Yamaha VXS8 Manual de Usario

Yamaha Vocero VXS8

Lee a continuación 📖 el manual en español para Yamaha VXS8 (2 páginas) en la categoría Vocero. Esta guía fue útil para 14 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of

serious injury or even death from electrical shock, short-circuiting, damages,

fire or other hazards. These precautions include, but are not limited to, the

following:

• This device contains no user-serviceable part s. Do not open the device or attempt

to disassemble the internal parts or modify them in any way. If it should appear to

be malfunct ioning, discontinue use immediately and have it inspect ed by qualified

Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of

physical injury to you or others, or damage to the device or other property.

These precautions include, but are not limited to, the following:

• Do not place the device in an unstable position where it might accidentally fall over.

• Do not place the device in a location where it may come into contact with corrosive

gases or salt air. Doing so may result in malfunction.

• Do not place the device where it is always exposed to water. Doing so may result in

malfunction.

• Do not place the device where it is exposed to oil. Doing so may result malfunction.

• Construction work should be carried out in accordance with construction-related

law and always by a professional constructor. If the device installation requires

construction work, make sure to observe the following precautions.

- Choose mounting hardware and an installation location that can support the

weight of the device.

- Avoid locations that are exposed to constant vibration.

- Use the required tools to install the device.

- Inspect the device periodically.

• Before connecting t he device to a power amplifier, t urn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to minimum.

• Use only speaker cables for connecting speakers to the speaker connectors. Use of

other types of cables may result in fire.

• Do not wipe the outer packaging with benzine, thinner, or synthet ic detergent and

do not use electrical contact cleaner. These may damage the outer packaging and

dissolve the parts.

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) int o holes of

the grille. If this happens, have the device inspected by qualified Yamaha service

personnel.

• Do not operate the device if the sound is distorting. Prolonged use in this condit ion

could cause overheating and result in fire.

• When choosing a power amplifier for use with this device, make sure that the output

power of the amplifier is lower than the power capacity of this device (see

SPECIFICATIONS).

Even if the output power of the amplif ier is lower than the power capacity of this

device (PGM), use of excessive input signals resulting in clipping may cause

damage to the device.

Malfunction or fire may occur especially when the following sounds or noises are

generated:

- feedback, when using a microphone

- cont inuous and extreme volume sound from a musical instrument

- extreme continuous dist orted sound

- noise caused by plugging/unplugging the cable while the amplifier is turned on

PRECAUTIONS

Do not open

Location

Connections

Maintenance

Handling caution

NOTICE

To avoid the possibility of malfunction/damage to the product or damage to other

property, follow the notices below.

ƔHandling and Maintenance

• Do not place vinyl, plastic or rubber objects on the device, since this might discolor

the panel.

• When cleaning the device, use a dry and soft cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic changes in ambient

temperature-when the device is moved from one location to another, or air

conditioning is turned on or off, for example. Using the device while condensation is

present can cause damage. If there is reason to believe that condensat ion might

have occurred, leave the device for several hours until the condensation has

completely dried out.

• Be sure to observe the amplifier’s rated load impedance (see SPECIFICATIONS),

particularly when connecting speakers in parallel. Connect ing an impedance load

out side the amplifier’s rated range can damage the amplifier.

• When connecting the speakers wit h high impedance, be sure that the out put total of

each speaker does not exceed the rated output of the power amplifier.

• When using a high-impedance speaker connection, make sure the audio signal is

passed through an 80 Hz or above high-pass filter before being input to the

speakers. For VXS5/VXS5W, UL Listing is void without this connect ion.

• ABOUT THE PROTECTION CIRCUIT

This speaker system has an internal protection circuit that shut s off the speaker unit

when an excessive input signal is applied.

If the speaker unit emits no sound, reduce the volume level of the amplifier

immediately.

The sound will return automat ically in several seconds.

• Place the speaker on a flat and smooth surface.

• Do not place the speaker on the ground with the grille faced down.

• Do not touch the speaker driver unit.

ƔAbout This Manual

The illustrations as shown in this manual are f or instructional purposes only, and may

appear somewhat different from those on your device.

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the device.

Information for Users on Collection and Disposal of Old Equ ipment

This symbol on the products, packaging, and/or accompanying

documents means that used electrical and electronic products should no t

be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take

them to applicable collection points, in accordance with your national

legislation and the Directives 2002/96/EC.

By disposing of these products correct ly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local

municipality, your waste disposal service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or

supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please

contact your local authorities or dealer and ask for the correct method of disposal.

UNPACKING

Unpack the contents and confirm that all the following items are included.

