Valcom VIP-130L Manual de Usario

Valcom Vocero VIP-130L

Lee a continuación 📖 el manual en español para Valcom VIP-130L (4 páginas) en la categoría Vocero. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
1 947628
ISSUE 3
VIP-130L IP Paging Horn
INTRODUCTION
The VIP-130L IP Paging Horn is a self contained
paging system which enables voice paging up to
1200 feet from an Ethernet connection. The
VIP-130L consist of a high efficiency 5 Watt
Class- Horn and a P-LLE Network Extender D VI
allowing stand alone capability when used with a
SIP enabled telephone System or can be
accessed from a variety of Valcom managed
VoIP products.
SPECIFICATIONS
Access Methods
PBX, FXO Port w/VIP-811
POTS telephone set w/VIP- 811
PBX, FXS Port w/VIP-821
Valcom M Cast Page Group
SIP enable telephone system –
Features
- network connection RJ 45
LED Status Indicator
Network activity LEDs
802.3af compliant
High Efficiency Class-D 5 Watt Amplifier
Dimensions/Weight
(Horn)
H x 00" W x 1 " D 7.00”10. 0.00
(18.75 cm H x cm W x cm D) 25.4 26.4
Weight: 8 lbs. ( 63 kg) 5. 2.
Network Extender
(VIP- ) LLE
0" W x 6. " D 1.30” H x 6.1 00
(3.51 cm H x 15.72 cm W x 13.51 cm D)
Weight: 0.85 lbs. (0.39 kg)
Nominal Specifications HORN –
Input Impedance: 600 Ohms
Input Level: -10dBm
Output Impedance: 600 Ohms
Output Level: -10dBm nominal
Nominal Specifications VIP- –LLE
Via 802.3af PoE Ethernet Switch:
Class 3 (12.95W)
Environment
Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating
Packing List
Qty
Item
1
VIP-LLE Network Extender
1
5 Watt High Efficiency Horn
1
VSP Document
2
Mounting Brackets
4
Rubber Pads
4
Wood Screws
1
RJ-45 Termination Block
1
RJ-45 Patch Cable
2 947628
CAUTION: To reduce the risk of electric shock,
Do not remove cover.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION
DO NOT OPEN
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.
INSTALLATION
FCC Information
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This
equipment generates, uses and can radiate
radio frequency energy and if not installed
and used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area may cause
harmful interference in which case the user
will be required to correct the interference at
his own expense.
Precautionary Designations
Mounting (VIP- )LLE
The VIP-L Network Extender is designed for LE
wall or shelf mounting and must be within 300
feet of the network switch.
Shelf: Provided with the VIP-L Network LE
Extender are four rubber pads. Peel the pads
from the carrier backing and place at the four
corners of the bottom of the unit.
Wall: Using the brackets and wood screws
provided, secure the VIP-L Network Extender LE
to the wall.
Mounting (HORN)
The horn should be mounted 15 to 20 feet
above the floor to allow for best sound
distribution. The unit can be mounted to a wall,
a beam or an electrical box.
NOTE: For ease of installation, the base can be
attached to the speaker before or after the base
is mounted.
Loosen position adjustment knob
Insert the ball of the base into the socket
of the speaker
Tighten the position adjustment knob
Mount the base to a wall using the two
holes provided. Knockout holes are
provided for punch out should additional
holes be desired.
clamp is provided with the horn to A “C”
allow mounting to a beam. Place the
bolt through the hole in the bottom of the
base to secure the “C” clamp to the
beam. It is suggested that the horn be
mounted to the underside of the “I”
beam to provide maximum positioning
adjustments.
Connection to an electrical backbox is
accomplished by channeling wire
through the ball of the base and making
appropriate connections. The base has
holes punched for a double-gang square
box, but by punching out additional
knockout holes, the base can be
mounted to a single-gang or octagon
box
The horn may be rotated or moved up and down
to obtain the desired position by loosening the
position adjustment knob at the bottom of the
unit approximately one turn. Make required
adjustments and re- en knob. tight
Interconnections
The method of powering the VIP-130 IP only L
Paging Horn is via a power over Ethernet switch
or power injector meeting the 802.3af
specification .
Make all required signal connections before
connecting to Ethernet switch or power injector
meeting the 802.3af specification. Power is
supplied to the horn assembly via the
VIP-L Network Extender. LE
3 947628
W/BL W/O W/GN W/BR
900' MAX DISTANCE
CAT 3/5/6
BLORBK
RD
GYBRYL
GN
W/BR PAIR
BL/W
W/BL
W/GN PAIR
*W/O PAIR NOT USED
Amplified
Paging Horn
RJ-45
Termination Block
V
Act
Status
Link
VIP-LLE
ALCOM
Signal Connections (Fig. 1)
Connect CAT- cable from rear panel color 5 the
coded connector of the VIP-L Network LE
Extender to the supplied RJ-45 termination block
(900 feet maximum distance). Use the supplied
CAT-5 patch cable to connect the -RJ 45
connector of horn to RJ-45 termination block.
Network Connection (Fig. 1)
The VIP-L Network Extender has one CAT-5 LE
RJ- connector on the front panel 45 “NETWORK”
and one CAT- color-coded connector on the 5
rear panel.
Use the supplied CAT-5 patch cable to connect
the NETWORK connector of the VIP-LLE
Network Extender to a 802.3af compliant PoE
port (300feet maximum distance).
Status Indicator Lights
The VIP-LLE Network Extender has 3 status
indication lights:
STATUS: Flashes during normal operation, and
solid when unit in reset.
LINK: Indicates 100 Mbit Ethernet connection
when illuminated. No activity indicates 10 Mbit
connection.
Act: Indicator flashes to indicate network
activity
Operation
Provide paging from SIP connection or via a
variety of Valcom managed VoIP products.
Integration to customer telephone system can
be via SIP registration, FXO port (with VIP-811),
or FXS port (with VIP-821).
Front View
Rear View
Figure 1

