Samsung UN32FH4005H Manual de Usario

Samsung No categorizado UN32FH4005H

Lee a continuación 📖 el manual en español para Samsung UN32FH4005H (2 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
Connections
yFor the best picture and audio quality, connect digital devices using
an HDMI cable.
yIf you connect an external device to the TV that uses an older version
of HDMI, the video and audio may not work. If this occurs, ask the
manufacturer of the device about the HDMI version and, if it is out of
date, request an upgrade.
yBe sure to purchase a certified HDMI cable. Otherwise, the picture
may not display or a connection error may occur.
yConnecting through the HDMI cable may not be supported
depending on the PC.
yFor Set-top box connection using HDMI cable, we highly
recommend you to connect the port.HDMI IN (STB)
Getting Started
Accessories
Input Cables (Sold Separately)
yAudio
yComposite (AV)
yComponent
yCoaxial (RF)
yHDMI
✎Make sure you have the correct cable before plugging it in. Illustrations of common plugs and jacks are shown below.
Cable Plugs Ports/Jacks Do not plug in opposite or wrong direction. It could
damage the TV port.
HDMI
USB
Do not plug cables in upside down. Be sure to check the orientation
of the plug before plugging it in.
TV Controller (Panel Key)
The TV’s Controller, a small joy stick like button on the bottom right side of the TV, lets you control the TV without the remote control.
Remote control sensor TV Controller
The image is drawn by facing
the front side of the TV.
Function menu
m R s
P
Return
Selecting the Media Play
Selecting a Source
Power Off
Selecting the Menu
✎Exits the menu when pressing the controller more than 1 second.
✎When selecting the function by moving the controller to the up/down/left/right directions, be sure not to press the controller. If you press it first,
you cannot operate it to move the up/down/left/right directions.
Plug & Play (Initial Setup)
When you turn the TV on for the first time, a sequence of screens and on-screen prompts will assist you in configuring the TV’s basic settings. Press
the button. is available only when the Input source is set to TV. Set the initial setup following instructions that the TV guides.POWER Plug & Play
✎Connecting the power cord and antenna. (refer to ‘Connections’)
Remote Control
✎This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually impaired persons.
Channel Menu
Seeing Channels
Channel List
Add, delete or set Favorite channels and use the program guide for
digital broadcasts. Select a channel in the , All Channels Added
Channels Favorite Programmed, or screen by pressing the ▲/▼
buttons, and pressing the ENTER
E
button. Then you can watch the
selected channel.
■
All Channels: Shows all currently available channels.
■
Added Channels: Shows all added channels.
■*
Favorite: Shows all favorite channels.
■
Programmed: Shows all currently reserved programs.
✎Using the remote control buttons with the Channel List
xGreen ( ): Enlarges or shrinks a channel number.Zoom
xYellow ( ): Selects multiple channel lists. Select desired Select
channels and press the Yellow button to set all the selected
channels at the same time. The
c
mark appears to the left of
the selected channels.
x
T
(Tools Channel List): Displays the option menu. (The Options
menus may differ depending on the situation.)
Channel Status Display icons
y
c
: A channel selected.
y
*
: A channel set as a Favorite.
y
)
: A reserved program.
y
(
: A program currently being broadcast.
Memorizing channels
Antenna (Switch to Cable / Switch to Air
t
)
Before your television can begin memorizing the available channels, you
must specify the type of signal source that is connected to the TV (i.e.
an or a system).Air Cable
Auto Program
✎When selecting the Cable TV system: Selects the cable system.
STD HRC IRC, and identify various types of cable TV systems.
Contact your local cable company to identify the type of cable
system that exists in your particular area. At this point, the signal
source has been selected.
✎After all the available channels are stored, it starts to remove
scrambled channels. The menu then reappears.Auto Program
✎Press the ENTER
E
button to stop the channel store during Auto
Program.
How to Stop Auto Programming
1. Press the ENTER
E
button.
2. Stop Auto Program?A message will ask . Select Yes by pressing
the or button.◄ ►
3. Press the ENTER
E
button.
Other Features
Clear Scrambled Channel
This function filters out scrambled channels after is Auto Program
completed. This process may take up to 20~30 minutes.
✎Press the ENTER
E
button to stop the Clear Scrambled
Channel.
✎This function is only available in mode. Cable
Channel List
Channel List Option Menu
OChannel List →
t
Set each channel using the menu options. Option menu Channel List
items may differ depending on the channel status.
■
Add / Delete: Delete or add a channel to display the channels you
want.
✎All deleted channels will be shown on the menu.All Channels
✎A gray-colored channel indicates the channel has been deleted.
✎The menu only appears for deleted channels.Add
✎Delete a channel from the or menu in Added Channels Favorite
the same manner.
■
Add to Favorite / Delete from Favorite
t
: Set channels you
watch frequently as Favorites.
■
Timer Viewing: You can set a desired channel to be displayed
automatically at the set time; even when you are watching another
channel. Set the current time first to use this function.
✎Only memorized channels can be reserved.
✎Reserved programs will be displayed in the menu.Programmed
✎When a digital channel is selected, press the ( ) ►Next Program
button to view the digital program. If you select the ENTER
E
( ) button on the next program, you can set Schedule Timer
Viewing directly.
■
Channel Name Edit: (analog channels only) Assign your own
channel name.
■
Select All: Select all the channels in the channel list.
■
Deselect All: Deselect all the selected channels.
✎You can only select when one or more channels Deselect All
are selected.
■
Auto Program: Scans for a channel automatically and stores in the
TV.
Programmed
(in )Channel List
OChannel List Programmed → →
t
You can view, modify or delete a show you have reserved to watch.
■
Change Info: Change a show you have reserved to watch.
■
Cancel Schedules: Cancel a show you have reserved to watch.
■
Information: Display a show you have reserved to watch. (You can
also change the reservation Information.)
■
Select All / Deselect All: You can select or deselect all channels in
the channel list.
Channel Mode
Change the channel mode directly between and Added Channels
Favorite Channels.
✎The is enabled only when you set Favorite Channels Add to
Favorite.
Fine Tune
(analog channels only)
If the reception is clear, you do not have to fine tune the channel, as
this is done automatically during the search and store operation. If the
signal is weak or distorted, fine tune the channel manually.
✎Fine tuned channels that have been saved are marked with an
asterisk “*” on the right-hand side of the channel number in the
channel banner.
✎To reset the fine-tuning, select .Reset
Picture Menu
Mode
t
Select your preferred picture type.
✎When connecting a PC, you can only select and Entertain
Standard.
■
Dynamic: Suitable for a bright room.
■
Standard: Suitable for a normal environment.
■
Movie: Suitable for watching movies in a dark room.
■
Entertain: Suitable for watching movies and games.
✎Only available when connecting a PC.
Backlight / Contrast / Brightness / Sharpness /
Color / Tint (G/R)
Your television has several setting options for picture quality control.
✎When connecting a PC, you can only make changes to , Backlight
Contrast Brightness Sharpness, and .
Advanced Settings
(available in mode)Standard / Movie
Compared to previous models, new Samsung TVs have a more precise
picture.
✎When connecting a PC, you can only make changes to and Gamma
White Balance.
■
Dynamic Contrast: Adjusts the screen contrast.
■
Black Tone: Selects the black level to adjust the screen depth.
■
Flesh Tone: Emphasize pink “flesh tone”.
■
Color Space: Adjusts the range of colors available to create the
image.
■
White Balance: Adjusts the color temperature for a more natural
