Vivotek AW-IHT-0601 Manual de Usario

Vivotek No categorizado AW-IHT-0601

Lee a continuación 📖 el manual en español para Vivotek AW-IHT-0601 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
1. Install the switch in a ventilated and dry place that is free of electromagnetic source, vibration, moisture, and dust.
2. Make sure the ventilation openings on the switch are not blocked.
3. Use ber optic cables and transceiver compliant with the following: Multi-mode: 50/125um, 62.5/125um, 850nm;
Single-mode): 9/125um ,1310nm.
4. DC input: (AW-IHT-0600 - 44V~56VDC; AW-IHT-0601 - 12~56VDC). Follow the printed polarity for V+, V-, and Ground.
AW-IHT-0600 Industrial PoE Switch
AW-IHT-0601
Quick Installation Guide
The AW-IHT-0600 series is a rugged media PoE switch designed for delivering a max. of 30 watts to powered devices.
The optional TX or FX uplink port can be used to extend the connection to a remote site. With its multi-purpose design, it
is t for IP surveillance, trafc monitoring, and security applications in critical environments. The machine features a total
budget of 126 watts and a wide range of operating temperatures ranging from -40°C to 75°C.
IMPORTANT:
INTRODUCTION
CONNECTION
* 1x PoE switch * 1x Quick Installation Guide * 1x 6-pin terminal block
* 2x wall mount brackets * 1x DIN rail bracket
PACKAGE CONTENTS
1. Pull out the 6-pin terminal block.
2. Connect positive wires to V+, negative wires to V-, and
neutral wire to the ground screw.
Connect the 24V DC @1A pins to external devices.
When 2 power pins are connected, the relay is shorted.
When any of them is diconnected, the relay connection
is open.
3. Connect SFP transceivers and ber cables to the ber
ports.
4. Install the 6-pin terminal block.
1 2
ON
F5 1000M
T5 100M
DIP 1 F5 Enable the F5 ber port (default)
T5 Enable the T5 Ethernet port
DIP 2 1000M The F5/T5/F6 port in the Gigabit mode (default)
100M The F5/F6 ber port in the 100Mbit mode. If T5 (Ethernet) is put to use, the
T5 port can not operate in the 100Mb mode.
WARNING - Always ground the power source to maintain a clean power input.
- OR -
LAN/WAN
T5
F5
PW1 ON When power is connected.
PW2 ON When power is connected.
ERR (relay) OFF When both PW1 and PW2 are
connected.
ON Only PW1 or PW2 is connected.
F5 ON Port 5 ber is detected.
OFF Port 5 ber is not detected.
Flashing Data is being transmitted or received.
F6 ON Port 6 ber is detected.
OFF Port 6 ber is not detected.
Flashing Data is being transmitted or received.
Link ON TX link is detected.
OFF Link is not detected.
Flashing Port is active.
SPD ON 1000M speed is detected.
OFF 10/100M speed is detected.
P1,P2,P3,
P4
ON PD is detected on the designated port.
OFF No PD is detected.
LED DEFINITIONS
IMPORTANT - You can either use the F5 ber or the T5 Ethernet port. These ports can not be
used at the same time. Use the DIP switch to make the selection.
Note that the conguration change only takes effect after a power cycle.

Especificaciones del producto

Marca: Vivotek
Categoría: No categorizado
Modelo: AW-IHT-0601

¿Necesitas ayuda?

Si necesitas ayuda con Vivotek AW-IHT-0601 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Vivotek Manuales

No categorizado Manuales

Últimos No categorizado Manuales