Shimano CT-S500 Manual de Usario

Shimano Accesorio para bicicleta CT-S500

Lee a continuación 📖 el manual en español para Shimano CT-S500 (1 páginas) en la categoría Accesorio para bicicleta. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/1
Technical Service Instructions
CT-S500
SI-50D0A-001
Chain Tensioner
General Safety Information
Clean the chain tensioner periodically and lubricate all moving parts and
pulleys.
If there is a large amount of play in the pulleys and an abnormal amount of
noise is generated while riding, replace the pulleys.
Parts are not guaranteed against natural wear or deterioration resulting from
normal use.
For any questions regarding methods of handling or maintenance, please
contact the place of purchase.
NOTE:
Chain Chain tool
Reinforced
connecting pin
9-speed super narrow
chain such as
CN-7701/ CN-HG93
8- /7-/ 6-speed narrow
chain such as
CN-HG50/ CN-IG51
Silver
6.5 mm
Black
7.1 mm
TL-CN31/ TL-CN22
TL-CN31/ TL-CN22
and
TL-CN30/ TL-CN21
End pin Link pin Reinforced connecting pin Guide pulley
Sprocket
Spacer
Fixing bolt
Sprocket
Guide pulley
Tension pulley
Perpendicular to ground
Smaller chainring
CT-S500 chain tensioner
Use neutral detergent to clean the chain. Do not use alkali-based or acid-
based detergents such as rust cleaners, as they may result in damage
and/or failure of the chain.
Use the reinforced connecting pin only for connecting the narrow type of
chain.
There are two different types of reinforced connecting pins available. Be
sure to check the table below before selecting which pin to use.
if connecting pins other than reinforced connecting pins are used, or if a
reinforced connecting pin or tool which is not suitable for that type of
chain is used, sufficient connection force may not be obtained, which
could cause the chain to break or fall off.
If it is necessary to adjust the length of the chain due to a change in the
number of sprocket teeth, make the cut at some other place than the
place where the chain has been joined using a reinforced connecting pin
or an end pin.
The chain will be damaged if it is cut at a place where it has been joined
with a reinforced connecting pin or an end pin.
Check that the tension of the chain is correct and that the chain is not
damaged.
If the tension is too weak or the chain is damaged, the chain should be
replaced. If this is not done, the chain may break and cause serious
injury.
Obtain and read the service instructions carefully prior to installing
the parts. Loose, worn, or damaged parts may cause serious injury to
the rider. We strongly recommend only using genuine Shimano
replacement parts.
Read these Technical Service Instructions carefully, and keep them in a
safe place for later reference.
WARNING – To avoid serious injuries:
Be sure to read these service instructions in conjunction with the service
instructions for the hub for Inter-8 disc brake before use.
Installation of the chain tensioner to the frame
Insert a spacer in between the dropout and the chain tensioner so that the guide pulley
of the chain tensioner is directly below the sprocket, and then tighten the fixing bolt.
One spacer with a thickness of 1 mm and two spacers with a thickness of 2 mm are
included.
The total thickness of spacers used should not exceed 5 mm.
Chain length
If the different between the number of teeth on the chainrings is 12T or less, or if the
front chainwheel has a single chainring, set the chain onto the smaller chainring, and
then set the chain tensioner so that the tension pulley and guide pulley are
perpendicular to the ground.
Specifications
Front chainwheel tooth difference
Largest sprocket
Smallest sprocket
Applicable dropout width
16T
20T
18T
5 – 9 mm
Tightening torque:
8 – 10 N·m {80 – 100 kgf·cm}
If the difference in the number of chainring teeth is 13T – 16T, make the chain
one link longer than this.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai, Osaka 590-8577, Japan
Jan. 2008 by Shimano Inc. PIT. SZK. Printed in Japan
C
These service instructions are printed on recycled paper.
Please note: Specifications are subject to change for improvement without notice. (English)

Especificaciones del producto

Marca: Shimano
Categoría: Accesorio para bicicleta
Modelo: CT-S500

¿Necesitas ayuda?

Si necesitas ayuda con Shimano CT-S500 haz una pregunta a continuación y otros usuarios te responderán


Accesorio para bicicleta Shimano Manuales

Shimano

Shimano FD-M985 Manual de Usario

8 Octubre 2024
Shimano

Shimano FD-M8000-L Manual de Usario

4 Octubre 2024
Shimano

Shimano FD-M6020-L Manual de Usario

30 Septiembre 2024
Shimano

Shimano RD-R7000-SS Manual de Usario

24 Septiembre 2024
Shimano

Shimano FD-M7000-10-E Manual de Usario

20 Septiembre 2024
Shimano

Shimano SL-A050-LN Manual de Usario

20 Septiembre 2024
Shimano

Shimano SM-RT70 Manual de Usario

16 Septiembre 2024
Shimano

Shimano SM-CA70 Manual de Usario

14 Septiembre 2024
Shimano

Shimano PD-M324 Manual de Usario

11 Septiembre 2024
Shimano

Shimano FD-M986 Manual de Usario

7 Septiembre 2024

Accesorio para bicicleta Manuales

Últimos Accesorio para bicicleta Manuales

Crivit

Crivit IAN 270384 Manual de Usario

10 Octubre 2024
Knog

Knog Oi Luxe Manual de Usario

26 Septiembre 2024
Lezyne

Lezyne Trigger Drive CO2 Manual de Usario

24 Septiembre 2024
Thule

Thule 973-23 Manual de Usario

22 Septiembre 2024
Abus

Abus WBA65 Manual de Usario

18 Septiembre 2024
Topeak

Topeak PRESSURE-RITE SHOCK ADAPTER Manual de Usario

17 Septiembre 2024
Blackburn

Blackburn Honest Digital Shock Manual de Usario

16 Septiembre 2024
Blackburn

Blackburn Grid Seat Bags Manual de Usario

16 Septiembre 2024
Blackburn

Blackburn Outpost Elite Manual de Usario

16 Septiembre 2024
Funn

Funn Ripper Manual de Usario

15 Septiembre 2024