picture.
R-Offset / G-Offset / B-Offset: Adjusts each color’s (red, green, blue)
darkness.
R-Gain / G-Gain / B-Gain: Adjusts each color’s (red, green, blue)
brightness.
Reset White Balance: Resets the to it’s default settings.
■
Gamma: Adjusts the primary color intensity.
■
Motion Lighting: Reduce power consumption by brightness control
adapted motion.
✎Available in mode only.Standard
Picture Options
✎When connecting a PC, you can only make changes to the Color
Tone Size HDMI Black Level, , and .
■
Color Tone
✎Warm1 Warm2 or will be deactivated when the picture mode is
Dynamic.
■
Size: Your cable box/satellite receiver may have its own set of screen
sizes as well. However, we highly recommend you use 16:9 mode
most of the time.
16:9: Sets the picture to 16:9 wide mode.
Zoom1: Use for moderate magnification.
Zoom2: Use for a stronger magnification.
Wide Fit: Enlarges the aspect ratio of the picture to fit the entire
screen.
4:3: Sets the picture to basic (4:3) mode.
✎Do not watch in 4:3 format for a long time. Traces of borders
displayed on the left, right and center of the screen may cause
image retention (screen burn) which are not covered by the
warranty.
Screen Fit: (DTV) Displays the full image without any cut-off when
HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals
are inputted.
✎HD (High Definition): 16:9 - 1080i/1080p (1920x1080), 720p
(1280x720)
✎Settings can be adjusted and stored for each external device you
have connected to an input on the TV.
✎Picture Sizes available by Input Source:
Input Source Picture Size
ATV, AV, Component (480i, 480p) 16:9, Zoom1, Zoom2, 4:3
DTV(1080i, 1080p), Component
(1080i, 1080p), HDMI (720p, 1080i,
1080p)
16:9, Wide Fit, 4:3, Screen Fit
■
Digital Clean View: If the broadcast signal received by your TV is
weak, you can activate the feature to reduce any Digital Clean View
static and ghosting that may appear on the screen.
✎When the signal is weak, try other options until the best picture
is displayed.
■
MPEG Noise Filter: Reduces MPEG noise to provide improved
picture quality.
■
HDMI Black Level: Selects the black level on the screen to adjust the
screen depth.
✎Available only in mode (RGB signals).HDMI
■
Film Mode: Sets the TV to automatically sense and process film
signals from all sources and adjusts the picture for optimum quality.
✎Available in ATV, DTV(interlace), AV, COMPONENT (480i / 1080i)
and HDMI (480i / 1080i).
■
LED Clear Motion: Removes drag from fast scenes with a lot of
movement to provide a clear picture.
Picture Reset
Resets your current picture mode to its default settings.
■
Reset Picture Mode: Returns all picture values in the currently
selected mode to the default settings.
Sound Menu
Mode
t
■
Standard: Selects the normal sound mode.
■
Music: Emphasizes music over voices.
■
Movie: Provides the best sound for movies.
■
Clear Voice: Emphasizes voices over other sounds.
■
Amplify: Increase the intensity of high-frequency sounds to allow a
better listening experience for the hearing impaired.
Equalizer
(standard sound mode only)
■
Balance L/R: Adjusts the balance between the right and left speaker.
■
100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment):
Adjusts the level of specific bandwidth frequencies.
■
Reset: Resets the equalizer to its default settings.
DTS TruSurround
(standard sound mode only)
DTS TruSurround is a patented DTS technology that solves the problem
of playing 5.1 multichannel content over two speakers. TruSurround
delivers a compelling, virtual surround sound experience through any
two-speaker playback system, including internal television speakers. It is
fully compatible with all multichannel formats.
Preferred Language
(digital channels only)
Digital-TV broadcasts are capable of simultaneous transmission of many
audio tracks (for example, simultaneous translations of the program into
foreign languages).
✎You can only select a language from among the ones being
broadcasted.
Multi-Track Sound
(analog channels only)
■
Mono: Choose for channels that are broadcasting in mono or if you
are having difficulty receiving a stereo signal.
■
Stereo: Choose for channels that are broadcasting in stereo.
■
SAP: Choose to listen to the Separate Audio Program, which is
usually a foreign-language translation.
✎Depending on the program being broadcast, you can listen to
Mono, Stereo SAP or .
Auto Volume
Because each broadcasting station has its own signal conditions, the
volume may fluctuate each time channel is changed. This feature lets
you automatically adjust the volume of the desired channel by lowering
the sound output when the modulation signal is high or by raising the
sound output when the modulation signal is low.
Visual Impaired
(digital channels only)
Adds verbal description to the main audio to help the visually impaired.
Sound Reset
■
Reset All: Resets all sound settings to the factory defaults.
Setup Menu
Language
Set the menu language.
✎Choose between , , and .English Español Français
Setting the Time
Time
✎The current time will appear every time you press the button.INFO
■
Clock: Setting the clock is for using various timer features of the TV.
✎If you disconnect the power cord, you have to set the clock again.
Clock Mode: Set the current time manually or automatically.
Clock Set Month Day Year Hour Minute am/pm: Set the , , , , and .
✎Available only when is set to .Clock Mode Manual
Time Zone: Select your time zone.
DST: (Daylight Saving Time) Switches the DST (Daylight Saving Time)
function on or off.
✎DST Time Zone Clock and function is only available when the
Mode Auto is set to .
■
Sleep Timer
t
Automatically shuts off the TV after a preset period of time. (30, 60,
90, 120, 150 and 180 minutes).
✎To cancel the , select .Sleep Timer Off
Timer 1 / Timer 2 / Timer 3
Three different on / off timer settings can be made. You must set the
clock first.
■
On Time / Off Time: Set the hour, minute, am/pm and Activate /
Inactivate. (To activate the timer with the setting you have chosen, set
to .)Activate
■
Volume: Set the desired volume level.
■
Contents On Time: When the is activated, you can turn on a specific
channel or play back contents such as photo or audio files.
− TV/USB: Select or . (Make sure that an USB device is TV USB
connected to your TV.)
−Antenna: Displays the current antenna source.
−Channel: Select the desired channel.
− Music/Photo: Select the folder containing MP3/JPEG files on the
USB device.
✎The maximum displayed number of files, including sub folders, in
one folder of USB storage device is 2000.
✎The media may not be playing smoothly when using the device
lower than USB 2.0.
■
Repeat Once Everyday Mon~Fri Mon~Sat Sat~Sun: Select , , , , or
Manual Manual to set at you convenience. If you select , you can set
up the day you want to activate the timer.
Other Features
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™,
you can enjoy a more realistic gaming experience by selecting the game
menu.
✎Precautions and limitations for game mode
xTo disconnect the game console and connect another external
device, set to in the setup menu.Game Mode Off
xIf you display the TV menu in , the screen shakes Game Mode
slightly.
xGame Mode TV is not available when the input source is set to .
xAfter connecting the game console, set to . Game Mode On
Unfortunately, you may notice reduced picture quality.
LED TV
user manual
© 2013 Samsung Electronics Co., Ltd. All rights reserved.
Changing the Input Source
Source List
Use to select TV or an external input source such as a DVD player / Blu-
ray player / cable box / STB satellite receiver.
1. Press the SOURCE button.
2. Select a desired external input source.
■
TV / AV / Component / HDMI
✎You can only choose external devices that are connected to the TV.
In the , connected inputs will be highlighted.Source List
How to use Edit Name
Edit Name lets you associate a device name to an input source. To
access , press the button in . Name the Edit Name TOOLS Source List
device connected to the input jacks to make your input source selection
easier.
✎When connecting a DVD to the port with HDMI HDMI IN (STB)
cable, you should set the TV to mode under .DVD Edit Name
Information
