Toa BS-1030B Manual de Usario

Toa Vocero BS-1030B

Lee a continuación 📖 el manual en español para Toa BS-1030B (4 páginas) en la categoría Vocero. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
The BS-1030 Series Speakers are small in size and feature the wide-band, high-quality, 2-way bass-reflex design which
makes them ideal for such applications as announcements and music reproduction.
BS-1030B
BS-1030W
UNIVERSAL SPEAKER
INSTRUCTION MANUAL
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully
before use.
• Make sure to observe the instructions in this manual as
the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual
handy for future reference.
WARN ING Indicates a potentially
hazardous situation which, if mishandled, could result in
death or serious personal injury.
• Use only the specified amplifier output voltage and
impedance, as exceeding the specified limits could result
in fire or other failures (high-impedance applications).
• To avoid accidental air explosions, do not use the unit
around gasoline, thinner or other combustibles.
• Install the unit only in a location that can structurally
support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and
causing personal injury and/or property damage.
• Do not use other methods than specified to mount the
bracket. Extreme force is applied to the unit and the unit
could fall off, possibly resulting in personal injuries.
• Use nuts and bolts that are appropriate for the ceiling's
or wall's structure and composition. Failure to do so may
cause the speaker to fall, resulting in material damage
and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the
bracket has no loose joints after installation to prevent
accidents that could result in personal injury.
• Attach the safety wire to the unit when mounting in
locations high above the ground. Failure to do so could
result in personal injury if the speaker should later fall for
any reason.
WARN ING Indicates a potentially
hazardous situation which, if mishandled, could result in
death or serious personal injury.
• Avoid mounting the unit in locations exposed to constant
vibration. The mounting bracket can be damaged by
excessive vibration, potentially causing the speaker to
fall, which could result in personal injury.
CAUTION Indicates a potentially hazardous
situation which, if mishandled, could result in moderate
or minor personal injury, and/or property damage.
• To avoid electric shocks, be sure to switch off the
amplifier power when connecting the speaker.
• Avoid installing the unit in humid or dusty locations, or in
locations exposed to heaters, solvents, acid, alkali,
smoke, or steam, as excessive exposure to these factors
could result in the speaker falling off, electric shock or
fire.
• Do not operate the unit for an extended period of time
with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate
and result in a fire.
• Do not stand or sit on, nor hang down from the unit as
this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
• Have the unit periodically checked by the shop from
where it was purchased. Failure to do so could result in
the speaker falling off due to damage or corrosion to the
speaker or its mounts, and possible personal injury.
2. FEATURES
• The speaker's smoothly curved surface permits it to
blend in with virtually all modern buildings.
• A built-in matching transformer permits the speaker to be
used for both high-impedance and low-impedance (8 Ω)
applications. The impedance can be easily changed from
outside the speaker.
• A splash-proof design enables the BS-1030 to even be
installed outdoors, in a location not directly exposed to
the elements, such as under eaves.
• Mountable to wall surfaces directly or using with supplied
or optional mounting brackets.
3. INPUT IMPEDANCE CHANGE
The speaker's input impedance is preset to 30 W (330 Ω)
of 100 V line by the factory. To change the impedance,
change the position of the rear panel-mounted rotary
switches with a slotted screwdriver.
3.1. High Impedance (70 V or 100 V Line) Applications
Set the [LINE VOL.] rotary switch to the 70 V or 100 V
position, and the [INPUT] rotary switch to the wattage to be
used. (The figure below is an example of 100 V, 20 W.)
30W
20W
15W
10W
5W 8
100V
70V
OFF
OFF
INPUT
LINE
VOL.
3.2. Low Impedance Applications
Set both the [LINE VOL] and [INPUT] rotary switches to
the [8 Ω] position.
Notes
To avoid damage to the speaker, be sure to follow the
instructions below.
•Switch off the amplifier power when changing the input.
•Never set the [INPUT] switch to the [8 Ω] position when
the [LINE VOL.] switch is set to the 70V or 100 V (high
impedance) position.
30W
20W
15W
10W
5W 8
100V
70V
OFF
OFF
INPUT
LINE
VOL.
4. SPEAKER INSTALLATION
4.1. Wall Mounting – With Surface-Mount Screws
Note: The surface-mount screws are not supplied with
the unit. Referring to the mounting hole's dimensional
diagram below, prepare the correct type of screws
appropriate to the wall material.
6 mm
16 mm
ø16 mm
Step 1. Install two surface-mount screws in the wall 50 mm
apart and leave them sticking out approximately 3
– 5 mm from the wall surface.
Step 2. Connect the speaker cable.
Step 3. Place the speaker's rear panel mounting holes
over the two installed screws to mount the speaker
to the wall surface.
Note
Route the speaker cable as
shown in the figure so that it is
not pinched between the speaker
and the wall surface.
Tip
When installing the speaker horizontally, use the relevant
mounting holes shown below.
1
2
3
Screw
(Please prepare
separately.)
Speaker cable
Mounting hole
3 5 mm–
Wall
50 mm
Mounting hole
4.2. Wall Mounting With Supplied Bracket –
Step 1. Attach the bracket to the speaker using the
supplied hardware.
Step 2. Mount the speaker in the desired location using the
mounting holes made in the bracket.
Note
Bracket mounting hardware is not supplied with the unit.
Referring to the bracket's dimensional diagram, prepare
the correct type of screws or bolts appropriate to the wall
material.
4.3. Mounting on the Optional ST-16 Speaker Stand
Step 1. Attach the bracket to the speaker using the
supplied hardware. (Refer to Section "4.2. Wall
Mounting With Supplied Bracket.") –
Step 2. Mount the speaker to the speaker stand through
the bracket's mounting holes.
4.4. Mounting with Other Brackets
The following table shows the brackets that can be used for
the BS-1030 Series Speakers. When using these brackets,
refer to their corresponding instruction manuals.
Bracket
(standard accessory)
Speaker
Plain washer
(standard accessory)
Machine screw
(standard accessory)
Speaker Bracket
(supplied with
the speaker)
Butterfly nut
(supplied with
the ST-16)
Washer
(supplied with
the ST-16)
Bracket
(supplied with the ST-16)
Hexagonal-head bolt
(supplied with the ST-16)
ST-16
(optional)
Usable Brackets
Speaker Mounting
Bracket SP-410
Speaker Mounting
Bracket SP-420
Wall/Ceiling Mounting
Bracket WCB-12
Wall/Ceiling Mounting
Bracket WCB-12W
Table Mounting
Bracket TMB-1
Table Mounting
Bracket TMB-1W
BS-1030B BS-1030W
OK
OK
OK
OK
OK
OK
OK
5. OUTDOOR INSTALLATION
PRECAUTIONS
The speaker's splash-proof construction permits it to be
installed outdoors, such as under eaves and other locations
where the speaker is not directly exposed to the elements.
However, because the splash-proof feature is strictly
dependent on speaker orientation, follow the mounting
instructions below.
5.1. Vertical Installation
5.2. Horizontal Installation
Note
The splash-proof function will not work with any other
installation method than those referred to above.
Install with the logo mark located at the bottom
of the front panel.
Horizontal
Face-down
Install the speaker so that its front panel
orientation stays in the above range.
Horizontal
Face-down
Install the speaker so that its
front panel orientation stays in
the above range.
Install with the logo mark located
at the right of the front panel as
viewed from the front.
The logo mark can be changed
to correct its orientation.

