish with those which need higher temperatures
(●●● or Max).
- Mixed fibre fabrics : set the ironing temperature
to the setting for the most delicate fabric.
- Woollen garments : press repeatedly on the steam control
button to obtain short bursts of steam, without placing
the iron on the garment itself. This will avoid making the
fabric shiny.
• Steam output control dial setting :
- Thick fabric : increase the steam setting.
- At a low temperature : set the steam output control dial
to the low position.
• Dry ironing :
- Do not press the steam control button beneath the iron
handle or the “Precision Steam Jet” button on the iron
handle.
• If you are using starch, it should be sprayed onto
the reverse side of the fabric to be ironed.
• Ironing board :
For best results a mesh type ironing board should be used
to allow any excess steam to escape.
6. VERTICAL STEAM IRONING
1. Set the iron temperature control to the maximum
position.
Set the steam output control dial on the control panel
to the maximum position.
2. Hang the garment on a coat hanger and hold the
fabric slightly taut with one hand.
As steam is very hot, never attempt to remove creases
from a garment while it is being worn, always hang
garments on a coat hanger.
3. Holding the iron in a vertical position,
press repeatedly on the steam
control button (beneath the iron
handle) moving the iron from top
to bottom (9).
5. “PRECISION STEAM JET” FUNCTION
Your generator has a “Precision Steam Jet” function,
allowing you to:
- Iron the most hard-to-reach areas (such as button holes,
shirt cuffs and collars, darts in trousers, the inside of jacket
and coat sleeves);
- Dampen and soften the fibres before ironing, when the
fabric is very creased.
Use:
- With the iron on the ironing board, press the “Precision
Steam Jet” button on the iron handle 2 or 3 times to
obtain short, powerful bursts of steam at the front of the
iron (7);
- Then iron the fabric using steam from the soleplate to
smooth the fibres, by pressing the steam control button
beneath the iron handle (8).
(9)
Recommendations :
For fabrics other than linen or cotton, hold the iron
a few centimetres from the garment to avoid burning
the fabric
INSTRUCTIONS FOR USE
4. STEAM IRONING
During ironing, the temperature control light located
on the iron and the steam indicator will go on and off
according to the temperature control.
047242 - 48/04
Your steam generator has been designed to operate using
untreated tap water. However, if your water is very hard,
mix it 50 % untreated tap water 50 % distilled water.
The water to use in your steam generator :
Types of water to be avoided
Do not use water from clothes dryers, scented water,
water from refrigerators or air conditioners, rain water ;
Also do not use filtered, boiled or bottled mineral water.
These contain organic waste or mineral elements that
become concentrated when heated and cause spitting,
brown staining or premature wear to the appliance.
Use of these types of water will negate the guarantee
provided with the product.
Steam control button
“Precision Steam Jet”nozzle
“Precision Steam Jet”
button
Temperature
control dial for
iron soleplate
Steam indicator
Illuminated On/Off switch
CONTROL PANEL
1. Open the flap to the cord storage compartment by
undoing the catch.
2. Completely remove the cords from the storage
compartment and slot them into the notches on either
side of the flap (2).
3. Close the door.
4. Connect your steam generator to a socket with an earth
connection.
5. Press on the illuminated on/off switch.
The steam indicator lights up while the boiler is
heating up.
When the indicator goes out (after about 7 minutes),
steam is ready.
You can use your appliance and start ironing.
(2)
(3)
c
o
t
t
o
n
-
l
i
n
e
n
s
i
l
k
-
w
o
o
l
s
y
n
t
h
e
t
i
c
s
M
I
N
(4)
Boiler screw
cap
Boiler unit /
water tank
Base unit power cord
Control panel
Iron rest plate
Connection cord
to the boiler unit /
water tank
Flap to cord storage
compartment
2. The iron temperature control light turns on.
Be careful: the generator and the iron are ready to use
when both the iron’s thermostat light and the “steam
ready” indicator go out.
If necessary, also adjust the steam output (steam output
control dial on the control panel) (5), eg : less steam for
low temperatures.
3. To obtain steam, press on the steam control button
beneath the iron handle and keep it pressed (6).
The steam will stop when you release the button.
Note: It is normal for the connection cord to become
warm during use.
Set the temperature and steam output according
to the type of fabric :
1. Place the iron’s temperature control to the setting
suitable for the type of fabric to be ironed (4).
●Synthetics (Low temperature)
●● Silk/Wool (Medium temperature)
●●● Cotton/Linen (High temperature)
With delicate fabrics (
●setting), press the steam control
button (under the handle of the iron) intermittently
to avoid water droplets appearing with the steam.