You can see detailed information about the connected external device.
yThe slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of this
apparatus, and to protect it from overheating, these slots and openings must never be blocked or covered.
- Do not cover the slots and openings with a cloth or other materials.
- Do not block the slots and openings by placing this apparatus on a bed, sofa, rug or other similar surface.
- Do not place this apparatus in a confined space, such as a bookcase or built-in cabinet, unless proper ventilation is provided.
yDo not place this apparatus near or over a radiator or heat register, or where it is exposed to direct sunlight.
yDo not place a vessel containing water (vases etc.) on this apparatus, as this can result in a risk of fire or electric shock.
yDo not expose this apparatus to rain or place it near water (near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near
a swimming pool etc.). If this apparatus accidentally gets wet, unplug it and contact an authorized dealer immediately.
yMake sure to pull out the power cord from the outlet before cleaning.
yThis apparatus use batteries. In your community, there might be regulations that require you to dispose of these batteries properly to protect
the environment. Please contact your local authorities for disposal or recycling information.
yDo not overload wall outlets, extension cords, or adaptors beyond their capacity, since this can result in fire or electric shock.
yPower-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay
particular attention to cords at the plug end, where connected to adaptors, and at the point where they exit from the apparatus.
yTo protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power line surges.
yBefore connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor corresponds to the local
electrical supply. (depending on the model)
yNever insert anything metallic into the open parts of this apparatus. Doing so may create a danger of electric shock.
yTo avoid electric shock, never touch the inside of this apparatus. Only a qualified technician should open this apparatus.
yMake sure to plug the power cord in until it is firmly inserted. Pull on the plug, not the cord, when removing the power cord from the outlet. Do
not touch the power cord with wet hands.
yIf this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and
contact an authorized dealer or service center.
yBe sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an extended period of time
(especially when children, elderly or disabled people will be left alone in the house).
- Accumulated dust can cause an electric shock, an electric leakage, or a fire by causing the power cord to generate sparks and heat,
or cause the insulation to deteriorate.
yBe sure to contact an authorized service center, when installing your set in a location with heavy dust, high or low temperatures, high humidity,
chemical substances or where it will operate for 24 hours a day such as in an airport, a train station, etc. Failure to do so may cause serious
damage to your set.
yUse only a properly grounded plug and receptacle.
- An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
yTo turn off the apparatus completely, you must pull the power plug out of the wall socket. Consequently, the power plug should be readily
accessible at all times.
yDo not allow children to hang onto the product.
yStore the accessories (batteries, etc.) in a location safely out of the reach of children.
yDo not install the product in an unstable location such as a shaky self, a slanted floor, or a location exposed to vibration.
yDo not drop or impart a shock to the product. If the product is damaged, disconnect the power cord and contact a service center.
yTo clean the product, unplug the power cord from the power outlet and wipe the product using a soft cloth dipped in a small amount of water.
Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. This may damage the
appearance or erase the printing on the product.
yDo not expose the apparatus to dripping or splashing.
yDo not dispose of batteries in a fire.
yDo not short circuit, disassemble, or overheat the batteries.
yThere is a danger of explosion if you replace the batteries with the wrong type of battery. Replace only with the same or equivalent type.
yWARNING - TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL
TIMES.
Warning! Important Safety Instructions
Please read the safety instructions below before installing and using the product.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). THERE
ARE NO USER SERVICEABLE PARTS INSIDE. REFER
ALL SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
This symbol indicates that high voltage is
present inside. It is dangerous to make any kind
of contact with any internal part of this product.
This symbol indicates that important literature
concerning operation and maintenance has
been included with this product.
HDMI OUT
W R
RW
AUDIO OUT
L-AUDIO-R
AUDIO OUT
L-AUDIO-R
COMPONENT OUT
PRPBY
RB
RBG
G
ANT OUT
VIDEO OUT
Y
Y
W R
RW
or
Power Input
TV Rear Panel
VHF/UHF Antenna
Cable
USB
Component connection
HDMI connection
AV connection
Blu-ray player / DVD / Set-top box
Blu-ray player / DVD
VCR / Blu-ray player
Figures and illustrations in this User Manual are provided for reference only and
may differ from actual product appearance. Product design and specifications
may be changed without notice.
Still image warning
Avoid displaying still images (such as jpeg picture files) or still image elements (such
as TV channel logos, panorama or 4:3 image format, stock or news bars at screen
bottom etc.) on the screen. Constant displaying of still pictures can cause ghosting of
LED screen, which will affect image quality. To reduce risk of this effect, please follow
below recommendations:
yAvoid displaying the same TV channel for long periods.
yAlways try to display any image on full screen, use TV set picture format menu for
best possible match.
yReduce brightness and contrast values to minimum required to achieve desired
picture quality, exceeded values may speed up the burnout process.
yFrequently use all TV features designed to reduce image retention and screen
burnout, refer to proper user manual section for details.
Securing the Installation Space
Keep the required distances between the product and other objects (e.g. walls) to
ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in
the internal temperature of the product.
✎When using a stand or wall-mount, use parts provided by Samsung Electronics
only.
• If you use parts provided by another manufacturer, it may result in a problem
with the product or an injury due to the product falling.
✎The appearance may differ depending on the product.
✎Be careful when you contact the TV because some parts can be somewhat hot.
Installation with a stand. Installation with a wall-mount.
4inches
4inches
4inches
4inches
4inches4inches
4inches
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care center.
Country Customer Care Center Web Site
MEXICO 01-800-SAMSUNG (726-7864) www.samsung.com
Dirección: GENERAL MARIANO ESCOBEDO 476 PISO 8
COL. ANZURES, DELEGACIÓN MIGUEL HIDALGO MÉXICO, DISTRITO
FEDERAL C.P. 11590
ARGENTINE 0800 333 3733 www.samsung.com.ar
URUGUAY 000 405 437 33 www.samsung.com
PARAGUAY 009 800 542 0001 www.samsung.com.py
BRAZIL 0800-124-421 (Demais cidades
e regiões)
4004-0000 (Capitais e grandes
centros)
www.samsung.com.br
CHILE 800-SAMSUNG(726-7864) www.samsung.com/cl
BOLIVIA 800-10-7260 www.samsung.com
COLOMBIA 01 8000 112 112
Bogotá 600 12 72
www.samsung.com/co
COSTA RICA 0-800-507-7267 www.samsung.com/latin (Spanish)
www.samsung.com/latin_en (English)
DOMINICA 1-800-751-2676 www.samsung.com/latin (Spanish)
www.samsung.com/latin_en (English)
ECUADOR 1-800-10-7267 www.samsung.com/latin (Spanish)
www.samsung.com/latin_en (English)
EL SALVADOR 800-6225 www.samsung.com/latin (Spanish)
www.samsung.com/latin_en (English)
GUATEMALA 1-800-299-0013 www.samsung.com/latin (Spanish)
www.samsung.com/latin_en (English)
HONDURAS 800-27919267 www.samsung.com/latin (Spanish)
www.samsung.com/latin_en (English)
JAMAICA 1-800-234-7267 www.samsung.com
NICARAGUA 001-800-5077267 www.samsung.com/latin (Spanish)
