Steren SN74LS47N Manual de Usario

Steren No categorizado SN74LS47N

Lee a continuación 📖 el manual en español para Steren SN74LS47N (8 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/8
Semiconductor Components Industries, LLC, 1999
December, 1999 – Rev. 6
1Publication Order Number:
SN74LS47/D
The SN74LS47 are Low Power Schottky BCD to 7-Segment
Decoder/Drivers consisting of NAND gates, input buers and seven
AND-OR-INVERT gates. They offer active LOW, high sink current
outputs for driving indicators directly. Seven NAND gates and one
driver are connected in pairs to make BCD data and its complement
available to the seven decoding AND-OR-INVERT gates. The
remaining NAND gate and three input buers provide lamp test,
blanking input/ripple-blanking output and ripple-blanking input.
The circuits accept 4-bit binary-coded-decimal (BCD) and,
depending on the state of the auxiliary inputs, decodes this data to
drive a 7-segment display indicator. The relative positive-logic output
levels, as well as conditions required at the auxiliary inputs, are shown
in the truth tables. Output congurations of the SN74LS47 are
designed to withstand the relatively high voltages required for
7-segment indicators.
These outputs will withstand 15 V with a maximum reverse current
of 250 µA. Indicator segments requiring up to 24 mA of current may
be driven directly from the SN74LS47 high performance output
transistors. Display patterns for BCD input counts above nine are
unique symbols to authenticate input conditions.
The SN74LS47 incorporates automatic leading and/or trailing-edge
zero-blanking control (RBI and RBO). Lamp test (LT) may be
performed at any time which the BI/RBO node is a HIGH level. This
device also contains an overriding blanking input (BI) which can be
used to control the lamp intensity by varying the frequency and duty
cycle of the BI input signal or to inhibit the outputs.
•Lamp Intensity Modulation Capability (BI/RBO)
•Open Collector Outputs
•Lamp Test Provision
•Leading/Trailing Zero Suppression
•Input Clamp Diodes Limit High-Speed Termination Effects
GUARANTEED OPERATING RANGES
Symbol Parameter Min Max UnitTyp
VCC Supply Voltage 4.75 5.0 5.25 V
TAOperating Ambient
Temperature Range
0 25 70 C°
I
OH Output Current – High
BI/RBO
– 50 A
IOL Output Current – Low
BI/RBO
BI/RBO
3.2 mA
VO(off) O–State Output Voltage
a to g
15 V
IO(on) On–State Output Current
a to g
24 mA
LOW
POWER
SCHOTTKY
SOIC
D SUFFIX
CASE 751B
http://onsemi.com
PLASTIC
N SUFFIX
CASE 648
16
1
16
1
Device Package Shipping
ORDERING INFORMATION
SN74LS47N 16 Pin DIP 2000 Units/Box
SN74LS47D 16 Pin 2500/Tape & Reel
SN74LS47
http://onsemi.com
2
LOGIC SYMBOL
CONNECTION DIAGRAM DIP (TOP VIEW)
BCD Inputs
Ripple–Blanking Input
Lamp–Test Input
Blanking Input or
Ripple–Blanking Output
Outputs
A, B, C, D
RBI
LT
BI/RBO
a, to g
0.5 U.L.
0.5 U.L.
0.5 U.L.
0.5 U.L.
1.2 U.L.
Open–Collector
0.25 U.L.
0.25 U.L.
0.25 U.L.
0.75 U.L.
2.0 U.L.
15 U.L.
NOTES:
a) 1 Unit Load (U.L.) = 40 A HIGH, 1.6 mA LOW.
b) Output current measured at VOUT = 0.5 V
b) The Output LOW drive factor is 15 U.L. for Commercial (74) Temperature Ranges.
HIGH LOW
(Note a)LOADING
PIN NAMES
14 13 12 11 10 9
1 2 3 4 5 6
VCC
7
16 15
8
f g a b c d e
B C LT BI / RBO RBI D A GND
VCC = PIN 16
GND = PIN 8
7 1 2 6 3 5
13 12 11 10 9 15 14 4
A B C D LT RBI
a b c d e f g
BI/
RBO
TRUTH TABLE
INPUTS OUTPUTS
SN74LS47
http://onsemi.com
3
14 15
LOGIC DIAGRAM
NUMERICAL DESIGNATIONS — RESULTANT DISPLAYS
0 1 2 3 4 5 6 7 8 9 10 11 12 13
INPUT
BLANKING INPUT OR
RIPPLE-BLANKING
OUTPUT
RIPPLE-BLANKING
INPUT
LAMP-TEST INPUT
A
B
C
D
a a
b b
c c
d d
e e
f f
g g
OUTPUT
DECIMAL
OR
FUNCTION
LT RBI D C B A BI/RBO a b c d e f g NOTE
0 H H L L L L H L L L L L L H A
1 H X L L L H H H L L H H H H A
2 H X L L H L H L L H L L H L
3 H X L L H H H L L L L H H L
4 H X L H L L H H L L H H L L
5 H X L H L H H L H L L H L L
6 H X L H H L H H H L L L L L
7 H X L H H H H L L L H H H H
8 H X H L L L H L L L L L L L
9 H X H L L H H L L L H H L L
10 H X H L H L H H H H L L H L
11 H X H L H H H H H L L H H L
12 H X H H L L H H L H H H L L
13 H X H H L H H L H H L H L L
14 H X H H H L H H H H L L L L
15 H X H H H H H H H H H H H H
BI X X X X X X L H H H H H H H B
RBI H L L L L L L H H H H H H H C
LT L X X X X X H L L L L L L L D
H = HIGH Voltage Level
L = LOW Voltage Level
X = Immaterial
NOTES:
(A) BI/RBO is wire-AND logic serving as blanking Input (BI) and/or ripple-blanking output (RBO). The blanking out (BI) must be open or
held at a HIGH level when output functions 0 through 15 are desired, and ripple-blanking input (RBI) must be open or at a HIGH level
if blanking of a decimal 0 is not desired. X = input may be HIGH or LOW.
(B) When a LOW level is applied to the blanking input (forced condition) all segment outputs go to a LOW level regardless of the state
of any other input condition.
(C) When ripple-blanking input (RBI) and inputs A, B, C, and D are at LOW level, with the lamp test input at HIGH level, all segment outputs
go to a HIGH level and the ripple-blanking output (RBO) goes to a LOW level (response condition).
(D) When the blanking input/ripple-blanking output (BI/RBO) is open or held at a HIGH level, and a LOW level is applied to lamp test input,
all segment outputs go to a LOW level.

Especificaciones del producto

Marca: Steren
Categoría: No categorizado
Modelo: SN74LS47N

¿Necesitas ayuda?

Si necesitas ayuda con Steren SN74LS47N haz una pregunta a continuación y otros usuarios te responderán


No categorizado Steren Manuales

Steren

Steren MOV-040 Manual de Usario

2 Septiembre 2024
Steren

Steren HER-700 Manual de Usario

2 Septiembre 2024
Steren

Steren MOR-015 Manual de Usario

1 Septiembre 2024
Steren

Steren ALA-003 Manual de Usario

1 Septiembre 2024
Steren

Steren SN74LS47N Manual de Usario

1 Septiembre 2024
Steren

Steren STV-036 Manual de Usario

1 Septiembre 2024
Steren

Steren SEG-300 Manual de Usario

1 Septiembre 2024
Steren

Steren ELI-035 Manual de Usario

31 Agosto 2024
Steren

Steren TEMP-24H/MINI Manual de Usario

31 Agosto 2024
Steren

Steren PS-828 Manual de Usario

31 Agosto 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024