Whirlpool ADG 8798 A+ PC IX Manual de Usario

Whirlpool lavavajillas ADG 8798 A+ PC IX

Lee a continuación 📖 el manual en español para Whirlpool ADG 8798 A+ PC IX (8 páginas) en la categoría lavavajillas. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

GB -1-

-1-

-1--1-

Chart

(see at right for options description)

(see at right for options description)(see at right for options description)

PROGRAM SELE

PROGRAM SELEPROGRAM SELECTION

CTION

CTION CTION

BUTTON

BUTTONBUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

STSTART/RESUME BUTTON

ART/RESUME BUTTON

ART/RESUME BUTTONART/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program.

When the door is opened during a washing cycle,

the cycle is temporarily paused: the Start indicator

blinks. To resume the cycle close the door and

push Start button again.

CANCEL/OFF BU

CANCEL/OFF BUCANCEL/OFF BUTTON

TTON

TTONTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

1)1) Program data obtained in conformity with

Program data obtained in conformity with

Program data obtained in conformity with Program data obtained in conformity with European standard EN 50242, obta

European standard EN 50242, obta

European standard EN 50242, obtaEuropean standard EN 50242, obtained under normal conditions (with

ined under normal conditions (with

ined under normal conditions (withined under normal conditions (without any options) a

out any options) a

out any options) aout any options) and may vary depending on conditions. Differences of up

nd may vary depending on conditions. Differences of up

nd may vary depending on conditions. Differences of up nd may vary depending on conditions. Differences of up

to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2)2) Reference program for energy label in compliance with EN 50242 re

Reference program for energy label in compliance with EN 50242 re

Reference program for energy label in compliance with EN 50242 reReference program for energy label in compliance with EN 50242 regulations. - Note for T

gulations. - Note for T

gulations. - Note for Tgulations. - Note for T

esting Institutes: for detailed infor

esting Institutes: for detailed inforesting Institutes: for detailed information on the EN/Standard loading compari

mation on the EN/Standard loading compari

mation on the EN/Standard loading comparimation on the EN/Standard loading comparison test

son test

son test son test

and other tests

and other testsand other tests, contact the fo

, contact the fo

, contact the fo, contact the following add

llowing add

llowing addllowing address: “nk_cus

ress: “nk_cus

ress: “nk_cusress: “nk_customer@whirl

tomer@whirl

tomer@whirltomer@whirlpool.com”.

pool.com”.

pool.com”.pool.com”.

3)3) The antibacterial action has been tested by the Institut P

The antibacterial action has been tested by the Institut P

The antibacterial action has been tested by the Institut PThe antibacterial action has been tested by the Institut Past

ast

astasteur of Lille (France), based on the NF EN 13697 standard of Nove

eur of Lille (France), based on the NF EN 13697 standard of Nove

eur of Lille (France), based on the NF EN 13697 standard of Noveeur of Lille (France), based on the NF EN 13697 standard of November 2001.

mber 2001.

mber 2001.mber 2001.

RECYCLING W

RECYCLING WRECYCLING WA

AATER SYSTEM: these programs save water in a dedicated tank.

TER SYSTEM: these programs save water in a dedicated tank.

TER SYSTEM: these programs save water in a dedicated tank.TER SYSTEM: these programs save water in a dedicated tank.

A T

A TA TANK CLEANING CY

ANK CLEANING CY

ANK CLEANING CYANK CLEANING CYCLE (at least 45 min.) is automatically run

CLE (at least 45 min.) is automatically run

CLE (at least 45 min.) is automatically runCLE (at least 45 min.) is automatically run ever

ever

ever every 30 cycles or after every power off, to assure the best prod

y 30 cycles or after every power off, to assure the best prod

y 30 cycles or after every power off, to assure the best prody 30 cycles or after every power off, to assure the best product cond

uct cond

uct conduct conditions.

itions.

itions.itions.

TTable of programs

able of programs

able of programsable of programs Deter

Deter

DeterDeter-

gent

gentgent

Consumption

ConsumptionConsumption Drying

Drying

DryingDrying

Phase

PhasePhase

Programs

ProgramsPrograms Available

Available

AvailableAvailable

options

optionsoptions Loading instructions

Loading instructions

Loading instructionsLoading instructions

Litres

LitresLitres kWh

kWh

kWhkWh Minutes

Minutes

MinutesMinutes 1)

1)1)

P1P1 6th Sen

6th Sen

6th Sen6th Sense

se se

Pow

PowPowe

eer

rr C

C Cl

lle

eean

anan 40°-70°C

40°-70°C

40°-70°C40°-70°C Delay

Multizone

Power Clean

Use for normal soiled dishes with dried-on food.

Senses the level of soiling on the dishes and adjusts

the program accordingly. When the sensor is

detecting the soil level an animation appears in the

display and the cycle duration is updated. The

Power Clean option is activated automatically with

this program. To deactivate, press the Power

Clean button on the control panel.