Especificaciones del producto

Marca: Toa
Categoría: Vocero
Modelo: BS-1030B

¿Necesitas ayuda?

Si necesitas ayuda con Toa BS-1030B haz una pregunta a continuación y otros usuarios te responderán


Vocero Toa Manuales

Toa

Toa F-1300B Manual de Usario

8 Octubre 2024
Toa

Toa F-1300WTWP Manual de Usario

3 Octubre 2024
Toa

Toa PC-391T Manual de Usario

26 Septiembre 2024
Toa

Toa PC-391 Manual de Usario

24 Septiembre 2024
Toa

Toa PC-1860EN Manual de Usario

24 Septiembre 2024
Toa

Toa PC-2360EN Manual de Usario

24 Septiembre 2024
Toa

Toa F-1300W Manual de Usario

24 Septiembre 2024
Toa

Toa HX-5B-WP Manual de Usario

20 Septiembre 2024
Toa

Toa PC-3WR Manual de Usario

19 Septiembre 2024
Toa

Toa TZ-205 Manual de Usario

19 Septiembre 2024

Vocero Manuales

Últimos Vocero Manuales

Continental Edison

Continental Edison CELED53HP20V2B4 Manual de Usario

27 Octubre 2024
Canton

Canton Vento 830.2 Manual de Usario

27 Octubre 2024
Jamo

Jamo S7-25C Manual de Usario

27 Octubre 2024
Bowers Wilkins

Bowers Wilkins 707 S2 Manual de Usario

27 Octubre 2024
Monacor

Monacor GLS-301/GR Manual de Usario

27 Octubre 2024
Monitor Audio

Monitor Audio Silver C150 Manual de Usario

26 Octubre 2024
FBT

FBT MITUS 210M Manual de Usario

26 Octubre 2024
CyberData Systems

CyberData Systems SIP 011398 Manual de Usario

26 Octubre 2024
Lamax

Lamax PartyGo1 Play Manual de Usario

26 Octubre 2024
IKEA

IKEA SYMFONISK 405.847.50 Manual de Usario

26 Octubre 2024