www.samsung.com/latin_en (English)
PANAMA 800-7267 www.samsung.com/latin (Spanish)
www.samsung.com/latin_en (English)
PERU 0-800-777-08 www.samsung.com/pe
PUERTO RICO 1-800-682-3180 www.samsung.com
TRINIDAD &
TOBAGO 1-800-SAMSUNG (726-7864) www.samsung.com
VENEZUELA 0-800-100-5303 www.samsung.com/ve
(Sólo Mexico)
IMPORTADO POR : SAMSUNG ELECTRONICS MÉXICO S.A. DE C.V.
GENERAL MARIANO ESCOBEDO 476 PISO 8
COL. ANZURES, DELEGACIÓN MIGUEL HIDALGO MÉXICO, DISTRITO
FEDERAL C.P. 11590
TEL : 01 (55) 5747-5100 / 01 800 726 7864
BN68-05762E-00
yRemote Control & Batteries (AAA x 2)
yWarranty Card / Regulatory Guide
yOwner’s Instructions
yPower Cord
yCable Manager
Display Modes (HDMI Input)
Optimal resolution
4 series:1366 x 768@60Hz / 5 series: 1920 x 1080@60Hz
Mode Resolution
Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync
Polarity
(H / V)
1366 x 768 1920 x 1080
IBM 31,469 70,087 28,322 -/+ 720 x 400
c c
MAC
640 x 480 35,000 66,667 30,240 -/-
c c
832 x 624 49,726 74,551 57,284 -/-
c c
1152 x 870 68,681 75,062 100,000 -/-
c
VESA DMT
640 x 480 31,469 59,940 25,175 -/-
c c
640 x 480 37,861 72,809 31,500 -/-
c c
640 x 480 37,500 75,000 31,500 -/-
c c
800 x 600 37,879 60,317 40,000 +/+
c c
800 x 600 48,077 72,188 50,000 +/+
c c
800 x 600 46,875 75,000 49,500 +/+
c c
1024 x 768 48,363 60,004 65,000 -/-
c c
1024 x 768 56,476 70,069 75,000 -/-
c c
1024 x 768 60,023 75,029 78,750 +/+
c c
1152 x 864 67,500 75,000 108,000 +/+
c
1280 x 720 45,000 60,000 74,250 +/+
c c
1280 x 800 49,702 59,810 83,500 -/+
c
1280 x 1024 63,981 60,020 108,000 +/+
c
1280 x 1024 79,976 75,025 135,000 +/+
c
1366 x 768 47,712 59,790 85,500 +/+
c c
1440 x 900 55,935 59,887 106,500 -/+
c
1600 x 900RB 60,000 60,000 108,000 +/+
c
1680 x 1050 65,290 59,954 146,250 -/+
c
1920 x 1080 67,500 60,000 148,500 +/+
c
Installing batteries (Battery size: AAA)
✎NOTE
• Use the remote control within 23 feet from TV.
• Bright light may affect the performance of the remote control.
Avoid use when nearby fluorescent lights or neon signs.
• The Color and shape may vary depending on the model.
Press to select additional channels (digital) being
broadcasted by the same station. For example, to
select channel ‘54-3’, press ‘54’, then press ‘-’ and ‘3’.
Returns to the previous channel.
Press to directly access to channels.
Turns the TV on and off.
Use these buttons in a specific feature.
P.SIZE: Lets you choose the picture size.
CC: Controls the caption decoder.
: Turns the on or off.Sports Mode
Cuts off the sound temporarily.
Automatically shuts off the TV at a preset time.
Displays the channel list on the screen.
Displays information on the TV screen.
Quickly select frequently used functions.
Selects the on-screen menu items and changes the
values seen on the menu.
Exit the menu.
Returns to the previous menu.
Displays and selects the available video
sources.
Use these buttons according to the direction
on screen.
Changes channels.
Displays the main on-screen menu.
Views the .Media Play
Adjusts the volume.
MEDIA.P SLEEP
FÚTBOL
- 2 -- 1 -
- 6 -- 5 -
- 3 -
- 7 -
- 4 -
- 8 -
BN68-05762E_ENG-US.indd 1 2014-02-03 �� 2:38:10
Application Menu
Using the Media Play
Enjoy photos, music and/or movie files saved on a
USB Mass Storage Class (MSC) device.
MEDIA.P
Connecting a USB Device
1. Turn on your TV.
2. Connect a USB device containing photo, music and/or movie files to
the jack on the rear of the TV.USB
3. When USB is connected to the TV, you can select Media Play (USB)
in menu.Applications
Using the Media Play Menu
1. Press the MENU button. Press the or button to select ▲ ▼
Applications, then press the ENTER
E
button.
2. Media Play (USB)Press the or button to select ▲ ▼ , then press the
ENTER
E
button.
3. Videos, Music, Photos, Press the or button to select an icon (◄ ►
Settings), then press the ENTER
E
button.
✎It might not work properly with unlicensed multimedia files.
✎Need-to-Know List before using Media Play (USB)
xSupported file systems are FAT and NTFS.
xCertain types of USB Digital camera and audio devices may not
be compatible with this TV.
xMedia Play only supports USB Mass Storage Class (MSC)
devices. MSC is a Mass Storage Class Bulk-Only Transport
device. Examples of MSC are Thumb drives and Flash Card
Readers. Devices should be connected directly to the TV’s USB
port. USB HDD is not supported.
xBefore connecting your device to the TV, please back up your files
to prevent them from damage or loss of data. SAMSUNG is not
responsible for any data file damage or data loss.
xA USB device that requires high power (more than 0.5A) may not
be supported.
xDo not disconnect the USB device while it is loading.
xThe higher the resolution of the image, the longer it takes to
display on the screen.
xThe maximum supported JPEG resolution is 15360 x 8640 pixels.
xIf a file is corrupted or the TV does not support the file type, the
“Not Supported File Format” message appears.
xThe TV cannot play MP3 files with DRM that have been
downloaded from a for-pay site. Digital Rights Management
(DRM) is a technology that supports the creation, distribution,
and management of digital content in an integrated and
comprehensive way, including protecting the rights and interests
of content providers, preventing illegal copying of contents, and
managing billings and settlements.
xPTP device is not supported.
xIf an over-power warning message is displayed while you are
connecting or using a USB device, the device may not be
recognized or may malfunction.
xIf the TV has no input during the time set in Auto Protection
Time, the Screensaver will run.
xThe power-saving mode of some external hard disk drives may be
released automatically when your connect them to the TV.
xIf you use a USB extension cable, the TV may not recognize the
USB device or may not be able to read the files on the device.
xIf a USB device connected to the TV is not recognized, the list of
files on the device is corrupted, or a file in the list is not played,
connect the USB device to a PC, format the device, and check
the connection.
xIf a file you deleted from the PC is still found when you run Media
Play, use the “Empty the Recycle Bin” function on the PC to
permanently delete the file.
xPhotos only supports sequential jpeg format.
xThe scene search and thumbnail functions are not supported in
the . Videos
xIf the number of files and folders saved on a USB storage device is
approximately over 4000, the files and folders may not appear and
some folders may not be opened.
xThe maximum displayed number of files, including sub folders, in
one folder of USB storage device is 2000.
xThe media may not be playing smoothly when using the device
lower than USB 2.0.
Videos
1. VideosPress the buttons to select ◄/► , then press the ENTER
E
button in the menu.Media Play
2. Press the buttons to select the desired video in the file ◄/►/▲/▼
list.
3. Press the ENTER
E
button or
�
(Play) button.
- The selected file is displayed on the top with its playing time.
- If video time information is unknown, playing time and the progress
bar are not displayed.
- During video playback, you can search using the buttons.◄/►
✎In this mode, you can play movie clips contained in a game, but you
cannot play the game itself.
ySupported Subtitle Formats
- External
Name File extension
MPEG-4 timed text .ttxt
SAMI .smi
SubRip .srt
SubViewer .sub
Micro DVD .sub or .txt
SubStation Alpha .ssa
Advanced SubStation Alpha .ass
- Internal
Name Container Format
Xsub Picture FormatAVI
SubStation Alpha MKV Text Format
Advanced SubStation Alpha MKV Text Format
SubRip MKV Text Format
MPEG-4 Timed text MP4 Text Format
ySupported Video Formats
File
Extension Container Video Codec Resolution Frame
rate (fps)
Bit rate
(Mbps)
Audio
Codec
*.mp4 MP4
Divx3.11/4.x/
5.1/6.0 1920x1080 6~30 30Mbps
MP3 /
ADPCM /
AAC
H264 1920x1080 6~30 30Mbps
AVC 1920x1080 6~30 30Mbps
MJPEG 640x480 6~30 10Mbps
"*.avi
*.mkv"
"AVI
MKV"
Divx3.11/4.x/
5.1/6.0 1920x1080 6~30 30Mbps "MP3 /
AC3 /
LPCM /
ADPCM
/ DTS
Core"
MPEG4 SP/
ASP 1920x1080 6~30 30Mbps
H264 1920x1080 6~30 30Mbps
MJPEG 640x480 6~30 10Mbps
"*.asf
*.wmv" ASF
Divx
3.11/4.x/
5.1/6.0
1920x1080 6~30 30Mbps
"MP3 /
AC3 /
LPCM /
ADPCM
/ WMA
/ WMA
Pro"
MPEG4 SP/