(5) (6)
Type of
fabric Setting the temperature
control
Setting the steam output
control dial
c
o
t
t
o
n
-
l
i
n
e
n
s
i
l
k
-
w
o
o
l
s
y
n
t
h
e
t
i
c
s
M
I
N
c
o
t
t
o
n
-
l
i
n
e
n
s
i
l
k
-
w
o
o
l
s
y
n
t
h
e
t
i
c
s
M
I
N
c
o
t
t
o
n
-
l
i
n
e
n
s
i
l
k
-
w
o
o
l
s
y
n
t
h
e
t
i
c
s
M
I
N
•
(Low
temperature)
••
(Medium
temperature)
•••
(High
temperature)
Synthetics
Silk /
Wool
Cotton /
Linen
(7) (8)
7. FILLING THE BOILER WHILE IN USE
(when the boiler is empty) • Before cleaning, ensure that the appliance is
unplugged and that the soleplate and the iron rest
have cooled down.
• Do not use any cleaning or descaling products for cleaning
the soleplate or the base unit.
• Never hold the iron or the base unit under the tap.
• Do not place the iron on a metal rest as this could damage it.
Place it on the iron rest on the base unit : it has
non-slip pads and has been designed to withstand high
temperatures.
The Iron soleplate
You can clean the soleplate of your iron, once it has cooled
down, with a damp cloth or sponge.
If the soleplate is badly soiled, we recommend one of
the commercially available specialist cleaning products.
Do not use aggressive or abrasive products for cleaning
the soleplate.
Do not place the iron on a rough support.
During pauses in ironing, always place the iron on the rest
plate provided on the steam generator.
The base unit: Clean the plastic parts occasionally with
a soft cloth.
11. SAFETY INSTRUCTIONS
PROBLEMS
• Water runs through the holes in the
soleplate.
• Droplets of water run through the “Precision
Steam Jet” nozzle.
• White streaks come through the holes in the
soleplate.
• Brown streaks come through the holes
in the soleplate and stain the linen.
• The soleplate is dirty or brown and may stain
the linen.
• There is little or no steam.
• Steam escapes from the boiler cap.
• Steam escapes under the appliance.
POSSIBLE CAUSES
• The boiler is too full.
• Your thermostat is not working :
the temperature is always too low.
• You are using steam before the iron is hot
enough.
• The water has condensed in the pipes because
you are using steam for the first time or you
have not used it for some time.
• The steam output control is set too high for
the temperature set on the iron.
• The soleplate is not hot enough.
• The water has condensed in the pipes because
you are using the “Precision Steam Jet”
function for the first time or you have not used
it for some time.
• Your boiler has a build-up of scale because it is
not rinsed out regularly.
• You are using chemical descaling agents
or additives in the water for ironing.
• Your linen is not rinsed sufficiently or you have
ironed a new garment before washing it.
• You are ironing at too high a temperature.
• You are using starch.
• The boiler is empty.
• The boiler is not yet ready.
• The steam output control dial is set at
minimum.
• Cap screwed on incorrectly.
• The seal on the cap is damaged.
• The equipment is faulty.
SOLUTIONS
• Do not fill the boiler right up to the top.
• Contact an Approved Service Centre.
• Wait for the iron temperature control light
to go out before ironing.
• Press the steam control button away from
your ironing board until the iron produces
steam.
• Decrease the steam output while ironing at
low temperature (steam output control dial on
the control panel).
•
Wait until the soleplate has reached the correct
temperature (iron temperature light goes out).
Press the steam control button (beneath the iron
handle) holding it away from your ironing board,
before activating the
“Precision Steam Jet”
button (on the iron handle).
• Rinse out the boiler after every 10 uses
(see paragraph 9). If your water is hard,
increase the frequency.
• Never add this type of product in the boiler
(see our recommendations regarding water
to be used).
• Ensure linen is rinsed thoroughly to remove
any soap deposits or chemicals on new
garments.
• See our recommendations regarding
temperature control setting.
• Always spray starch onto the reverse side of
the fabric to be ironed.
• Fill the boiler.
•
After switching on, wait for the steam indicator
light to go out (after 7 mins.).
• Increase the steam output (control dial on
the control panel).
• Screw the cap back on.
• Change the cap seal (sachet in the packaging).
• Stop using the generator and contact an
Approved Service Centre.
9. RINSING OUT THE BOILER
Be careful:
To extend the life of your boiler and to avoid any build
up of scale, it is essential that you rinse out the boiler
after every 10 uses. If your water is hard, increase the
frequency.
In particular, do not use descaling agents for rinsing out
the boiler, as they could damage it.
1. Check that the generator is cold and unplugged for
more than 1 hour.