• Speaker × 2

• Bracket base × 2

• Mounting bracket × 2

• Bracket cover × 2

• Screw for attaching the mounting bracket × 4 (VXS8/VXS8W: M6, VXS5/VXS5W: M5)

• Stopper screw × 2 (M3, VXS8/VXS8W only)

• Bolt with hexagon hole × 2

• Safety wire × 2

• Terminal cover × 2

• Safety pin × 2

• Hexagon wrench × 1

• Owner’s Manual (this manual)

* Screws/bolts to fasten the bracket base onto the wall/ceiling and speaker cables are not included.

SPECIFICATIONS

*1: Half-space (2π)

*2: Calculated based on power rating and sensitivity, exclusive of power compression.

*3: When connecting with low impedance

*4: IP34 when installing the speaker to the ceiling vertically.

The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual

may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since

specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yama ha dealer.

The dimensions are shown overleaf.

VXS8/VXS8W VXS5/VXS5W

Type 2-way, Bass-reflex

Component LF 8" (20 cm) Cone driver 5-1/4" (13 cm) Cone driver

HF 1" (2.5 cm) Soft dome tweeter 3/4" (2 cm) Soft dome tweeter

Coverage angle (500 Hz – 4 kHz on average) 100° H × 100° V 120° H × 120° V

Nominal impedance 8 Ω

Power rating NOISE 90 W 75 W

PGM 180 W 150 W

MAX 360 W 300 W

Sensitivity (1W, 1m) * 191 dB SPL 89 dB SPL

Maximum SPL (Calculated, 1m) * 2117 dB SPL 114 dB SPL

Frequency range (-10 dB) * 1, *351 Hz – 20 kHz 62 Hz – 20 kHz

Crossover frequency 2.8 kHz 3 kHz

Connector Euroblock (4 pin) × 1 (input: +/-, loop-thru: +/-)

Max. wire size 12 AWG (2.5 mm 2)

Transformer taps 70 V 60 W, 30 W, 15 W, 7.5 W 30 W, 15 W, 7.5 W, 3.8 W

100 V 60 W, 30 W, 15 W 30 W, 15 W, 7.5 W

Overload protection Full-range power limiting to protect network and transducers

Magnetically shielded No

Dust and water resistant * 4IP35

Enclosure Shape Rectangle

Cabinet material ABS

Baffle material PC/ASA

Grille material Powder coated perforated aluminum (t=1 mm)

Aperture ratio: 51%

Finish VXS8/VXS5: Black (Not painted, approximate value: Munsell N3)

VXS8W/VXS5W: White (Not painted, approximate value: Munsell 9.3)

Dimensions (Speaker only)

(W × H × D in vertical cabinet orientation)

278 × 430 × 239 mm

(10.9" × 16.9" × 9.4")

176 × 280 × 163 mm

(6.9" × 11.0" × 6.4")

Net weight (Speaker only, 1 piece) 8.2 kg (18.1 lbs) 3.6 kg (7.9 lbs)

Packaging Packaged in pair

INSTALLING THE SPEAKERS

Install the speakers onto the wall/ceiling with the supplied brackets. Ensure

that the wall/ceiling is sufficiently strong.

Illustrations in this manual are for the VXS5. The installation method is the

same for other models.

Pre-installation (Preparation of the cable)

Use stranded wire for cables attached to the Euroblock connector. Strip

their insulation as shown in the figure and connect them.

NOTE

Do not plate stranded wires by solder. Doing so will cause the wire to break.

An installed speaker is shown below. Install the bracket base and attach the

mounting bracket as shown.

NOTE

• When installing the speaker to the ceiling with the grille parallel to the

ground, install the speaker horizontally.

• When installing the speaker to the ceiling, be sure to install the bracket

base with its shaft facing horizontally, and not inclined to the ground.

• Mounting bracket is made to not turn left or right when installing the

speaker to the ceiling.

1Put the bracket base onto the wall/ceiling and mark the position for

the screws/bolts and cables. The diameter of the screw/bolt holes at

the four corners is M6, and speaker cables hole at the center is

ø11 mm.

2Make holes through the wall/

ceiling for the bolts and cables,

as required, and feed the bolts

and cables from the amplifier

through the holes, as shown.

3Install the bracket base onto

the wall/ceiling. Make sure to

fasten four corners of the

bracket base.

4Pass cables through the gap at

the lower part of the bracket

cover, and put the bracket

cover on the bracket base.

NOTE

If you want to adjust the slack of

cables last, the bracket cover

can be attached after step 5-6.

Installing to the wall Installing to the ceiling

VerticalHorizontal

1INSTALL THE BRACKET BASE ONTO THE WALL /CEILING

About 7 mm (0.3 in.)

Bracket cover

Bracket base

1Remove the Euroblock connector.

2After loosening the terminal screws of the Euroblock connector with a

flat-blade screwdriver, insert the cable into each terminal and tighten

the screws. Make sure that cables cannot be pulled out.

NOTE

Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).