X 7-14 1.00-1.65 80-165 Full

P2P2

Pre-

Pre-Pre-Wash

Wash

WashWash cold

cold

coldcold Delay

Multizone Crockery to be washed later. — 4.0 0.03 14 NO

P3P3

Frag

FragFragile

ile

ileile 40°C

40°C

40°C40°C Delay

Multizone Light soiling, for example glasses and cups. X 10.0 0.85 100 Light

P4P4

Rapi

RapiRapid

dd 45°C

45°C

45°C45°C Delay

Multizone Lightly soiled crockery, with no dried-on food. X 11.0 0.80 30 NO

P5P5 Eco

Eco

EcoEco 2)

2)2) 50°C

50°C

50°C50°C Delay

Multizone

Power Clean

Normally soiled crockery.

Energy-saving program. X 6.0 1.03 185 Full

P6P6

Fast Daily

Fast DailyFast Daily 60°C

60°C

60°C60°C Delay

Multizone Normally soiled crockery. X 10.0 1.30 80 Full

P7P7

Silent

SilentSilent 50°C

50°C

50°C50°C Delay

Multizone Normally soiled crockery, gentle and

quiet thanks to the lower spray pressure (39 dBa). X 10.0 1.20 290 Light

P8P8

Intensi

IntensiIntensive

veve 65°C

65°C

65°C65°C Delay

Multizone

Power Clean

Recommended program for heavily soiled

crockery, especially suitable for pans and

saucepans. X 11.0 1.60 145 Full

P9P9 Steam

Steam

SteamSteam Delay

Multizone

Power Clean

Program including steam action dedicated for

heavily soiled crockery, pots and pans. Soaking or

hand pretreatment is no longer needed. X 10.0 1.70 180 Full

P10

P10P10 Hygiene

Hygiene

HygieneHygiene 3)

3)3) Delay

Multizone

Power Clean

Normally or heavily soiled crockery, with additional

antibacterial wash. Program interruption (e.g. due to

door opening) can compromise elimination of germs. X 13.0 1.50 118 Full

5019 396 03667

5019 396 036675019 396 03667

BEFORE USING THE APPLIANCE FOR THE

BEFORE USING THE APPLIANCE FOR THE BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULL

FIRST TIME CAREFULL

FIRST TIME CAREFULLFIRST TIME CAREFULLY READ THIS

Y READ THIS

Y READ THIS Y READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBL

QUICK REFERENCE GUIDE AND THE ASSEMBLQUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Y INSTRUCTIONS!

Y INSTRUCTIONS!Y INSTRUCTIONS!

Options and display description

SAL

SALSALT INDICA

T INDICA

T INDICAT INDICATOR

TOR

TORTOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

RINSE AID INDICATOR

RINSE AID INDICATORRINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to

be refilled.

WASH TIME DISPLAY

WASH TIME DISPLAYWASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

THE CONTROL P

THE CONTROL PTHE CONTROL PANEL OF THIS DISHW

ANEL OF THIS DISHW

ANEL OF THIS DISHWANEL OF THIS DISHWASHER ACTIV

ASHER ACTIV

ASHER ACTIVASHER ACTIVA

AATES PUSHING ANY

TES PUSHING ANY

TES PUSHING ANY TES PUSHING ANY

BUTTON EXC

BUTTON EXCBUTTON EXCEPT CANCEL/OFF BUTTON.

EPT CANCEL/OFF BUTTON.

EPT CANCEL/OFF BUTTON. EPT CANCEL/OFF BUTTON.

FOR ENERGY SA

FOR ENERGY SAFOR ENERGY SAVING THE CONTROL P

VING THE CONTROL P

VING THE CONTROL PVING THE CONTROL PANEL DEACTIV

ANEL DEACTIV

ANEL DEACTIVANEL DEACTIVA

AATES

TES

TES TES

AUTOMA

AUTOMAAUTOMATICALL

TICALL

TICALLTICALLY AFTER 30 SECONDS IF NO CYCLE HAS ST

Y AFTER 30 SECONDS IF NO CYCLE HAS ST

Y AFTER 30 SECONDS IF NO CYCLE HAS STY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

ARTED.

ARTED.ARTED.

MUL

MULMULTIZONE

TIZONE

TIZONETIZONE

Allows you to choose the washing

zones. Press this button (repeatedly)

to select the wash zones:

both racks

only lower rack

only upper rack

- indicator lits

TTABLET SETTING

ABLET SETTING

ABLET SETTINGABLET SETTING

This setting allows to

optimize the cycle

performances according

the type of detergent

used. Push the Tablet

button for 3 seconds

(until the indicator lights

up) if you are using the

combined detergents in

tablet (rinse aid, salt and

detergent in 1 dose). If you

are using powder

detergent or liquid

detergent, the Tablet

indicator on the control

panel has to be off.