2. With a jug, fill the boiler 3/4 full with tap water.
3. Shake the base unit for a few moments and then empty it
completely over your sink (11).
For best results, we advise
you to repeat this operation.
1. Press the illuminated on/off switch and disconnect the
generator from the mains.
2. Place the iron on the iron rest plate.
3. Place the steam cord and the power cord in the storage
compartment.
4. Leave the iron (and the iron rest) to cool down for
30 minutes.
You can now put your steam generator away.
(11)
HELPLINE:
If you have any product problems or queries with your product,
please telephone our Customer Relations Team on :
0845 602 1454 – UK
(calls charged at local rate)
(01) 4751947 – Ireland
GUARANTEE (U.K. ONLY)
Details of the Rowenta guarantee are shown on
the guarantee card enclosed with the appliance.
This guarantee does not affect your statutory rights.
Should service or further information be required please
contact the Rowenta Customer Relations Department
(see Helpline or enclosed Service Information leaflet).
Do not attempt to dismantle the generator yourself – this
will negate the guarantee.
In line with a policy of continuous product improvement,
Rowenta reserves the right to change product specifications
without prior notice.
Consult our web site :
www.rowenta.co.uk
12. IS THERE A PROBLEM ?
VERY IMPORTANT :
Before opening your boiler, ensure that there is no more
steam left inside by pressing the steam control button
located under the handle of the iron and keep it pressed
until there is no more steam (10).
Never unscrew the boiler cap while the iron is producing
steam.
1. Press the illuminated on/off switch and disconnect the
generator from the mains.
2. Slowly unscrew the boiler cap.
3. Using a water jug, fill with one litre of water.
4. Fill the boiler, taking care that the water does not spill
over.
If this occurs, remove the excess water.
5. Replace the boiler cap, screwing on , reconnect tightly
your steam generator to the mains and switch it on.
6. Wait until the boiler has heated up (approximately
7 minutes).
The generator and the iron are ready to use when both
the iron’s thermostat light and the “steam ready” indicator
go out.
Your appliance contains valuable materials which
can be recovered or recycled.
Â
Leave it at a waste disposal centre.
ENVIRONMENT PROTECTION FIRST !
• Your steam generator is an electrical appliance : It should be used
under normal conditions. It is intended for domestic use only.
• Your generator is fitted with 2 safety systems :
- A boiler closure cap for limiting the pressure. If there is a malfunction,
the cap allows steam to escape ;
- A thermal fuse for preventing any overheating.
• Connect your iron only to alternating current of the voltage specified
on the rating plate and only to a socket with an earth connection.
• This appliance is not intended to be used by children or without
supervision by persons whose physical, sensory or mental aptitude to
use it in complete safety is impaired.
Children must be supervised to ensure that they do not play with the
appliance.
• The appliance must be used and placed on a flat, stable,
heat-resistant surface.
• Always plug your steam generator into :
- An electrical installation with a voltage between 220 V and 240 V.
Connecting to the wrong voltage may cause irreparable damage to
the appliance and will invalidate your guarantee.
- An earthed socket. If you are using a mains extension lead, ensure
that it is correctly rated (10A) with an earth, and is fully extended.
• Should the power cord or the boiler cord linking the iron to the base
unit become damaged, it must be replaced by a ROWENTA Approved
Service Centre to avoid the risk of danger or injury.
Be careful :
• The soleplate and generator iron-rest can become very hot and cause
burns : never touch these parts.
• Your appliance gives off steam which can cause burns.
• Handle your iron carefully, particularly when using the vertical function.
• Do not direct steam at people or animals.
• Take care to ensure that you do not come into contact with electrical
cords with the hot iron soleplate.
• Never leave the appliance unattended :
- when it is connected ;
- until it has cooled down (around 1 hour).
• Never pull the plug out of the socket by the cord.
• Always unplug your appliance :
- before filling or emptying the boiler,
- before cleaning your generator,
- After each use.
• In order to unscrew the boiler cap, always ensure that :
- either your generator is cold (that is, disconnected for over 1 hour) ;
- or there is no more pressure in the boiler (the iron does not
produce any steam when the steam button control is activated).
In all other cases, never attempt to unscrew the boiler cap while the
appliance is in use : the strong steam pressure could cause burns.
Be careful :
If the boiler cap is dropped or severely knocked, have it replaced by
a ROWENTA Approved Service Centre, as it may be damaged.
• Never immerse your steam generator in water or any other liquid.
Never hold it under the water tap.
• While rinsing out the boiler, never fill it directly under the tap.
• The appliance must not be used if it has fallen to the floor, shows
evidence of damage or if it leaks or is not working properly.
Never dismantle your appliance.
To avoid any danger, have it inspected in a ROWENTA approved service centre.
