Whirlpool XHPC155XW Manual de Usario

Whirlpool No categorizado XHPC155XW

Lee a continuación 📖 el manual en español para Whirlpool XHPC155XW (16 páginas) en la categoría No categorizado. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/16

15.5" PEDESTAL INSTALLATION INSTRUCTIONS

For use only with front load washers and dryers

INSTRUCTIONS D’INSTALLATION DU PIÉDESTAL DE 15,5"

Pour utilisation avec les produits suivants seulement

laveuses et sécheuses à chargement par l’avant

W10347252B

W10348602B - SP

Table of Contents Table des matières

PEDESTAL SAFETY ......................................................1

INSTALLATION REQUIREMENTS ................................2

Location Requirements .........................................2

Tools and Parts .......................................................2

UNPACKING THE PEDESTAL ......................................3

BEFORE INSTALLING THE PEDESTAL .......................3

INSTALLING THE PEDESTAL .......................................4

COMPLETE THE INSTALLATION .................................7

SÉCURITÉ DU PIÉDESTAL ..........................................9

EXIGENCES D’INSTALLATION ....................................9

xigences d’emplacement ....................................9E

Outillage et pièces .................................................9

INSTRUCTIONS D’INSTALLATION ............................10

AVANT L’INSTALLATION DU PIÉDESTAL .................11

INSTALLATION DU PIÉDESTAL .................................12

ACHEVER L’INSTALLATION .......................................15

INSTALLATION NOTES

Date of purchase: _________________________________

Date of installation: _______________________________

Installer: ________________________________________

Model number: ___________________________________

Serial number: ___________________________________

NOTES CONCERNANT L’INSTALLATION

Date d’achat : _____________________________________

Date d’installation : ________________________________

Installateur : ______________________________________

Numéro de modèle : ________________________________

Numéro de série : __________________________________

PEDESTAL SAFETY

Para una versión de estas instrucciones en español, visite www.whirlpool.com

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools Needed:

Utility knife 1/4" hex-head ratchet

or open-end wrench

Level 9/16" open-end wrench

Pliers or slip-joint pliers Bucket

INSTALLATION REQUIREMENTS

LOCATION REQUIREMENTS

NOTE: If the washer/dryer and pedestal assembly are located in

a garage, 3 (76 mm) must be added under the pedestal so that "

the washer/dryer is 18" (458 mm) above the garage oor.

Towel Sponge

Parts Supplied:

Four #12 x 3/4" hex-head Drawer divider

sheet metal screws

Additional Items Needed:

1/4" nut driver 5/16 hex-head ratchet "

or nut driver

NOTE: If the washer is to be transported, call your local service

center. To avoid suspension and structural damage, your

washer must be properly set up for relocation by a certied

technician.

1. Turn off the hot and cold water faucets.

2. Unplug the power supply cord.

3. Slowly loosen the ll hoses at the faucets to relieve the water

pressure. Use a sponge or towel to absorb the released water.

4. Remove the “HOT” and “COLD” ll hoses from the back of

the washer. Drain the water from the hoses into a bucket.

5. Remove the drain hose from the standpipe or laundry tub and

drain any water remaining in the hose into a bucket.

6. Pull the washer away from the wall so that you will have

enough space for the installation.

1. Empty pedestal drawer

UNPACKING THE PEDESTAL

Preparing the pedestal for installation

Open the pedestal drawer as far as possible and remove the

contents. The package contains four #12 x 3/4" hex-head

sheet metal screws and a drawer divider.

IMPORTANT: Set the pedestal box aside for use during

installation.

Hex-head screw

Drawer slide

3. Remove pedestal drawer

Using a 1/4" nut driver, remove the hex-head screws from both

drawer slides and save screws. Remove the drawer from the

slides and set aside. Push the slides back into the pedestal.

BEFORE INSTALLING PEDESTAL

IMPORTANT: If your washer and dryer are already installed,

they must be uninstalled.

Uninstalling your washer

To avoid possible damage to the washer, the transport bolts on

the back of the washer must be in place before installing the

pedestal. For more information on transport bolts see, “Remove

Transport System” in washer Use and Care Guide.

The four spacer pads are installed on the top of the pedestal.

These pads reduce vibration between the pedestal and the

washer/dryer.

NOTE: If your washer/dryer has feet installed, remove them.

Spacer pads

2. Locate spacer pads

Especificaciones del producto

Marca:	Whirlpool
Categoría:	No categorizado
Modelo:	XHPC155XW
Tipo de operación:	Knoppen
Color del producto:	Roestvrijstaal
Ancho:	900 mm
Profundidad:	485 mm
Altura:	- mm
Nivel de ruido:	52 dB
Amable:	Muurmontage
Número de motores:	1
Capacidad máxima de extracción:	639 m³/uur
Método de extracción:	Afvoerend/recirculerend
Número de lámparas:	2 gloeilamp(en)
Tipo de lámpara:	LED
Altura (mín.):	620 mm
Altura (máx.):	1115 mm
Lámpara de encendido:	2.5 W
Número de filtros:	3 stuk(s)
Número de velocidades:	3