There are two acceptable wiring methods.

CAUTION

When connecting with low impedance, take note of the combined

resistance.

Using Loop-Through Terminals

For this method, cables are connected from terminals 1 and 4 to the

subsequent speaker. If the Euroblock connector is disconnected from

a speaker, all subsequent speakers will not work. This can be useful

to identify which speaker has a problem.

Paralleling Input Terminals

For this method, cables are connected to terminals 2 and 3 of each

speaker. Since the cables are connected via Euroblock connectors,

subsequent speakers can work even if a problem occurs with a

speaker.

2CONNECT THE WIRING TO THE CONNECTOR

Euroblock connector

Less than 3 mm (0.1 in.)

From amplifier or

previous speakers To subsequent

speakers

subsequent

speakers

Euroblock

connector

Power

amplifier

Speaker

From amplifier or

previous speakers

To subsequent

speakers

Power

amplifier

Speaker

Euroblock

connector

subsequent

speakers

Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/

70V line distributed system, by rotating the tap selector switch on the rear

side of the speaker with a flat-blade screwdriver.

CAUTION

• The “X” position should not be selected. The 8Ω position should be

selected for 8Ω audio systems only. If the setting is incorrect, it may

cause malfunction of the speaker and amplifier.

• Make sure the amplifier is switched off before operating the tap selector

switch.

1Attach the mounting bracket and safety wire to the speaker. Use the

supplied screws to attach the mounting bracket.

The way to attach the mounting bracket depends on the orientation of

the speaker (vertical or horizontal).

2Set the desired vertical angle of the speaker.

Loosen the angle adjustment bolt with the supplied hexagon wrench,

adjust the angle of the speaker, and tighten the angle adjustment bolt

to fix the speaker (indication of torque: 8 N·m).

NOTE

• Guide marked on the mounting bracket is every 10°.

• (VXS8/VXS8W only) When installing the speaker to the wall with a

vertical angle of 30° or less, attach the supplied stopper screw.

1Install the mounting bracket to the bracket base.

3SET THE LINE VOLTAGE/IMPEDANCE AND POWER

4ATTACH THE MOUNTING BRACKET AND SAFETY WIRE

NOTE

Mounting bracket can be attached in reverse direction.

5INSTALL THE SPEAKER TO THE BRACKET BASE AND FIX

THE CABLE

Illustration indicates the setting at 30 W for 100 V

line and 15 W for 70 V line.

Mounting bracket

Safety wire

Stopper screw

(VXS8/VXS8W only)

Vertical installation

Angle

adjustment bolt

Angle adjustment

bolt

Horizontal installation

Stopper screw

(VXS8/VXS8W only)

To the wall To the ceiling

2Attach the safety pin.

Be sure to attach the safety pin to prevent the mounting bracket from

falling.

NOTE

The safety pin can be attached from either side of the mounting

bracket depending on the angle of the speaker.

3Plug the Euroblock connector into the socket in the speaker.

4Attach the terminal cover.

5(If installing the speaker to the wall) turn the speaker horizontally to

set the angle.

6Make sure the mounting bracket is seated against the bracket base,

then tighten the supplied bolt (indication of torque: 6.5 N·m).

NOTE

• When installing the speaker to the ceiling in particular, make sure

the mounting bracket is seated against the bracket base.

• The bolt with hexagon hole can be attached from either side of the

mounting bracket (left or right) depending on the angle of the

speaker.

7Install the safety wire to the wall/ceiling.

CAUTION

• Make sure to take measures to prevent the speaker from falling

down in the event of a installation failure.

• When installing the safety wire to the wall, install it higher than the

wire’s attachment point on the speaker, with as little slack as

possible.

• If the safety wire is too short, prepare another wire appropriate for

the speaker weight and installation conditions. If the wire is too

long, should the speaker fall, the wire may snap as a result of too

much strain.

Safety pin

Terminal cover

Bolt with hexagon hole

Owner’s Manual

Surface Mount Speaker

English

ZE85530

DIMENSIONS

239

163

VXS8/VXS8W

VXS5/VXS5W

Bracket base

Unit: mm

VXS8/VXS8W

Mounting bracket

VXS8/VXS8W

VXS5/VXS5W VXS5/VXS5W

Manual Development Department

Published 03/2015 YKZC-D0

Printed in Indonesia

Yamaha Pro Audio global web site

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Especificaciones del producto

Marca:	Yamaha
Categoría:	Vocero
Modelo:	VXS8
Peso.:	260 g
Ancho:	76.2 mm
Profundidad:	127 mm
Altura:	31 mm
Certificados de sostenibilidad:	RoHS
Cantidad por paquete:	63 stuk(s)
Voltaje de entrada:	90 - 264 V
Potencia de salida:	75 W
Abarcando:	36 V