• This product has been designed for domestic use only.
Any professional use, inappropriate use or failure to comply with the
instructions, Rowenta accepts no responsibility and the guarantee will
not apply.
(10)
8.
MAINTAINING YOUR STEAM GENERATOR
10. PUTTING YOUR STEAM GENERATOR
AWAY
Especificaciones del producto
| Marca: | Rowenta |
| Categoría: | Hierro |
| Modelo: | Pro Precision DG 7140 |
¿Necesitas ayuda?
Si necesitas ayuda con Rowenta Pro Precision DG 7140 haz una pregunta a continuación y otros usuarios te responderán
Hierro Rowenta Manuales
7 Octubre 2024
19 Septiembre 2024
18 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
Hierro Manuales
- Hierro Electrolux
- Hierro Bosch
- Hierro AEG
- Hierro Braun
- Hierro Philips
- Hierro Panasonic
- Hierro BEKO
- Hierro Delonghi
- Hierro Grundig
- Hierro Miele
- Hierro Quigg
- Hierro Siemens
- Hierro Zanussi
- Hierro Tefal
- Hierro Adler
- Hierro Alpina
- Hierro Ambiano
- Hierro Ariete
- Hierro Morphy Richards
- Hierro Orbegozo
- Hierro Princess
- Hierro Klarstein
- Hierro Fagor
- Hierro Severin
- Hierro Telefunken
- Hierro Gorenje
- Hierro Silvercrest
- Hierro Nedis
- Hierro Korona
- Hierro Hoover
- Hierro Saturn
- Hierro Black And Decker
- Hierro Tristar
- Hierro Domo
- Hierro Trisa
- Hierro Calor
- Hierro Tomado
- Hierro Livoo
- Hierro OBH Nordica
- Hierro Hyundai
- Hierro Vox
- Hierro Bestron
- Hierro Oster
- Hierro Westinghouse
- Hierro Moulinex
- Hierro Sinbo
- Hierro Izzy
- Hierro Jata
- Hierro Melissa
- Hierro Swan
- Hierro Emerio
- Hierro Scarlett
- Hierro Clatronic
- Hierro Singer
- Hierro Taurus
- Hierro Russell Hobbs
- Hierro Elica
- Hierro Hotpoint
- Hierro Sencor
- Hierro Conair
- Hierro Concept
- Hierro Solac
- Hierro Frigidaire
- Hierro Jura
- Hierro Sunbeam
- Hierro Profilo
- Hierro Aigostar
- Hierro Mellerware
- Hierro Heinner
- Hierro Termozeta
- Hierro Vitek
- Hierro Palson
- Hierro Eldom
- Hierro Jocca
- Hierro Defy
- Hierro Koenic
- Hierro Haier
- Hierro Drew & Cole
- Hierro Beem
- Hierro Exquisit
- Hierro Elba
- Hierro Maxwell
- Hierro Zelmer
- Hierro ETA
- Hierro Qilive
- Hierro Bomann
- Hierro Proficare
- Hierro Hamilton Beach
- Hierro Ufesa
- Hierro Camry
- Hierro Imetec
- Hierro Johnson
- Hierro Nova
- Hierro Koblenz
- Hierro Proctor Silex
- Hierro Primo
- Hierro Tower
- Hierro MPM
- Hierro Konig
- Hierro Becken
- Hierro Laurastar
- Hierro Orion
- Hierro Essentiel B
- Hierro Team
- Hierro Gallet
- Hierro Nevir
- Hierro Kambrook
- Hierro G3 Ferrari
- Hierro Kunft
- Hierro Turmix
- Hierro Easy Home
- Hierro Grunkel
- Hierro Polti
- Hierro Cleanmaxx
- Hierro Coline
- Hierro Elta
- Hierro Cecotec
- Hierro Lelit
- Hierro Weasy
- Hierro Kalorik
- Hierro Orava
- Hierro Di4
- Hierro Khind
- Hierro Domena
- Hierro Duronic
- Hierro Lenoxx
- Hierro Flama
- Hierro LERAN
- Hierro High One
- Hierro Robinhood
- Hierro LAFE
- Hierro Create
- Hierro Girmi
- Hierro JML
- Hierro Vanguard
- Hierro DPM
- Hierro Maxim
- Hierro Brentwood
- Hierro Hacienda
- Hierro Imarflex
- Hierro Yamazen
Últimos Hierro Manuales
24 Octubre 2024
24 Octubre 2024
23 Octubre 2024
23 Octubre 2024
21 Octubre 2024
19 Octubre 2024
18 Octubre 2024
17 Octubre 2024
17 Octubre 2024
15 Octubre 2024