Tripp Lite Isobar NSS-G24D2P24 Manual de Usario

Tripp Lite No categorizado Isobar NSS-G24D2P24

Lee a continuación 📖 el manual en español para Tripp Lite Isobar NSS-G24D2P24 (20 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/20
Owner’s Manual
Rackmount Managed
Network PoE Switch with
Built-in PDU and
® Surge Protection
Model: NSS-G24D2P24
(Series Number: AG-0139)
Español 7 • Français 13
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2016 Tripp Lite. All rights reserved.
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $100 value!
www.tripplite.com/warranty
16-05-219-9334E9.indb 1 5/19/2016 4:48:28 PM
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS!
This manual contains important instructions and warnings that should be
followed during the installation, operation and storage of this Tripp Lite product.
Failure to heed these warnings may affect your warranty.
PDU/Switch Location Warnings
• The switch is designed for indoor use only, in a controlled environment, away from excess
moisture, temperature extremes, conductive contaminants, dust or direct sunlight.
• For best performance, maintain an indoor temperature between 32º F and 104º F (0º C and
40º C) with relative humidity between 10% and 90% (non-condensing).
• Install in accordance with National Electrical Code standards. Be sure to use the proper
overcurrent protection for the installation in accordance with the plug/equipment rating.
• Leave adequate space around all sides of the switch for proper ventilation.
• Keep the switch away from high-frequency, strong-current devices (e.g., radio transmitting
stations, transmitters and broadband amplifiers).
• Use electromagnetic shielding (if required).
• For rackmount configuration, ensure both the rack and switch are properly grounded.
• If the switch is not rack mounted, securely place it on a sturdy, flat surface.
• The electrical outlets supplying power to the equipment should be installed near the equipment
and easily accessible.
• Improper installation can cause product damage that is not covered by the warranty.
• Do not expose the switch’s connected networking cables to outdoor elements.
• CAUTION – Do not install this device if there is not at least 30 feet (10 meters) or more of wire
between the electrical outlet and the electrical service panel.
• Do not use this product near water (e.g., in a wet basement, or near a swimming pool).
PDU/Switch Connection Warnings
• Use of this equipment in life support applications where failure of this equipment can
reasonably be expected to cause the failure of the life support equipment or to significantly
affect its safety or effectiveness is not recommended. Do not use this equipment in the
presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.
• Keep the switch’s input power off during installation.
• Use only the power cord that came included with the switch.
• Make sure the power supply voltage matches the specifications indicated on the switch.
• The total power requirement for equipment connected to the switch must not exceed the
maximum load rating for the PDU’s circuit breaker.
• Do not connect the switch to an ungrounded outlet or to extension cords or adapters that
eliminate the connection to ground.
• Do not drill into or attempt to open any part of the switch housing. There are no user-
serviceable parts inside.
• Do not attempt to modify the switch, including the input plugs and power cables.
• Do not attempt to use the switch if any part of it becomes damaged.
• Make sure network cables are properly seated. A clicking sound will be made when a cable is
installed correctly.
• If the power cord is damaged, do not attempt to connect the switch. Contact a Tripp Lite
Service Representative for assistance.
• Never attempt to install or use the switch during a thunderstorm.
16-05-219-9334E9.indb 2 5/19/2016 4:48:28 PM
3
Accessing the Management Configuration Interface
Product Features
12
Rear Panel:
Front Panel:
1 Gigabit Ethernet and PoE Ports: These 24 twisted-pair RJ45 ports support auto-negotiable
10/100/1000 Mbps and auto MDI/MDIX cross-over detection functions for true “plug and
play” capability. Any of the 24 RJ45 ports can be configured to supply up to 30 watts of PoE
(Power over Ethernet) power per port over existing network cables to attached devices like
VoIP phones, wireless access points, and surveillance cameras.
Note: The total PoE power available is limited to 240W.
2 An LED illuminates to indicate the switch is receiving power. Power ON/OFF LED:
3 This LED will illuminate solid green when the system is loading and will System Status LED:
blink to indicate the system is ready.
4 Of these 72 LEDs, 24 illuminate orange for 10/100 Mbps indicate Port Status LEDs:
connection status and blink to indicate activity on each port. When it discovers a 1000 Mbps
connection, the other 24 LEDs illuminate green to indicate connection status and blink to
indicate activity on each port. Also included in the array are 24 green LEDs that illuminate
when PoE is active per port. These PoE LEDs will blink to indicate a PoE fault or overload
condition per port.
14
5
9
10
3 6
8
2 7
11
After powering the switch for the first time, the Network Smart Switch can be configured using a
Web browser. To access the switch, the management computer and the switch must be set to the
same subnet. The IP address of the management computer must be configured manually. The
switch’s default IP address is 192.168.1.200 and the default subnet mask is 255.255.255.0.
The Network Smart Switch contains software for viewing, changing and monitoring how it works.
This management software is not required for the switch to function. The ports can be used
without the management software. However, the management software enables the setup
of VLAN, Trunking and additional features. The use of these features can also improve the
efficiency of the switch, which results in the improvement of its overall performance as well as the
performance of the network.
For more information about configuring the switch, visit www.tripplite.com to view the Network
Smart Switch Web Configuration Guide.
16-05-219-9334E9.indb 3 5/19/2016 4:48:29 PM

Especificaciones del producto

Marca: Tripp Lite
Categoría: No categorizado
Modelo: Isobar NSS-G24D2P24

¿Necesitas ayuda?

Si necesitas ayuda con Tripp Lite Isobar NSS-G24D2P24 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Tripp Lite Manuales

Tripp Lite

Tripp Lite EBP240V3501NB Manual de Usario

21 Octubre 2024
Tripp Lite

Tripp Lite SmartRack SR45UBEXPNDNR3 Manual de Usario

20 Octubre 2024
Tripp Lite

Tripp Lite SmartRack SRW12US Manual de Usario

19 Octubre 2024
Tripp Lite

Tripp Lite SmartRack SRWALLBRKT2U Manual de Usario

18 Octubre 2024
Tripp Lite

Tripp Lite B127A-1A1-BDBH Manual de Usario

12 Octubre 2024
Tripp Lite

Tripp Lite BP36V15-2U Manual de Usario

9 Octubre 2024
Tripp Lite

Tripp Lite RBC92-2U Manual de Usario

9 Octubre 2024
Tripp Lite

Tripp Lite SU6KRT3UX Manual de Usario

8 Octubre 2024
Tripp Lite

Tripp Lite SRCOMBO Manual de Usario

8 Octubre 2024
Tripp Lite

Tripp Lite PS-406-HGULTRA Manual de Usario

7 Octubre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024