ASP 1920x1080 6~30 30Mbps
H.264 1920x1080 6~30 30Mbps
"*.ts
*.trp
*.tp
*.m2ts"
TS
MPEG2 1920x1080 6~30 30Mbps AC3 /
AAC /
MP3 /
DD+ /
HE-AAC
H. 264 BP/
MP/HP 1920x1080 6~30 30Mbps
The picture is black and white. If you are using an AV composite input, connect the video cable (yellow) to the Green jack of component input 1 on the TV.
When changing channels, the picture
freezes or is distorted or delayed.
yIf connected to a cable box, please try to reset it. (Reconnect the AC cord and wait until the cable box reboots. It may take
up to 20 minutes)
ySet the output resolution of the cable box to 1080i or 720p.
Sound Problem Sound TestFirst of all, please perform the to confirm that your TV audio is properly operating.
(Go to - MENU Support - Self Diagnosis - Sound Test)
If the audio is OK, the sound problem may caused by the source or signal.
There is no sound or the sound is too low at
maximum volume.
Please check the volume of the device (Cable/Sat Box, DVD, Blu-ray, etc.) connected to your TV.
The picture is good but there is no sound. yIf you are using an external device, check the device’s audio output option (ex. you may need to change your cable box’s
audio option to HDMI when you have a HDMI connected to your TV).
yReboot the connected device by reconnecting the device’s power cable.
The speakers are making an inappropriate
noise.
yCheck the cable connections. Make sure a video cable is not connected to an audio input.
yFor Antenna or Cable connections, check the signal information. A weak signal may cause sound distortion.
yPerform the Sound Test as explained above.
No Picture, No Video
The TV will not turn on. yMake sure the AC power cord is securely plugged into the wall outlet and the TV.
yMake sure the wall outlet is working.
yTry pressing the button on the TV to make sure the problem is not the remote. POWER
If the TV turns on, refer to ‘Remote control does not work’ below.
The TV turns off automatically. yEnsure the is set to in the menu.Sleep Timer Off Time
yIf your PC is connected to the TV, check your PC power settings.
yMake sure the AC power cord is plugged in securely to the wall outlet and the TV.
yWhen you are watching TV connected to an antenna or cable connection, the TV will turn off after 10 - 15 minutes if there
is no signal.
There is no picture/video. yCheck the cable connections. (Remove and reconnect all cables connected to the TV and external devices).
ySet your external device’s (Cable/Sat Box, DVD, Blu-ray etc) video outputs to match the connections to the TV input. For
example, if an external device’s output is HDMI, it should be connected to an HDMI input on the TV.
yMake sure your connected devices are powered on.
yBe sure to select the TV’s correct source by pressing the button on the remote control.SOURCE
yReboot the connected device by reconnecting the device’s power cable.
RF(Cable/Antenna) Connection
The TV is not receiving all channels. yMake sure the coaxial cable is connected securely.
yPlease try Auto Program to add available channels to the channel list.
go to - - then select and make sure the correct Cable TV signal type is set in the MENU Channel Auto Program Auto
menu. There are 3 options. ( , and )STD HRC IRC
yVerify the antenna is positioned correctly.
No Caption on digital channels. yCheck the Caption Setup menu. Try changing to .Caption Mode Service1 CC1
ySome channels may not have caption data.
The picture is distorted: macroblock, error,
small block, dots, pixelization.
yCompression of video contents may cause picture distortion. Especially on fast moving pictures such as sports and action
movies.
yA weak signal can cause picture distortion. This is not a TV problem.
Others
Purple/green rolling horizontal bars and
buzzing noise from the TV speakers with
Component cable connection.
Remove the left and right audio connections from the set-top-box. If the buzzing stops, this indicates that the set-top-box has
a grounding issue. Replace the Component video cables with an HDMI connection.
The picture will not display in full screen. yHD channels will have black bars on either side of the screen when displaying up scaled SD (4:3) contents.
yBlack bars on the Top & Bottom will be shown on movies that have aspect ratios different from your TV.
yAdjust the picture size option on your external device or change the TV to full screen.
The remote control does not work. yReplace the remote control batteries with correct polarity (+/–).
yClean the transmission window located on the top of the remote control.
yTry pointing the remote directly at the TV from 5~6 feet away.
The cable/set top box remote control
does not turn the TV on or off, or adjust
the volume.
Program the Cable/Set top box remote control to operate the TV. Refer to the Cable/Set top box user manual for the
SAMSUNG TV code.
A “ ” message Mode Not Supported
appears.
Check the supported resolution of the TV and adjust the external device’s output resolution accordingly. Refer to resolution
settings in this manual.
Caption on the TV menu is greyed out. yYou cannot select in the TV menu when watching content from a device connected via HDMI or Component.Caption
yCaption must be activated on the external device.
There is a plastic smell from the TV. This smell is normal and will dissipate over time.
File
Extension Container Video Codec Resolution Frame
rate (fps)
Bit rate
(Mbps)
Audio
Codec
"*.dat
*.mpg
*.mpeg
*.vob"
PS
MPEG1 1920x1080 24/25/30 30Mbps AC3 /
MPEG /
LPCM /
AAC
MPEG2 1920x1080 24/25/30 30Mbps
H. 264 BP/
MP/HP 1920x1080 6~30 30Mbps
*.3gp 3GPP
MPEG4 SP/
ASP 1920x1080 6~30 30Mbps MP3
H.264 1920x1080 6~30 30Mbps
*.flv flash
formats
H.264 1920x1080 6~30 30Mbps
MP3
Sorenson
H.263 1920x1080 6~30 30Mbps
Other Restrictions
xVideo content will not play, or not play correctly, if there is an error in
the content or the container.
xSound or video may not work if the contents have a standard bit rate/
frame rate above the compatible Frame/sec listed in the table above.
xIf the Index Table is in error, the Seek (Jump) function is not supported.
xThe menu may take longer to appear if the video’s bit rate exceeds
10Mbps.
xVideo content can not be played, if there are many contents in one file.
Video Decoder Audio Decoder
Supports up to H.264, Level 4.1
H.264 FMO / ASO / RS, VC1 SP / MP /
AP L4 and AVCHD are not supported.
MPEG4 SP, ASP :
– Below 1280 x 720: 60 frame max
– Above 1280 x 720: 30 frame max
H.263 is not supported.
GMC is not support.
Supports up to WMA7, 8, 9
STD, 9 PRO, and 10 PRO
WMA 9 PRO and WMA 10 PRO
support 5.1 channel.
(LBR mode of WMA Pro is not
supported.)
WMA Lossless is not supported.
Music
1. MusicPress the buttons to select ◄/► , then press the ENTER
E
button in the menu.Media Play
2. Press the buttons to select the desired Music in the file ◄/►/▲/▼
list.
3. Press the ENTER
E
button or (Play) button.
✎During music playback, you can search using the buttons.◄/►
✎ (REW) and (FF) buttons do not function during play.
✎Only displays the files with MP3 file extensions. Other file extensions
are not displayed, even if they are saved on the same USB device.
✎If the sound is abnormal when playing MP3 files, adjust the
Equalizer Sound in the menu. (An over-modulated MP3 file may
cause a sound problem.)
Photos
1. PhotosPress the buttons to select ◄/► , then press the ENTER
E
button in the menu.Media Play
2. Press the buttons to select the desired photo in the file ◄/►/▲/▼
list.
3. Press the ENTER
E
button or (Play) button.
✎NOTE
- While a photo list is displayed, press the (Play) / ENTER
E
button on the remote control to start the slide show.
- All files in the file list section will be displayed in the slide show.
- During the slide show, files are displayed in order.
- During the slide show, you can adjust the slide show speed using
(REW) or (FF) button.
- You can move to other file using the buttons.◄/►
ySupported Photo Formats
Image Photo Resolution
JPEG Base-line 15360 x 8704
Progressive 1024 x 768
Other Restrictions
CMYK and YCCK Color space JPEGs are not supported.
Playing Multiple Files
■
Playing selected video/music/photo files
1. Press the Yellow button in the file list to select the desired file.
2. Repeat the above operation to select multiple files.
