StarTech.com ET90110WDM Manual de Usario

Lee a continuación 📖 el manual en español para StarTech.com ET90110WDM (1 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/1
Introduction
Thank you for purchasing a StarTech.com Single-Mode WDM Media
Converter. This product allows you to bridge two Ethernet networks
using fiber cable, and offers Wave Division Multiplexing, which allows
the use of a single fiber cable for both sending and receiving data
(Tx/Rx), reducing the amount of cable required.
Features
Simple installation and use
WDM (Wave Division Multiplexing) allows the use
of a single fiber cable for both sending and
receiving data
LED indicators display single-mode, multi-mode
and power status of the converter
Supports link-loss-forwarding function, loop-back test, remote
monitor status
Before You Begin
System Requirements
Fiber Cable
10Base-T; Cat 3, 4 or 5
or
100Base-Tx, Cat 5 or 6 cable
Power source
Contents (per unit)
Media Converter (1)
12V Power Adapter (1)
Instruction manual (1)
Basic Setup
1. Connect the fiber interface cable to the A-Unit. Using UTP cable,
connect the ethernet connection to the RJ45 jack.
2. Set the Fx switch (marked according to the specifications FIBER
of your fiber side equipment. The switch has two positions, HALF
(Half Duplex) and (FullDuplex). A Full Duplex setting will be FULL
indicated by anLED (see LED Indicators).
Media Converter Connections
The following example illustrates the connection scheme when con-
necting from a 10/100Base-TX port of one hub to a 100Base-FX port
of another hub, through the fiber converter:
The following example illustrates the connection scheme when con-
necting from a 10/100Base-TX port of one hub to a 100BASE-TX
Network Interface Card (NIC) in a computer through the fiber
converter:
Front Panel DIP Switch Settings
1. Full/ Half:
The Fiber Duplex will be configured in Full-duplex or Half-duplex
2. Loop-back test and get remote side status :
(NORM = Not Active, LBT ON = Active)
Please note: If the local side loop-back test is active, then LEDs
(except PWR) will all blink rapidly and refresh to display the remote
side status.
10/100 Mbps Single Mode WDM Media Converter
ET90110WDM (ET90110WDMA + ET90110WDMB)
Revised:7 June 2006 (A)
Support, Warranty Information, and Regulatory Compliance Statement
If you ever need help with your product, visit www.startech.com/support and access our com-
prehensive selection of online tools, documentation, and downloads. This product is backed by a
one-year warranty. In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase. During this period,
the products may be returned for repair, or replacement with equivalent products at our discre-
tion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products
from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability: In no event shall the liability of StarTech.com Ltd. and StarTech.com USA
LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any
pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for
the product. Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement may not
apply to you.
FCC Compliance Statement: This equipment has been tested and found to comply with the lim-
its for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
Consult the dealer or an experienced radio/TV technician for help.
Use RJ-45 jack to HUB
connection
Fiber Cable
10/100BASE-TX
UTP Connection
Fiber
Transceiver
connection
PWR
Fiber Full
Fiber Link
LAN 100
LAN Full
LAN Link
LED Function State Status
PWR Power Indicator On
Off
Converter has power
Converter has no power
Fiber Full Mode display On
Off
Fiber side full duplex mode (200mbps)
Fiber side half-duplex mode
Fiber Link Fiber link
On
Off
Blinking
The fiber link is okay
No link, or the link is faulty
Receiving data on the fiber
LAN 100 Mode display On
Off
UTP side is operating in 100Mbps mode
UTP side is operating in 10Mbps mode
LAN Full Mode display On
Off
UTP side full duplex mode (200mbps)
UTP side half-duplex mode
LAN Link Ethernet Link
On
Off
Blinking
The UTP link is ok
No link, or the link is faulty
Receiving data on Ethernet
LED Indicators
The following diagram and chart outline the meaning of each LED
located on the media converter(s):
NORM
FULL
FIBER
LBT ON
HALF
Wavelength Tx: 1310 nm / Rx: 1550 nm
BER <10-10
Sensitivity -32dBm
Outpout Power -18 dBm (A), -15dBm (B)
Power Margin 14 dB (A), 17dB (B)
Return Loss -14dBm
Supported Cable Type 9/125µm Single Mode (SC Connector)
Ethernet Network Interface 10/100 Mbits/sec. (via auto-negotiation)
Switching Mechanism Store and Forward
Additional Features Link-loss forwarding, loop-back test, remote
monitor status
Network Standards
Compliance
IEEE 802.3 10Base-T,
802.3u100Base-TX, 100Base-FX
MTBF 38000 hours (minimum)
Cable Length 20 KM (max) using single mode fiber optic cable
Product Dimensions (LxWxH)122mm x 85mm x 20mm (4.8 x 3.3 x 0.9 in.)
Product Weight 0.65 lb (295 g)
Data Transfer Rate (max.) 100 Mbits/sec (Full and Half duplex supported)
Certifications (regulatory etc.) FCC, CE (Class A)
Power Adapter DC 12V, 1A, Center Pos.
General Specifications

Especificaciones del producto

Marca: StarTech.com
Categoría: No categorizado
Modelo: ET90110WDM

¿Necesitas ayuda?

Si necesitas ayuda con StarTech.com ET90110WDM haz una pregunta a continuación y otros usuarios te responderán




No categorizado StarTech.com Manuales

No categorizado Manuales

Últimos No categorizado Manuales