StarTech.com PEX2S953 Manual de Usario

StarTech.com No categorizado PEX2S953

Lee a continuación 📖 el manual en español para StarTech.com PEX2S953 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: November 27, 2019 1:15 PM

Product Diagram (PEX2S953)

Port Function

1Serial Ports • Connect up to two Serial Devices

2Stand-os • Attach the to the Bracket PCI Express Serial Card

• Secure the to the Serial Cables Serial Ports

3Bracket • Attach the to the PCI Express Serial Card Computer

4PCI Express Bus

Connector

• Connect the to the PCI Express Serial Card

Computer Motherboard

5Jumper • Congure the individual power Serial Connector

settings

6LP4 Power Connector • Used to connect an LP4 Power Source

2-Port PCI Express Serial Card with 16950 UART

Requirements

For the latest requirements please visit

www.startech.com/PEX2S953.

• PCIe Slot

• Needle-Nose Pliers

• (Optional) LP4 Power Source

Installation

WARNING! PCI Express Serial Cards can be severely damaged by static

electricity. Make sure that you are properly grounded before you open the

Computer Case PCI Express Serial Card or touch the . You should wear an

Anti-Static Strap Anti-Static when you install any computer component. If an

Strap isn’t available, discharge any built-up static electricity by touching a large

Grounded Metal Surface PCI Express Serial for several seconds. Only handle the

Card by its edges and don’t touch the gold connectors.

Jumper Conguration

Note: This is specially designed to allow for power output PCI Express Serial Card

from the ninth pin of the for that support power Serial Connector(s) Serial Devices

over serial. conguration is a requirement when connecting Jumper Serial Devices

that require power through a .Serial Connector

The can be moved into one of three dierent positions in order to set the Jumper

power output voltage for the . The default setting for the Serial Connector Jumpers

is , no power. The must be connected after conguring theRI LP4 Power Connector

Jumper 5V 12V Jumper to or of power. To congure the , complete the following:

1. Ensure the isComputer’s Power O.

2. Determine the power setting that is required for .Port One

3. Locate the for and carefully lift the straight up and o of Jumper Port One Jumper

the .PCI Express Serial Card

Notes: The Jumper for Port 1 is labeled as J1 on the Printed Circuit Board.

Always hold the Card by the edges.

4. Position the over the set of that correspond with the desired Jumper Pins Serial

Connector Power Setting Jumper. See to determine where the Figure 1 should be

positioned.

5. Push the straight down and into place.Jumper

Note: Push the all the way into position for proper contact. Jumper

2 2

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

IC Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 0.5cm between the radiator and your body.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a lifetime warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: fr.startech.com

DE: de.startech.com

ES: es.startech.com

NL: nl.startech.com

IT: it.startech.com

JP: jp.startech.com

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

Hardware Installation

1. Ensure the is .Computer’s Power O

2. Unplug the .Computer‘s Power Cord

3. Remove the . Computer’s Cover

Note: For further information on how to remove the Computer’s Cover, refer to

the that came with the Manual Computer.

4. Remove the .Slot Bracket’s Holding Screw

5. Remove the corresponding from an available . Full-Height Bracket PCIe Slot

6. To install the , carefully align the PCI Express Serial Card PCI Express Serial Card’s

Bus Connector PCIe Slot Motherboard. PCI with the selected on the Push the

Express Serial Card Card PCIe down rmly to ensure the is properly seated into the

Slot.

7. (Optional - for power output from the ninth pin of the ) Connect Serial Connectors

the from the to the LP4 Power Connector Cable Computer’s Power Supply LP4

Power Connector Port PCI Express Serial Cardon the .

8. Replace the to secure the . Slot Bracket’s Holding Screw PCI Express Serial Card

9. Replace the and reconnect the . Computer’s Cover Power Cord

10. Download the latest .Drivers

Driver Installation

You can download the latest from the StarTech.com website:Drivers

www.startech.com/PEX2S953.

Navigate to the to locate the . Follow the instructions included Support Page Drivers

with the . Driver Files

6. Repeat these steps to congure the for Jumpers Port 2.

Notes: The for is labeled as on the .Jumper Port 2 J7 Printed Circuit Board

Recongure the PCI Express Serial Card for Low-Prole installations

1. Remove the four by twisting each one counterclockwise, using Stand-os Needle-

Nose Pliers.

2. Remove the . Bracket

3. Slide the over the . Low-Prole Brackets Serial Ports

4. Insert two through each and tighten by twisting each one Stand-os Bracket

clockwise, using .Needle-Nose Pliers

Figure 1

Jumper

Especificaciones del producto

Marca:	StarTech.com
Categoría:	No categorizado
Modelo:	PEX2S953

¿Necesitas ayuda?

Si necesitas ayuda con StarTech.com PEX2S953 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado StarTech.com Manuales

StarTech.com S322SAT3R Manual de Usario

23 Octubre 2024

StarTech.com 25S22M2NGFFR Manual de Usario

23 Octubre 2024

StarTech.com CABSHELFV2U-12-RACK Manual de Usario

23 Octubre 2024

StarTech.com 35FCREAD20BK Manual de Usario

23 Octubre 2024

StarTech.com 25SAT22MSAT Manual de Usario

23 Octubre 2024

StarTech.com 2CF2SATAR Manual de Usario

23 Octubre 2024

StarTech.com 35FCREADREM Manual de Usario

23 Octubre 2024

StarTech.com 35BAYCF2IDE Manual de Usario

23 Octubre 2024

StarTech.com PATA2SATA2 Manual de Usario

22 Octubre 2024

StarTech.com MSAT2SAT3 Manual de Usario

22 Octubre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024