V-Tac VT-77 Manual de Usario

V-Tac Lámpara VT-77

Lee a continuación 📖 el manual en español para V-Tac VT-77 (15 páginas) en la categoría Lámpara. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/15
WEEE Number: 80133970
INSTALLATION INSTRUCTION
LED SOLAR LIGHT
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
WARNING!
1. The light source of this luminaire is not replaceable;
when the light source reaches its end of life the whole
luminaire shall be replaced.
2. Installation should be done by certified electrician.
This marking indicates
that this product should
not be disposed of with
other household wastes
MULTI-LANGUAGE
MANUAL QR CODE
Please scan the QR code
to access the manual in
multiple languages.
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please
read these instructions carefully before starting the installation and keep this manual
handy for future reference. If you have any another query, please contact our dealer or
local vendor from whom you have purchased the product. They are trained and ready
to serve you at the best.The warranty is valid for 3 years from the date of purchase.
The warranty does not apply to damage caused by incorrect installation or abnormal
wear and tear. The company gives no warranty against damage to any surface due to
incorrect removal and installation of the product.
3
YEARS
WARRANTY
*
TECHNICAL SPECIFICATIONS
MODEL VT-77
WATTS 2W
LUMENS 220LM
BEAM ANGLE 170
CRI >80
IP RATING IP65
SOLAR LIGHT
EN
INSTALLATION DIAGRAM
Fixing
Bracket
Installation Instruction:
1. Drill two holes on the wall after confirming the installation position, then install the
expansion plug into the holes.
2. Put the screw into the expansion plug, do not screw to the end, it is ok if the screw
head is about 2-3mm away from the wall. If the installation surface is wood or soft
material, it can be screwed directly without using the expansion plug.
3. Put the mounting base into two screws on the wall. Then, tighten the base as
shown in Figure 1.
4. Install the lamp on the base, and it can be used.
Switch Function:
- Press and hold the button for 2-3 seconds to switch ON the solar light. Once
switched ON it will indicate a blue light.
- When switching on the solar light by default it will be in Mode 1.
- To enter Mode 2, press the button again.
- Pressing the button for the third time the solar light will switch OFF and the blue
light will disappear.
Operating Modes:
Mode 1: Sensor Mode
- At dusk, it automatically turns to 10% brightness.
- Turns on to 100% brightness when motion is detected in the range of <5 meters
- In 30 seconds if no motion is detected the light switches to 10% brightness.
- Turns off at the dawn.
Mode 2: Constant Brightness Mode
- The sensor will be disabled
- Automatically turns on at the dusk with 100% brightness and works constantly till
the battery capacity goes to Zero. (Upto 4 hours)
SOLAR LIGHT
EN
STRUCTURE AND SIZE
NOTES
1. This production is a solar energy product. When installing, the solar panels of the
product must
be illuminated in the direction of the sun. If not placed in the direction of the sun the
lamp will not function properly. Resulting in the lamp to no switch ON or the light is
functions for a short period of time only. Solar panel should be placed in the direction of
the sunlight. The performance of the light is the best if the illumination time of the
sunlight is longer than 6 hours resulting in the light to be turned on for its maximum
time.
2. This product is mainly installed on the wall and is not allowed to be used in damp or
immersed
places. Otherwise, it will have a breakdown and affect its service life.
3. The product can achieve the expected brightness and light-up time when the battery
is full of
electricity. Such as overcast and rainy days, which will cause insufficient charging and
shorten the
light-uptime. If the lighting time is not long on sunny days, please check whether the
solar panels
are exposed to the sun for a long time. Or whether the solar panel is dirty and dusty,
ensure to keep the solar panels clean.
4. LED Solar light is designed with a replaceable battery. It should be replaced after 3
years of use.
After removing the wire connection from the original lithium battery, the battery will be
removed and replaced with the new battery of the same specifications.
1. Solar Panel
14. Column
11. Fixing Side Base
15. Fixing Frame
13. Screw
12. Fixing
Bracket
2. Fixing frame
9. Fixing base
4. Litihium battery
6. Control panel
7. Switch button
8. LED
10. PC Cover
5. LED and battery
fixing box
3. Waterproof silicone
rubber ring

Especificaciones del producto

Marca: V-Tac
Categoría: Lámpara
Modelo: VT-77

¿Necesitas ayuda?

Si necesitas ayuda con V-Tac VT-77 haz una pregunta a continuación y otros usuarios te responderán




Lámpara V-Tac Manuales

Lámpara Manuales

Últimos Lámpara Manuales