Tripp Lite DNET1 Manual de Usario

Tripp Lite No categorizado DNET1

Lee a continuación 📖 el manual en español para Tripp Lite DNET1 (12 páginas) en la categoría No categorizado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

Owner’s Manual

Network Dataline

Surge Suppressors

Tripp Lite World Headquarters

1111 W. 35th Street, Chicago, IL 60609 USA

(773) 869-1234 • www.tripplite.com

Note: Follow these instructions to ensure proper operation and prevent damage to this device

and its connected equipment.

Data Shield™ by Tripp Lite Network Dataline Surge Suppressors are designed to protect

data and communications equipment against AC transients caused by lightning, electrostatic

discharge and ground surges that can enter equipment from the signal lines or chassis ground.

Data Shield by Tripp Lite Network Dataline Surge Suppressors described here protect

networked equipment using 100Base-T, 10Base-T, 10Base-2 and Ethernet, Token Ring,

RS232, RS422, parallel, dial-up modems, fax, ISDN, DDS, T-1 and other communication

interfaces.

200810167 93-2858.indd 1 12/16/2008 9:58:50 AM

INSTALLATION

1. Make sure the computer, network device or other equipment is logged OFF the network

(if applicable). Turn OFF power to the equipment.

2. Disconnect the cable from the equipment to be protected.

3. Connect the Data Shield by Tripp Lite Network Dataline Surge Suppressor directly to the

equipment. DB9 and DB25 models are reversible, to work with male or female ports. To

change gender, remove the thumbscrews, reverse their direction and re-install.

4. Attach the green ground wire on the surge suppressor directly to the protected

equipment’s chassis. (Except DB9 and DB25 models.)

5. Reconnect the cable to the Data Shield by Tripp Lite Network Dataline Surge

Suppressor.

NOTE!

The Data Shield by Tripp Lite Network Dataline Surge Suppressor must be properly grounded and positioned as close

as possible to the equipment to be protected. For best results, it is required that the length of the signal line and ground

wire (if equipped) between the surge suppressor and the protected equipment be kept as short as possible, not to

exceed 12 inches (12”). It is best to install the surge suppressor directly to the equipment, as noted above.

NOTE!

Installing a typical Data Shield by Tripp Lite Network Dataline Surge Suppressor is equivalent to adding

approximately three feet (3’) of typical data communication cable to a segment.

CAUTION!

The Data Shield by Tripp Lite Network Dataline Surge

Suppressor does not protect the equipment on the opposite end

of the cable. Normally, protection at both ends is recommended.

CAUTION!

Use of this equipment in life support applications where failure

of this equipment can reasonably be expected to cause the

failure of the life support equipment or to signiﬁcantly affect its

safety or effectiveness is not recommended. Do not use this

equipment in the presence of a ﬂammable anesthetic mixture

with air, oxygen or nitrous oxide.

CAUTION!

When properly installed, the Data Shield by Tripp Lite Network

Dataline Surge Suppressor will only protect against surges on

the dataline portion of your installation. Simultaneous AC surge

suppression/power protection in the form of an ISOBAR® surge

suppressor or Tripp Lite UPS system is strongly recommended

for complete system/network protection and can also extend

Ultimate Lifetime Insurance coverage to connected equipment.

200810167 93-2858.indd 2 12/16/2008 9:58:51 AM

SPECIFICATIONS

All surge suppressors listed have component response times of less than 1 picosecond.

Model: Description:

Nominal

Clamping Voltage:

Peak Pulse

Current:

DRS232 RJ45/RJ11 protector for

100Base-T4, RS232 on twisted Pair

(wires 1-8) or ISDN “S/T” interfaces.

Supplied with a 4” RJ45 patch cable.

18 volts, protecting

wires 1-8 1340 amps

DNET1

RJ45 100Base-T, 10Base-T,

Token Ring, RS422, AS400/Sys3x

protector for NICs, hubs, routers,

etc. Supplied with 4” RJ45 patch

cable.