✎NOTE
- The
c
mark appears to the left of the selected files.
- To cancel a selection, press the Yellow button again.
- To deselect all selected files, press the button and select TOOLS
Deselect All.
3. Play Selected ContentsPress the TOOLS button, and then select .
■
Playing the video/music/photo file group
1. While a file list is displayed, move to any file in desired group.
2. Play FolderPress the TOOLS button, and then select .
Media Play - Additional Functions
■
Videos/Music/Photos Play Option menus
When playing a file, press the button.TOOLS
Category Operation Videos Music Photos
Title You can move the other file
directly.
c
Repeat Mode You can play movie and music files
repeatedly.
c c
Picture Size You can adjust the picture size to
your preference.
c
Picture Mode You can adjust the picture setting.
c c
Sound Mode You can adjust the sound setting.
ccc
Subtitle Settings
You can play the video with
Subtitles. This function only works
if the subtitles are the same file
name as the video.
c
Audio Format You can select the digital audio
output format.
c
Audio Language
You can change the audio
language if the video has more
than one language.
c
Stop Slide
Show /
Start Slide Show
You can start or stop a Slide Show.
c
Slide Show
Speed
You can select the slide show
speed during the slide show.
c
Background
Music
You can set and select
background music when watching
a Slide Show.
c
Zoom You can zoom into images in full
screen mode.
c
Rotate You can rotate images in full
screen mode.
c
Information You can see detailed information
about the played file.
ccc
Settings
Using the Setup Menu
■
DivX® Video On Demand: Shows the registration code authorized
for the TV. If you connect to the DivX web site and register with
10-digit registration code, you can download the VOD activation file.
Once you play it using Media Play, the registration is completed.
✎For more information on DivX® VOD, visit “http://vod.divx.com”.
■
Information: Select to view information on the connected device.
Using the Sports Mode
Sports Mode
This mode provides optimised condition for watching sports games.
✎When the is , the picture and sound modes are set Sports Mode On
to automatically.Stadium
Other Information
Installing the Wall Mount Kit
The wall mount kit (sold separately) allows you to mount the TV on the
wall.
For detailed information on installing the wall mount, see the instructions
provided with the wall mount items. Contact a technician for assistance
when installing the wall mount bracket. Samsung Electronics is not
responsible for any damage to the product or injury to yourself or others
if you elect to install the wall mount on your own.
Wall Mount Kit Specifications (VESA)
✎The wall mount kit is not supplied, but sold separately.
Install your wall mount on a solid wall perpendicular to the floor. When
attaching to other building materials, please contact your nearest dealer.
If you install the TV on a ceiling or slanted wall, it may fall and result in
severe personal injury.
✎NOTE
xStandard dimensions for wall mount kits are shown in the table
below.
xWhen purchasing our wall mount kit, a detailed installation manual
and all parts necessary for assembly are provided.
xDo not use screws that do not comply with the VESA standard
screw specifications.
xDo not use screws that are longer than the standard dimension
or do not comply with the VESA standard screw specifications.
Screws that are too long may cause damage to the inside of the
TV set.
xFor wall mounts that do not comply with the VESA standard screw
specifications, the length of the screws may differ depending on
the wall mount specifications.
xDo not fasten the screws too firmly. This may damage the product
or cause the product to fall, leading to personal injury. Samsung is
not liable for these kinds of accidents.
xSamsung is not liable for product damage or personal injury when
a non-VESA or non-specified wall mount is used or the consumer
fails to follow the product installation instructions.
xDo not mount the TV at more than a 15 degree tilt.
xAlways have two people mount the TV on a wall.
Product
Family
TV size in
inches
VESA screw hole specs (A
* B) in millimeters
Standard
Screw Quantity
LED-TV
19~22 75 X 75 M4
4
26-28 100 X 100
32-42 200 X 200 M8
46~60 400 X 400
Do not install your Wall Mount Kit
while your TV is turned on. It may
result in personal injury due to
electric shock.
Securing the TV to the Wall
Caution: Pulling, pushing, or climbing onto the TV may
cause the TV to fall. In particular, ensure that your children
do not hang over or destabilize the TV; doing so may cause
the TV to tip over, resulting in serious injuries or death.
Follow all safety precautions provided on the included
Safety Flyer. For added stability, install the anti-fall device for
safety purposes, as follows.
To prevent the TV from falling
✎Since the necessary clamps, screws, and string are not supplied,
please purchase these additionally.
1. Drive the screws into the clamps and firmly fasten them onto the wall.
Make sure the screws are firmly fixed into the wall.
2. Remove the screws from the back center of the TV, put the screws
into the clamps, and then fasten the screws onto the TV again.
3. Connect the clamps fixed onto the TV and the clamps fixed onto the
wall with a strong cable and then tie the string tightly.
✎Verify all connections are properly secured. Periodically check the
connections for any sign of fatigue or failure. If you have any doubt
about the security of your connections, contact a professional
installer.
✎Install the TV close to the wall so that it does not fall.
✎It is safe to connect the string so that the clamps fixed on the wall
are equal to or lower than the clamps fixed on the TV. Untie the
string before moving the TV.
Kensington Lock
The Kensington Lock is not supplied by Samsung. It is a device used
to physically fix the system when using it in a public place. Refer to the
manual provided with the Kensington Lock for additional information on
proper use.
✎Please find a “
K
” icon on the rear of the TV. The Kensington slot is
beside the “
K
” icon.
✎The position and color may differ depending on the model.
Assembling the Cable manager
Program Rating Lock
The feature automatically locks out programs Program Rating Lock
that are deemed inappropriate for children. The user must enter a PIN
(personal identification number) before any of the Program Rating Lock
restrictions are set up or changed.
✎Program Rating Lock HDMI Component is not available in or
mode.
✎The default PIN number of a new TV set is “0-0-0-0”.
■
Program Rating Lock: You can block rated TV Programs.
■
TV Parental Guidelines: You can block TV programs depending on
their rating. This function allows you to control what your children are
watching.
■
MPAA Rating: You can block movies depending on their MPAA
rating. The Motion Picture Association of America (MPAA) has
implemented a rating system that provides parents or guardians with
advanced information on which films are appropriate for children.
■
Canadian English: You can block TV programs depending on their
Anglophone Canadian.
■
Canadian French: You can block TV programs depending on their
French Canadian rating.
■
Downloadable U.S. Rating: Parental restriction information can be
used while watching DTV channels.
■
Change PIN: The Change PIN screen will appear. Choose any 4 digits
for your PIN and enter it in . Re-enter the same 4 digits Enter New PIN
in . When the Change PIN screen disappears, press Confirm New PIN
the OK button. The TV has memorized your new PIN.
✎If you forget the PIN, press the remote-control buttons in the
following sequence, which resets the pin to “0-0-0-0” : POWER
(off) 8 2 4 (on)→MUTE →→→→POWER
Caption
(On-Screen Text Messages)
■
Caption: You can switch the caption function on or off. If captions are
not available, they will not be displayed on the screen.
✎The feature does not work in or Caption Component HDMI
mode.
■
Caption Mode: You can select the desired caption mode.
Default / CC1~CC4 / Text1~Text4: (analog channels only) The
Analog Caption function operates in either analog TV channel mode
