Whirlpool WDT975SAHV Manual de Usario

Whirlpool lavavajillas WDT975SAHV

Lee a continuación 📖 el manual en español para Whirlpool WDT975SAHV (2 páginas) en la categoría lavavajillas. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

DRAIN REQUIREMENTS

■

A new drain hose is supplied with your dishwasher.

If drain hose is not long enough, use a new drain hose with a

maximum length of 12 ft (3.7 m) that meets all current AHAM/

IAPMO test standards, is resistant to heat and detergent, and

ﬁts the 1" (25 mm) drain connector of the dishwasher.

NOTE: Do not connect multiple drain hoses together.

■Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20" (508 mm)

minimum above the ﬂoor. It is recommended that the drain

hose either be looped up and securely fastened to the

underside of the counter or be connected to an air gap.

■Make sure to use an air gap if the drain hose is connected

to house plumbing lower than 20" (508 mm) above

subﬂoor or ﬂoor.

■

If required, the air gap should be installed in accordance

with the air gap installation instructions. When you are

connecting the air gap, a rubber hose (not provided) will

be needed to connect to the waste tee or disposer inlet.

■Use 1/2" minimum I.D. drain line ﬁttings.

Use of air gap

Air gap

Undercounter Dishwasher

WATER SUPPLY REQUIREMENTS

■This dishwasher has a water heating feature and also

requires a connection to a hot water supply line.

■A hot water line with 20 to 120 psi (138 to 862 kPa)

water pressure can be veriﬁed by a licensed plumber.

■120°F (49°C) water at dishwasher

■3/8" O.D. copper tubing with compression ﬁtting or ﬂexible

braided water supply line. See the “Tools and Parts” section

at the front of the guide for part details and orders.

NOTE: 1/2" minimum plastic tubing is not recommended.

■A 90° elbow with 3/4" hose connection with rubber washer.

■Do not solder within 6" (152 mm) of the water inlet valve.

■If installed in new construction, make sure the house

water supply lines have been ﬂushed prior to connecting

the dishwasher to remove any debris that may exist in

the supply line.

NOTE: If replacing an existing dishwasher, it is recommended

to install a new water line (see the “Tools and Parts” section at

the front of the guide for part details) and drain hose (supplied)

with the new dishwasher.

ELECTRICAL REQUIREMENTS

■

120-volt, 60 Hz, AC-only, 15- or 20-amp, fused

electrical supply

■Copper wire only

■A maximum of 2 ﬁeld wiring supply conductors

(12 AWG largest size) plus 1 grounding conductor

are permitted in the terminal box.

We Recommend:

■

A time-delay fuse or circuit breaker

■A separate circuit

If Connecting Dishwasher with a Power Cord:

■Use UL Listed power cord kit marked for

use with dishwasher. See the “Tools and

Parts” section at the front of the guide for

part details and orders.

■

Plug into a grounded 3 prong outlet. Outlet must

meet all local codes and ordinances.

If Connecting Dishwasher with Direct Wiring:

■Use ﬂexible, armored, or nonmetallic

sheathed copper wire with grounding

wire that meets the wiring requirements

for your home and local codes and ordinances.

■

Use a UL Listed/CSA Approved metallic strain relief.

See the “Tools and Parts” section at the front of the

guide for part details and orders.

Because Whirlpool Corporation policy includes a continuous commitment

to improve our products, we reserve the right to change materials and

speciﬁcations without notice.

Dimensions are for planning purposes only. For complete details, see

Installation Instructions packed with product. Speciﬁcations subject to

change without notice.

Page 1 of 2

W10806906-D-WH

11/16

PRODUCT MODEL NUMBERS

WDF560SAF

WDF760SAD

WDF770SAF

WDT750SAH

WDT755SAH

WDT780SAE

WDT920SAD

WDT970SAH

WDT975SAH

WDT995SAF

WDTA50SAH

WDTA55SAH

WDTA75SAH

Product and Cabinet Opening Dimensions

237/ "8

(606 mm)

30"

(762 mm)

31/ " - 421/ "2

(88 mm - 106 mm)

331/ "2

(851 mm)

min. with

wheels

removed

241/ "2

(622 mm)

3/ "4

(19 mm)

30"

(762 mm)

33/ "4

(94 mm)

21"

(533 mm)

24"

(620 mm)

24"

(620 mm)

34"

(864 mm)

(76 mm)

13/ "4

(44 mm)

63/ "4

(172 mm)

21/ "4

(64 mm)

21/ "4

(64 mm)

(51 mm)

/ "4

(159 mm)

101/ "2

(267 mm)

(102 mm)

A. Insulation may be compressed (not used on all models).

B. For panel-ready models, dishwasher depth is 24" (610 mm),

not including the 3/4" (19 mm) custom door panel.

C. Door handles may protrude forward of the face of the

dishwasher, varies by model.

For 4" (100 mm) toe kick, height of cabinet opening is 341/2" (863 mm).

Check that all surfaces have no protrusions

that would prohibit dishwasher installation.

D. Measured from the lowest point on the underside

of the countertop. May be reduced to 33

1/2"

(851 mm) by removing the wheels and perforated

area of insulation (blanket) on dishwasher.

E. Minimum, measured from narrowest point

of opening

NOTE: Shaded areas

of cabinet walls

show where utility

connections may

be installed.