Especificaciones del producto

Marca: Valcom
Categoría: Vocero
Modelo: VIP-130L

¿Necesitas ayuda?

Si necesitas ayuda con Valcom VIP-130L haz una pregunta a continuación y otros usuarios te responderán


Vocero Valcom Manuales

Valcom

Valcom VIP-421 Manual de Usario

19 Septiembre 2024
Valcom

Valcom InformaCast VIP-120-IC Manual de Usario

19 Septiembre 2024
Valcom

Valcom InformaCast VIP-402A-IC Manual de Usario

19 Septiembre 2024
Valcom

Valcom VIP-422A Manual de Usario

19 Septiembre 2024
Valcom

Valcom V-1019B Manual de Usario

19 Septiembre 2024
Valcom

Valcom V-1020C Manual de Usario

19 Septiembre 2024
Valcom

Valcom S-522A-2 Manual de Usario

19 Septiembre 2024
Valcom

Valcom Clarity S-515 Manual de Usario

19 Septiembre 2024
Valcom

Valcom V-1023C Manual de Usario

19 Septiembre 2024
Valcom

Valcom V-1040 Manual de Usario

19 Septiembre 2024

Vocero Manuales

Últimos Vocero Manuales

Continental Edison

Continental Edison CELED53HP20V2B4 Manual de Usario

27 Octubre 2024
Canton

Canton Vento 830.2 Manual de Usario

27 Octubre 2024
Jamo

Jamo S7-25C Manual de Usario

27 Octubre 2024
Bowers Wilkins

Bowers Wilkins 707 S2 Manual de Usario

27 Octubre 2024
Monacor

Monacor GLS-301/GR Manual de Usario

27 Octubre 2024
Monitor Audio

Monitor Audio Silver C150 Manual de Usario

26 Octubre 2024
FBT

FBT MITUS 210M Manual de Usario

26 Octubre 2024
CyberData Systems

CyberData Systems SIP 011398 Manual de Usario

26 Octubre 2024
Lamax

Lamax PartyGo1 Play Manual de Usario

26 Octubre 2024
IKEA

IKEA SYMFONISK 405.847.50 Manual de Usario

26 Octubre 2024