DELA

DELADELAYED ST

YED ST

YED STYED START

ART

ART ART

BUTTON

BUTTONBUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to 24

hours. With each press of

the button, the delayed

start indicator increases

by one hour and after

24 restarts from 0. Then

press the START button.

The dishwasher will start

after the set time.

POWER CLEA

POWER CLEAPOWER CLEAN

Thanks to the additional power jets

this option provides a more intensive

and powerful wash in the lower rack,

in the specific area. This option is

recommended for washing pots and

casseroles (see page 4). Press this

button to activate Power Clean

(the indicator lights up).

For non Power Clean loading to

achieve best cleaning performances

and resources optimization, Power

Clean should be switched off.

Quick reference guide

Quick reference guideQuick reference guide

GB -2-

-2-

-2--2-

First time use

5 7 86

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

WWater hardness should be set only

ater hardness should be set only

ater hardness should be set only ater hardness should be set only

before the first wash or if water

before the first wash or if water before the first wash or if water

hardness has been changed

hardness has been changedhardness has been changed

1Visual indicator

(depending

on the model).

Unscrew cap.

(depending on the model)

The salt level indicator lamp may remain lit

at the end of several wash cycles. If the

water hardness level falls within category

(soft), no salt is required.

Salt indica

Salt indicaSalt indicator on the con

tor on the con

tor on the contor on the control panel

trol panel

trol paneltrol panel Salt indicator on the s

Salt indicator on the s

Salt indicator on the sSalt indicator on the salt reservoir cap

alt reservoir cap

alt reservoir capalt reservoir cap

The indicator lamp lights up when SALT

NEEDS TO BE ADDED. green: OK. clear: NEEDS TO

BE ADDED

Daily check

Filling the salt reservoir -

Filling the salt reservoir - Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

- Press and hold together P

PPROGRAM Selection

ROGRAM Selection

ROGRAM SelectionROGRAM Selection and CANCEL/Off

CANCEL/Off

CANCEL/OffCANCEL/Off buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

- Press the PROGRAM Selection

PROGRAM Selection

PROGRAM Selection PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next

press of the start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press Start/Resume

Start/Resume

Start/ResumeStart/Resume button to save setting.

Add salt

Add salt Add salt (never add detergent!)

min. 0.8 kg / max. 1 kg

Screw on the cap.

Salt residual

around the cap

need to be

removed. Some

salt reservoir have

a level indicator

integrated in the

cap (see below

how to check).

Once regeneration salt is added, immediately

immediately

immediatelyimmediately start a wash program (the “Pre-wash” program alone is not

not

notnot sufficient).

Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

1.1. 2.

2.2.Ask your water supply company what the water hardness

water hardness

water hardnesswater hardness is... ...enter this value on

your dishwasher Suggestions for detergent use

German

degrees °dH French

degrees °fH English

degrees °eH Water hardness

level Insert value is shown

in the display Gel or Powder

(rinse aid and salt) Tablets

0 - 5 0 - 9 0 - 6.3 Soft 1

go to step 1

(see “Daily

check”)

6 - 10 10 - 18 7 - 12.6 Medium 2

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 if water is

HARD extra salt

needs to be added

(go to step 1,

“Daily check”)

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Water hardness level is factory

set for medium-hard water

(level 4).

Even if you use tablets which

include salt functionality, you

must still add regeneration salt

since such detergents are not

effective enough at softening

hard water.

At first time use, the salt

At first time use, the salt At first time use, the salt

reservoir has to be filled

reservoir has to be filled reservoir has to be filled

independently from water

independently from water independently from water

hardness level

hardness level hardness level (see description

below in step 1 “Daily check”).

Fill the salt reservoir with water

before the first wash only.

How to set water hardness in order to always assure the best cleaning results

How to set water hardness in order to always assure the best cleaning resultsHow to set water hardness in order to always assure the best cleaning results

GB -3-

-3-

-3--3-

Daily check

Check the rinse aid indicator to check the level

into the dispenser.

(depending on the model)

Rinse aid indicator on the control panel

Rinse aid indicator on the control panelRinse aid indicator on the control panel Rinse aid indicator on th

Rinse aid indicator on th

Rinse aid indicator on thRinse aid indicator on the dispenser

e dispenser

e dispensere dispenser

The indicator lamp lights up when RINSE AID NEEDS

TO BE ADDED. dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immedia

Immedia

ImmediaImmediately

tely

telytely wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the

appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty

drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with

rinse aid incorporated tend to form excess suds.

Daily use

Adding detergent -

Adding detergent - Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the

detergent dispenser

prior to starting a

wash program.

Shut the cover

by pressing dedicated ribs.