or when a signal is supplied from an external device to the TV.
(Depending on the broadcasting signal, the Analog Caption function
may or may not work with digital channels.)
Default / Service1~Service6 / CC1~CC4 / Text1~Text4: (digital
channels only) The Digital Captions function works with digital
channels.
✎Service1~6 may not be available in digital caption mode
depending on the broadcast.
■
Digital Caption Options: (digital channels only)
Size: Options include Default, Small, Standard and Large. The default
is Standard.
Font Style: Options include Default and Styles 0 to 7. The default is
Style 0.
Foreground Color: Options include Default, White, Black, Red,
Green, Blue, Yellow, Magenta and Cyan.
You can change the color of the letter. The default is White.
Background Color: Options include Default, White, Black, Red,
Green, Blue, Yellow, Magenta and Cyan. You can change the
background color of the caption. The default is Black.
Foreground Opacity: This adjusts the opacity of text. Options include
Default, Transparent, Translucent, Solid and Flashing.
Background Opacity: This adjusts the opacity of the caption
background. Options include Default, Transparent, Translucent, Solid
and Flashing.
Return to Default: This option sets each Size, Font Style, Foreground
Color, Background Color, Foreground Opacity and Background
Opacity to its default.
✎Digital Caption Options Default are available only when and
Service1~Service6 Caption Mode can be selected in .
✎The Foreground and Background cannot be set to have the same
color.
Melody
Set so that a melody plays when the TV is turned on or off.
✎The does not play.Melody
xWhen no sound is output from the TV because the button MUTE
has been pressed.
xWhen no sound is output from the TV because the volume has
been reduced to minimum with the button.VOL –
xWhen the TV is turned off by function.Sleep Timer
Eco Solution
■
Energy Saving: This adjust the brightness of the TV in order to
reduce power consumption. If you select Picture Off, the screen is
turned off, but the sound remains on. Press any button except volume
button to turn on the screen.
■
No Signal Power Off : Sets how quickly the TV switches to standby
mode, if no picture is being received.
✎Disabled when the PC is in power saving mode.
■
Auto Power Off: The TV will be automatically turned off when no user
operation is received for 4 hours.
Auto Protection Time
If the screen remains idle with a still image for a certain period of
time defined by the user, the screen saver is activated to prevent the
formation of ghost images on the screen.
Support Menu
Self Diagnosis
■
Picture Test: Use to check for picture problems. If the problem
continues to occur, check the color pattern.
■
Sound Test: Use the built-in melody sound to check for sound
problems.
■
Signal Strength: (digital channels only) An HD channel’s reception
quality is either perfect or the channels are unavailable. Adjust your
antenna to increase signal strength.
■
Reset: Reset all settings to the factory defaults.
✎The PIN input screen appears before the setup screen.
✎Enter your 4-digit PIN. Change the PIN using the Change PIN
option.
Software Upgrade
Software Upgrade can be performed by downloading the latest
firmware from samsung.com to a USB memory device.
HD Connection Guide
Refer to this information when connecting external devices to the TV.
Contact Samsung
View this information when your TV does not work properly or when you
want to upgrade the software. You can find information regarding our call
centers and how to download products and software.
Troubleshooting
If the TV seems to have a problem, first review this list of possible problems and solutions. If none of these troubleshooting tips apply, visit samsung.
com, then click on Support, or call Samsung customer service.
Problem Possible Solution
Flickering and Dimming If your Samsung Television is flickering or dimming sporadically, you may need to disable some of its energy efficient features
like the or the feature. If you follow below step with your remote, you can turn these features Eco Sensor Energy Saving
off or on.
yEnergy Saving Setup Eco Solution Energy Saving : MENU → → →
Component Connections /
Screen Color
If you find that the color on your Samsung television’s screen is not correct or black and White, first run a on Self Diagnosis
the TV to make sure there are no device issues.
ySelf Diagnosis Support Self Diagnosis Picture Test : MENU → → →
If the test is ok, try making sure:
yYour connections are all consistent. For example, if you’ve used the AV In jack on your TV, make sure you have used the
AV Out jack on your video source.
yTry making sure you have connected to the correct jacks. For example, if you use the Component jacks, labeled Pb, Pr,
and Y, to connect your TV and video source, make sure you have connected the blue Pb jack on the video source to the
blue Pb jack on the TV, the red Pr jack on the source to the red Pr jack on the TV.
Screen Brightness If you find that the colors on your Samsung TV are correct but just a little too dark or bright, there are some settings you
should check before calling for a repair.
yBacklight Contrast Brightness Sharpness Color Tint (G/R) Picture, , , , , and so on. Go in to “ ” on user Menu then try
adjusting options mentioned above.
Unwanted Powering off If your Samsung TV appears to turn off by itself, there may be an issue with either your Timer settings or your Eco friendly No
Signal Power Off feature.
First make sure you is not accidentally set. The sleep timer allows you the comfort of falling asleep with the TV Sleep Timer
still on but, turns it off after a certain period of time so as not to waste energy.
ySleep Timer Setup Time Sleep Timer : MENU → → →
If the Sleep Timer is not activated, you may have engaged the or feature.No Signal Power Off Auto Power Off
yNo Signal Power Off Setup Eco Solution No Signal Power Off : MENU → → →
yAuto Power Off Setup Eco Solution Auto Power Off : MENU → → →
Trouble Powering On Before Turn on check red light on the right or left bottom of your TV. Press power on button on TV or remote and it
will blink about 5 times before turning on.
If you find that you are having trouble powering on your Samsung television, there are a number of things to check before
making a call to the service department.
yIf you happen to be using the TV as a monitor and the stand-by light only blinks for a few seconds when you press the
power button, your PC is in sleep mode. To take your PC out of sleep mode, press a key on your keyboard or move the
mouse. Then try turning your TV on.
If you’re sure your power cord, remote control, and PC are functioning properly, you may be having a cable issue. If you have
a cable or satellite box, your TV may appear to be off because the cable or satellite box is not outputting a signal. To test the
signal output of your cable or satellite box, press the guide or info button on the cable or satellite box remote control. If the
screen displays the guide or info data, the problem is caused by the box.
Stand Assembly If you have any trouble to assemble the stand though you refer to “Install the Stand” mentioned at separate guide.
Cannot find channel Re-run plug and play.
Poor picture Picture TestFirst, perform the and to see if your TV is properly displaying the test image.
Go to - - - MENU Support Self Diagnosis Picture Test
If the test image is properly displayed, the poor picture may be caused by the source or signal.
The TV image does not look as good as it
did in the store.
If you have an analog cable/satellite box, upgrade to a digital set top box. Use HDMI or Component cables to deliver HD (high
definition) picture quality.
Cable/Satellite subscribers: Try HD channels from the channel line up.
Air/Cable Antenna connection: Try HD channels after performing Auto program.
✎Many HD channels are up scaled from SD(Standard Definition) contents.
yAdjust the Cable/Set top box video output resolution to 1080i or 720p.
The picture is distorted: macroblock error,
small block, dots, pixelization.
yCompression of video contents may cause picture distortion, especially on fast moving pictures such as sports and action
movies.
