Viking DEV900 Manual de Usario

Viking campana extractora DEV900

Lee a continuación 📖 el manual en español para Viking DEV900 (12 páginas) en la categoría campana extractora. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer or your distributor.

2. Before servicing or cleaning unit, switch power oﬀ

at service panel and lock the service disconnect-

ing means to prevent power from being switched

on accidentally. When the service disconnecting

means cannot be locked, securely fasten a promi-

nent warning device, such as a tag, to the service

panel.

3. Installation work and electrical wiring must be done

by a qualiﬁed person(s) in accordance with all ap-

plicable codes and standards, including ﬁre-rated

construction codes and standards.

4. Suﬃcient air is needed for proper combustion and

exhausting of gases through the ﬂue (chimney) of

fuel burning equipment to prevent backdrafting. Fol-

low the heating equipment manufacturer's guideline

and safety standards such as those published by

the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigera-

tion and Air Conditioning Engineers (ASHRAE),

and the local code authorities.

WARNING

CAUTION

1. For general ventilating use only. Do not use to

exhaust hazardous or explosive material and

vapors.

2. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, con-

struction dust, etc. oﬀ power unit.

3. Please read speciﬁcation label on product for

further information and requirements.

4. Electrical circuit, including speed control, (if used),

must be rated 6 AMPS minimum.

Blower Dimensions

28.25 x 24.75 x 7.17

PLAN THE INSTALLATION

1. Locate the ventilator so the length of the duct

run and number of elbows needed are kept to a

minimum.

2. Where possible, ventilator should be centered

between wall studs or roof rafters.

3. Avoid pipes, wires, or other ductwork that may be

running through the wall.

ALL INSTALLATIONS

MODEL VOLTS AMPS CFM DUCT SIZE

DEV900 120 5.7 900 10 " DIA.

SPECIFICATIONS

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 4

5. When cutting or drilling into wall, or ceiling, do not

damage electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the out-

doors.

7. To reduce risk of ﬁre, use only metal ductwork.

8. This unit must be grounded.

READ AND SAVE THESE INSTRUCTIONS

VIKING MODEL DEV900

EXTERIOR MOUNTED VENTILATOR

FOR USE WITH VCWH, VICH, DBCV, DICV, DCWH, DCWL, DCWN, DTWS AND

DCIH RANGE HOODS. :-/-2+ 00' 30" TO 42" WIDE, TO 18" HIGH.9"

11" dia.

hole

7¼"

1¼"

dia. hole

10¾"

24¾"

28¼"

Wa ll Stu d

REMOVE

SIDING

8½"

Pilot

Hole

Pilot

Hole

OUTSIDE - WALL VIEW

1. Locate the ventilator on the rear slope of the roof.

Place it in a location to minimize duct run. The

location should be free of obstacles (T.V. leads,

electrical lines, etc.). Bear in mind, if the ventilator

top is level with the roof peak, it will not be seen

from the street. Keep this approximate location in

mind as you work from within the attic.

1. Choose a position on the outside wall. Make sure

that no wall studs, pipes or wires run through the

opening area.

PREPARE THE INSTALLATION

LOCATION

ROOF INSTALLATIONS

PREPARE THE INSTALLATION

LOCATION

WALL INSTALLATIONS

ALL INSTALLATIONS

5. For ﬂat roof installations, build a curb that will mount

the ventilator at a minimum pitch of 2/12. See

Figure 2. Discharge end of the ventilator should

be pointed away from prevailing winds.

20½"

8½"

20¾"

7¼"

1¼"

dia. hole

Roof Rafter

REMOVE

SHINGLES

11"

dia.

hole

Roof Rafter

Pilot

Hole

Pilot

Hole

OUTSIDE - ROOF VIEW

From inside the attic space:

2. Drill a PILOT HOLE up through the roof, 8½"

from the of a .inside edge ROOF RAFTER

From outside - on the roof:

3. Measure and mark the 20¾" x 20½" rectangle.

Cut and remove only the shingles inside this

rectangle.

4. Measure and mark the 11" DIAMETER HOLE

and the 1¼" DIAMETER HOLE. Cut these holes

all the way through the roof.

Figure 1

PREPARE THE VENTILATOR

1. Unpack the ventilator assembly.

2. Remove the cover and screws.

3. Remove and discard cardboard from ventilator

wheel.

4. Remove the wiring box cover and screws.

5. Attach an appropriate U.L. approved cable con-

nector in the hole at the rear of the wiring box.

From inside the wall:

2. Drill a PILOT HOLE through the wall, 8½" from

the of a inside edge WALL STUD.

From outside - on the wall:

3. Measure and mark the 25" x 29½" rectangle.

Cut and remove only the siding inside this

rectangle.

4. Measure and mark the 11" DIAMETER HOLE

and the 1¼" DIAMETER HOLE. Cut these holes

Figure 3

6¾"

28¼"

24 ¾"

Figure 2

1. Remove rooﬁng nails from the upper 2/3 of the

shingles around the cutout area and carefully lift

the shingles to allow the back ﬂashing sheet on

the ventilator housing to ﬁt under them.

2. Center the ventilator ring in the 11" diameter hole,

making sure that the 1-1/4" diameter electrical wir-

ing hole aligns with the hole in the wiring box.

3. Attach the ventilator to the roof with the six screws

provided. All six holes in the back panel must be

ﬁlled, or any moisture that may get inside the ven-

tilator housing could leak into the house.

4. Using a good grade of rooﬁng cement, seal all of

the shingles around the housing and ﬂashing sheet

as well as the mounting screw heads.

5. Bring electrical wiring through the hole in the wiring

box and secure it according to local codes.

6. Make the electrical connections with the proper

connector for the type of wiring being used. Con-

nect white to white, black to black, and the green

or bare wire to green. See Figure 4.

7. Replace wiring box cover and screws. Do not pinch

wiring under the cover.

8. Check for free movement of the damper before

installing housing cover and screws.

1. Place a large bead of caulk on the back side of

the housing along the outer edge.

2. Center the ventilator ring in the 11" diameter hole,

making sure that the 1-1/4" diameter electrical

wiring hole aligns with the hole in the wiring box.

3. Attach ventilator to the wall with the six screws

provided. All six holes in the back panel must

be ﬁlled, or any moisture that may get inside the

ventilator housing could leak into the house.

4. Using a good grade of caulk, seal all around the

mounting screw heads.

5. Bring electrical wiring through the hole in the wiring

box and secure it according to local codes.

6. Make the electrical connections with the proper

connector for the type of wire being used. Connect

white to white, black to black, and green or bare

wire to green. See Figure 4.

7. Replace wiring box cover and screws. Do not pinch

wiring under cover.

8. Check for free movement of the damper before

installing housing cover and screws.

9. Top and side ﬂanges of the back plate may be

covered with trim strips. Do not block grille open-

ing at bottom with trim. It will adversely aﬀect

performance of the ventilator.

INSTALL THE VENTILATOR

ROOF INSTALLATIONS

INSTALL THE VENTILATOR

WALL INSTALLATIONS

Figure 4

120 VAC

LINE IN

BLACK

WHITE

GREEN

Especificaciones del producto

Marca:	Viking
Categoría:	campana extractora
Modelo:	DEV900
Color del producto:	Roestvrijstaal
Altura:	70 mm
Mango de color:	Roestvrijstaal
Diámetro:	200 mm
Cantidad de embarcaciones:	1
Material:	Roestvrijstaal
Contenido:	1.4 l
Recubrimiento antiadherente:	Ja
Incluye tapa:	Nee
Recubrimiento interno:	Roestvrijstaal