Vemer HR-1P3D Manual de Usario

Lee a continuación 📖 el manual en español para Vemer HR-1P3D (26 páginas) en la categoría No categorizado. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/26
- 27 -
User Manual Regulators
English
Contents
Safety warnings Page 28
Technical specifications Page 28
Description of instrument Page 31
Electrical connections Page 31
Glossary Page 32
Operation Page 37
Setting the regulation parameters Page 37
Parameter menu Page 39
Error messages Page 46
Reference standards Page 47
Dimensions and connection diagrams, 33x75 mm Page 48-49
Dimensions and connection diagrams, 72x72 mm Page 50
Dimensions and connection diagrams, 4-DIN Page 51
- 28 -
User Manual Regulators
English
During the installation and operation of the instrument, follow the
instructions set out below:
1) The instrument should be installed by a skilled operator.
2) Strictly follow the connection diagrams when installing the instrument.
3) Do not power or connect the instrument if any part of it is damaged.
4) Before touching the terminals, make sure the wires to be connected to
the instrument are not live.
5) The connection cables should be able to resist the maximum operating
temperature (Tmax), obtained from the sum of the maximum ambient
temperature (Ta) + a temperature of 20 °C (Tmax= Ta + 20 °C).
6) The instruments guarantee a main insulation between the low voltage
(250 V) and very low voltage parts.
7) Any outside switches connected to the controls should guarantee a
minimum insulation at operating temperature of 250 V AC, or should be
protected by equivalent insulation.
8) Contacts: all type 1C (CEI 107-70 and variants).
9) The instruments require no maintenance.
Series of digital regulators used for the most simple requirements in the control
and regulation of humidity and pressure levels in air conditioning, heating
and refrigeration systems
Two dedicated base models for pressure and humidity control:
- DIGITAL HUMIDITY REGULATORS HR
- DIGITAL PRESSURE REGULATORS PR
Each single model has 1 probe input for the connection of active sensors
with standardised 0÷20 mA, 4÷20 mA and 0÷1 V outputs
The power supply to the active probe (linear sensor) comes directly from
the instrument: 9 V DC available
For each single model, the probe input can be configured from the keyboard
Available in versions with 1 or 2 relay outputs with contact in exchange
Regulators with 3 digit, seven segment and decimal point display
Relay intervention warning lamp
Display range: -99 ÷ +999
Display resolution: 0.1 RH or bar (-9.9 ÷ +99.9 RH or bar)
and 1 RH or bar (< -9.9 °C and > +99.9 RH or bar)
Precision: ±0.5 % of the end of scale value ±1 digit
(at an ambient temperature of 23 °C)
Sampling time: 0.5s
TECHNICAL SPECIFICATIONS
SAFETY WARNINGS
- 29 -
User Manual Regulators
English
Parameter setting in digital mode:
- Set point
- Differential
- Neutral zone
- Output drive timing
- Digital input delay function and time
- Alarm delay / buzzer enable time
- Probe calibration offset
- Resolution displayed
- Measurement display filter (update speed)
- Type of probe input
- Password
- Operating modes (regulation):
ON/OFF Direct and/or Reverse action with or without neutral zone
PWM Direct and Reverse action with or without neutral zone
— ALARM
Special mode
2 independent set points
Digital input: 1 (not versions HR-..P7A, PR-..P7A) for outside consensus
for configurable function: outside alarm, regulator ON/OFF, set-point switching,
Direct/Reverce switching, etc.
Acoustic and visual alarm signalling for: outside alarm (from digital input),
probe alarm (malfunction), minimum or maximum alarm
Infrared receiver with RC-5 protocol for remote control (accessory available
separately for remote programming)
Available in the following fixing versions: 33x75 mm rear panel, 72x72 mm
rear panel and modular 4 DIN
Power supply: see table on the following page
Rated power: 3 VA for models with 33x75 mm rear panel fixing
4.5 VA for models with 72x72 mm and modular 4 DIN fixing
Max absorption: 100 mA at 12 V - 50 mA at 24 V (1 channel)
Operating temperature: 0 ÷ +50 °C
Operating humidity: <80%
Storage temperature: -10 ÷ +70 °C (<80% RH)
Protection level: front panel IP54 (IP40 for the 4 DIN module version)
terminals IP20

Especificaciones del producto

Marca: Vemer
Categoría: No categorizado
Modelo: HR-1P3D
Color del producto: Zwart
Peso.: 229 g
Ancho: 145 mm
Profundidad: 20 mm
Altura: 90 mm
Manual de usuario: Ja
Bluetooth: Nee
Diagonal de la pantalla: 5 "
Resolución: 480 x 272 Pixels
Pantalla táctil: Ja
Relación de aspecto original: 16:9
factor vorm: Handheld/Fixed
Tipo de fuente de energía: Battery, Cigar lighter
Cables suministrados: USB
Tarjetas de memoria compatibles: MicroSD (TransFlash)
Guía de inicio rápido: Ja
Altavoces incorporados: Ja
Duración de la batería/duración de la batería: 2 uur
Tipo de medio de almacenamiento: Flash
Cámara integrada: Nee
Idiomas soportados: Multi
Bandas de frecuencia soportadas: Niet ondersteund
Antena: Intern
Baterias-incluidas: Ja
Pantalla ancha: Ja
Agua: Nee
Deportes (fitness, correr): Nee
Exterior: Nee
Geocaching: Nee
Auto: Ja
Para volar: Nee
Bicicleta: Nee
Camión: Nee
Autocaravana/caravana: Nee
Golf: Nee
Guía de carril: Ja
Incluyendo carpetas: Ja
Cobertura del mapa: Geheel Europa
Canal de mensajes de tráfico (TMC): Nee
Opciones de vista de mapa: 2D/3D
Nombres de calles hablados: Ja
Número de países cubiertos: 45
Tráfico TomTom de por vida: Ja
Búsqueda rápida: Ja
Toca y listo: Ja

¿Necesitas ayuda?

Si necesitas ayuda con Vemer HR-1P3D haz una pregunta a continuación y otros usuarios te responderán




No categorizado Vemer Manuales

No categorizado Manuales

Últimos No categorizado Manuales