WilTec 51547 Manual de Usario

WilTec bomba de agua 51547

Lee a continuación 📖 el manual en español para WilTec 51547 (9 páginas) en la categoría bomba de agua. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/9
User’s Manual
Multi-stage Centrifugal Pump
51545–51547, 63906 63907–
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
https://www.XPOtool.com Item 51545–51547 , 63906–63907 Page 2
The Tool Experts
02 2023-1
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate, and up- -date, errors cannot be ruled out entirely.to
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
service@wiltec.info
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler – Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler – Germany
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
https://www.XPOtool.com Item 51545–51547 , 63906–63907 Page 3
The Tool Experts
02 2023-1
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Safety instructions
The symbols and the sentences including the words or “danger” “warning” wish to call
your attention to the dangers and possible consequences of non-compliance with the safety instructions.
Symbol
Danger: Non-compliance with the safety instructions might …
… lead to an electric shock.
… cause severe damages caused to your health.
… damage the pump.
General remarks
• Make sure that the product has been installed correctly to work at its best.
• All materials have undergone a meticulous inspection. Installing correctly the pump contributes
to the protection of the pump against damages and overcharge. Any non-compliance with the
instructions can cause damages to the pump.
• Always use a non-return valve.
• The pump must not be immerged into water. The water is sucked in via a hose.
• Prime the pump and suction line with water before using it; otherwise, it will run the risk of
running dry.
• Check if there is a water column (prime the pump with water before use until the water column
is present to 100 % ).
Assembly
• The pump must be set up on a level and firm surface.
• The end of the suction line should be immerged at least 30 cm at the lowest point of the water.
• The suction line must have a slope in w -sampling direction; that must be done so that the ater
line has no bends that could provoke a water accumulation.
• Never hang up the pump by an electric cable or line.
• Before use, make sure that there is a continuous water column.
• It is advisable that you install a tube with a larger diameter than that of the outlet to reduce the
friction loss as much as possible.
• Install a non-return valve to the entry of the pump to prevent that the line is emptied at every
stop of the pump.
• Avoid that tube lines are bent or twisted and make sure that the connection to the outlet is
correct. In both cases, the flow at the outlet is reduced if the connection be bad.
Checks before start
• Make sure that the existing mains voltage and frequency match the specifications on the name-
plate of the device.

Especificaciones del producto

Marca: WilTec
Categoría: bomba de agua
Modelo: 51547

¿Necesitas ayuda?

Si necesitas ayuda con WilTec 51547 haz una pregunta a continuación y otros usuarios te responderán


bomba de agua WilTec Manuales

WilTec

WilTec 63910 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 50967 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 50453 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 52007 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 50965 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 50266 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 50268 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 51541 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 50921 Manual de Usario

9 Septiembre 2024
WilTec

WilTec 51561 Manual de Usario

9 Septiembre 2024

bomba de agua Manuales

Últimos bomba de agua Manuales

Hydro-Pro

Hydro-Pro Inverter 26 Manual de Usario

27 Octubre 2024
Elpumps

Elpumps VB 50/1500 B Manual de Usario

26 Octubre 2024
Hyundai

Hyundai HY80 Manual de Usario

21 Octubre 2024
Einhell

Einhell GC-DP 1020 N Manual de Usario

20 Octubre 2024
Dimplex

Dimplex WI 22 TE Manual de Usario

11 Octubre 2024
Hayward

Hayward S240SLETL Manual de Usario

9 Octubre 2024
Einhell

Einhell GE-WW 5537 E Manual de Usario

8 Octubre 2024
Daikin

Daikin EKHBRD016ABV1 Manual de Usario

4 Octubre 2024
Dimplex

Dimplex WI 10TU Manual de Usario

4 Octubre 2024
Dimplex

Dimplex WI 40 CS Manual de Usario

2 Octubre 2024