yA weak signal can cause picture distortion. This is not a TV problem.
yMobile phones used close to the TV (within 3.3ft) may cause noise in the picture on analog and digital channels.
Color is wrong or missing. If you’re using a component connection, make sure the component cables are connected to the correct jacks. Incorrect or
loose connections may cause color problems or a blank screen.
There is poor color or brightness. yAdjust the Picture options in the TV menu. (Go to )Picture Mode / Color / Brightness / Sharpness
yAdjust the option in the TV menu. (Go to - - - )Energy Saving MENU Setup Eco Solution Energy Saving
yTry resetting the picture to view the default picture setting. (Go to - )MENU Picture - Picture Reset
There is a dotted line on the edge of the
screen.
yIf the picture size is set to , change it to 16:9.Screen Fit
yChange the cable/satellite box resolution.
TV is unavailable in the Signal Strength
Self Diagnosis Test menu.
This function is only available for digital channels from an Antenna / RF / Coax connection.
TV is tilted to the right or left side. Remove the stand base from the TV and reassemble it.
The menu is greyed out Channel
(unavailable).
The menu is only available when you select the TV source. Channel
Your settings are lost after 30 minutes or
every time the TV is turned off.
If TV is in the mode, it will reset audio and picture settings every 30 minutes. Please change from Store Demo Store Demo
mode to mode using the procedure. Press the button to select TV mode, go to Home Use Plug & Play SOURCE MENU →
Setup Plug & Play → →ENTER
E
.
You have intermittent loss of audio or video. Check the cable connections and reconnect them.
Loss of audio or video can be caused by using overly rigid or thick cables. Make sure the cables are flexible enough for long
term use. If mounting the TV to the wall, we recommend using cables with 90 degree connectors.
You see small particles when you look
closely at the edge of the frame of the TV.
This is part of the product’s design and is not a defect.
POP (TV’s internal banner ad) appears on
the screen.
Select under mode. For details, refer to (Initial Setup).Home Use Plug & Play Plug & Play
✎This TFT LED panel uses a panel consisting of sub pixels which require sophisticated technology to produce. However, there may be a few bright or
dark pixels on the screen. These pixels will have no impact on the performance of the product.
✎Some functions and pictures shown in this manual are available on specific models only.
✎You can keep your TV as optimum condition to upgrade the latest firmware on web site (samsung.com Support Downloads) by USB.→ →
Storage and Maintenance
✎If you attached some stickers on the TV screen, it remains some debris after removing the sticker. Please clean it to watch TV.
✎The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior and screen carefully using a soft cloth to
prevent scratches.
Do not spray water directly onto the
product. Any liquid that goes into the
product may cause a failure, fire, or electric
shock.
Clean the product with a soft cloth
dampened with in a small amount of water.
Do not use a flammable liquid (e.g. benzene,
thinners) or a cleaning agent.
License
DivX Certified® to play DivX® video up to HD 1080p,
including premium content.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX
video. Visit divx. com for more information and software tools to convert your files into
DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be
registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain
your registration code, locate the DivX VOD section in your device setup menu. Go
to vod. divx.com for more information on how to complete your registration. Covered
by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710;
7,519,274 DivX®, DivX Certified® and associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used under license.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under a license from U.S. Patent No’s:
5,956,674, 5,974,380, 5,978,762, 6,487,535, 6,226,616,
7,212,872, 7,003,467, 7,272,567, 7,668,723, 7,392,195,
7,930,184, 7,333,929 and 7,548,853. DTS, the Symbol,
and DTS and the Symbol together are registered
trademarks & DTS Premium Sound is a trademark of
DTS, Inc.
©2012 DTS, Inc. All Rights Reserved.
Manufactured under a license from U.S. Patent No’s:
6,285,767, 8,027,477, 5,319,713, 5,333,201, 5,638,452,
5,771,295, 5,970,152, 5,912,976, 7,200,236, 7,492,907,
8,050,434, 7,720,240, 7,031,474, 7,907,736 and
7,764,802. DTS, the Symbol, and DTS and the Symbol
together are registered trademarks & DTS Studio Sound is
a trademark of DTS, Inc.
©2012 DTS, Inc. All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and
other countries.
Open Source License Notice
Open Source used in this product can be found on the following webpage. (http://
opensource.samsung.com) Open Source License Notice is written only English.
To send inquiries and requests for questions regarding open sources, contact
Samsung via Email (oss.request@samsung.com).
This product uses some software programs which are distributed under the
Independent JPEG Group.
ICU License - ICU 1.8.1 and later
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1995-2008 International Business Machines Corporation and others All
rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge,
publish, distribute, and/or sell copies of the Software, and to permit persons to whom
the Software is furnished to do so, provided that the above copyright notice(s) and
this permission notice appear in all copies of the Software and that both the above
copyright notice(s) and this permission notice appear in supporting documentation.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE
COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE
FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES,
OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used
in advertising or otherwise to promote the sale, use or other dealings in this Software
without prior written authorization of the copyright holder.
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
Specifications
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
50°F to 104°F (10°C to 40°C)
10% to 80%, non-condensing
-4°F to 113°F (-20°C to 45°C )
5% to 95%, non-condensing
Model Name UN32FH4005 UN39FH5005
Display Resolution 1366 x 768 1920 x 1080
Screen Size
(Diagonal)
32" Class
(31,5" measured diagonally)
39" Class
(38,5" measured diagonally)
Sound
Output 5W x 2 10W x 2
Dimensions (W x H x D)
Body
With stand
29,0 X 17,4 X 3,6 inches
(738,4 X 444,0 X 93,2 (mm))
29,0 X 19,5 X 7,5 inches
(738,4 X 497,7 X 191,7 (mm))
35,2 X 20,9 X 3,6 inches
(895,9 X 532,5 X 93,2 (mm))
35,2 X 23,2 X 8,9 inches
(895,9 X 589,3 X 227,6 (mm))
Weight
Without Stand
With Stand
11,9 lbs (5,4 kg)
13,2 lbs (6,0 kg)
17,1 lbs (7,8 kg)
21,6 lbs (9,8 kg)
✎Design and specifications are subject to change without prior notice.
✎This device is a Class B digital apparatus.
✎For information about your TV's power requirements and more about power consumption, refer to the label attached to the product.
✎Typical power consumption is measured according to Energy Star Program requirements for televisions.
- 10 -- 9 -
- 14-- 13 -
- 11 -
- 15 -
- 12 -
- 16 -
BN68-05762E_ENG-US.indd 2 2014-02-03 �� 2:38:12

Especificaciones del producto

Marca: Samsung
Categoría: No categorizado
Modelo: UN32FH4005H

¿Necesitas ayuda?

Si necesitas ayuda con Samsung UN32FH4005H haz una pregunta a continuación y otros usuarios te responderán


No categorizado Samsung Manuales

Samsung

Samsung RS78CG8543B1 Manual de Usario

27 Octubre 2024
Samsung

Samsung SRS694NLS Manual de Usario

27 Octubre 2024
Samsung

Samsung RR22M287YU3 Manual de Usario

25 Octubre 2024
Samsung

Samsung MM-DT10 Manual de Usario

23 Octubre 2024
Samsung

Samsung HG32AJ570NK Manual de Usario

13 Octubre 2024
Samsung

Samsung RH77J90407H Manual de Usario

8 Octubre 2024
Samsung

Samsung CS-21M20ML Manual de Usario

7 Octubre 2024
Samsung

Samsung QB43B Manual de Usario

7 Octubre 2024
Samsung

Samsung CS-21A11MH Manual de Usario

4 Octubre 2024
Samsung

Samsung MR-EH01 Manual de Usario

3 Octubre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024