7.5 volts, protecting

wires 1-8 750 amps

DSUT1CSU

RJ45/RJ11 protector for nonspan

powered T-1 equipment, digital data

service CSUs/DSUs, ISDN “U”

interfaces or other digital lines.

Supplied with 4” RJ45 patch cable.

60 volts, protecting

wires 1-8 200 amps

DTEL2 RJ45/RJ11 for modems, answering

and fax machines. Supplied with

4” RJ11 patch cable.

260 volts, protecting center

4 wires (2 CO-lines) 250 amps

DB9

Serial DB9 RS232 protector for male

or female ports of data terminal and

computing equipment including PCs,

modems, etc. (Any male or female

9-pin port). Male/Female genders

are reversible with reversible

thumbscrews.

18 volts, protecting pins

1-9 and chassis 340 amps

DB25

Serial DB25 RS232 protector

(wires 1-8, 20) for male or female

ports of data terminal & computing

equipment including PCs, printers,

modems, etc. Male/Female genders

are reversible with reversible

thumbscrews.

18 volts, protecting pins

1-8, 20 and chassis 340 amps

DB25-ALL DB25-ALL: Serial DB25 RS232

protector (pins 1-25) for any 25-pin

male or female DTE/DCE ports.

Male/Female genders are reversible

with reversible thumbscrews.

18 volts, protecting pins

1-25 and chassis 340 amps

D10B2 10Base-2 thin coax protector (BNC

m/f). Also protects IBM 3270 and

CCTV lines.

7.5 volts, protecting center,

shield and chassis 750 amps

DCATV

Coaxial protector for TVs, VCRs, pro

video supplied by CATV (“F” m/f).

7.5 volts, protecting center

and shield conductors 750 amps

Call Tripp Lite Customer Support at (773) 869-1234 for additional applications.

200810167 93-2858.indd 3 12/16/2008 9:58:51 AM

Especificaciones del producto

Marca:	Tripp Lite
Categoría:	No categorizado
Modelo:	DNET1
Colocación del dispositivo:	Ingebouwd
Color del producto:	Roestvrijstaal
Bisagras de puerta:	Rechts
Pantalla incorporada:	Nee
Peso.:	51000 g
Ancho:	540 mm
Profundidad:	545 mm
Altura:	1771 mm
Longitud del cable:	2.45 m
Nivel de ruido:	35 dB
Consumo-anual-de-energía:	280 kWu
Peso del embalaje:	53000 g
Ancho del embalaje:	580 mm
Empaquetadura en profundidad:	608 mm
Altura del embalaje:	1840 mm
Clase de eficiencia energética (antigua):	A+
Capacidad bruta del congelador:	- l
Capacidad neta del congelador:	30 l
Capacidad de congelación:	3 kg/24u
Dirección de apertura de puerta intercambiable.:	Ja
Adecuado para ajuste de panel:	Nee
Capacidad neta del frigorífico:	262 l
Frigorífico de capacidad bruta:	- l
Iluminación interior del frigorífico:	Ja
tipo-de-lámpara:	LED
Número de estantes en el refrigerador.:	5
Número-de-cajones-para-verduras:	2
Posición del congelador:	Boven
Sin escarcha (congelador):	Nee
Tiempo de retención en caso de corte de energía:	16 uur
numero de estrellas:	4*
Capacidad neta total:	292 l
Botellero:	Ja
Descongelación automática (frigorífico):	Ja
Capacidad bruta total:	- l
Ancho del compartimento de instalación:	560 mm
Profundidad del compartimento de instalación:	555 mm
Altura del compartimento de instalación:	1776 mm
Bolsillos en las puertas del refrigerador:	5
Uso de energía por día:	0.767 kWh/24u
Actual:	16 A
Temperatura mínima de funcionamiento:	10 °C
Temperatura máxima (en funcionamiento):	43 °C
Clase-climática:	SN-T
voltaje-de-entrada-de-CA:	220 - 240 V
Frecuencia-de-entrada-de-CA:	50 Hz