ZLine KBAR30 Manual de Usario

ZLine campana extractora KBAR30

Lee a continuación 📖 el manual en español para ZLine KBAR30 (11 páginas) en la categoría campana extractora. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/11

Designer Wall Range Hood Installation

Installation

Tutorial Video

*Note: Wall range hoods with single motors will come with a square to 6˝ round transition piece

and will include a backdra damper. e ducting with these range hoods is 6˝.

Dual motor wall hoods will come with a square to 8˝ round transition piece without a backdra

damper. e ducting with these range hoods is 8˝.

*Note: Use rigid ducting wherever possible. Try and minimize the use of elbows. More elbows

and longer runs create higher static pressure. e hood comes with a grounded three prong plug

that can either be direct wired or plugged into a 20 amp. circuit.

1. Main Hood With All Lights and

Button Banks Pre-installed

2. Chimney

3. Transition Piece (For 6˝ or 8˝)

4. Bae Filters

5. Flexible Duct (For 6˝ or 8˝)

6. Packet of Screws and Anchors

7. Top Mounting Bracket

8. Crown Molding Bracket

9. Crown Molding

Grease Cup

10.

Parts Supplied:

Please unpack your range hood when it is delivered

and inspect to ensure all parts are included.

Designer Wall Range Hood Installation

*e recommended height to install your hood is 30 minimum and 36˝ ˝ maximum

above the cooktop.

*For Outdoor (304 Series) hood installation: e unit must be installed at a minimum

of 36 above the grill. ˝

Find the center of the wall where you

are installing the hood. Make sure

there is sucient bracing to hold the

weight of the hood. Mark your center

line and measure out from the center

to nd your two mounting points.

Make sure your mounting points are

level when you mark them. It is rec-

ommended to install the hood direct-

ly into wood supports. (Figure 1)

Mark your mounting points and in-

stall the two mounting screws provid-

ed leaving the heads out ¼ to mount ˝

hood. (Figure 1)

Mount the main body of the hood to

the two screws and screw into place.

(Figure 2)

Mount the crown molding bracket

centering it above the hood. (Figure3)

Figure 1

Figure 2

Figure 3

Designer Wall Range Hood Installation

Especificaciones del producto

Marca:	ZLine
Categoría:	campana extractora
Modelo:	KBAR30
Color del producto:	Zwart
Ancho:	160 mm
Profundidad:	440 mm
Altura:	44.6 mm
Indicadores LED:	Activity, Link, Power
Estándar de red:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x
Temperatura de almacenamiento:	-40 - 70 °C
Humedad de almacenamiento:	5 - 95 procent
Montaje en bastidor:	Ja
MDI/MDI-X automático:	Ja
Capacidad de conmutación:	2000 Gbit/s
Dirección MAC:	8000 entries
soporte 10G:	Nee
Tipo de interruptor:	Unmanaged
Número de puertos Ethernet RJ-45 de conmutación básica:	16
Tipo de conmutación básica de puertos Ethernet RJ-45:	Gigabit Ethernet (10/100/1000)
Duplex completo:	Ja
Autonegociación:	Ja
voltaje-de-entrada-de-CA:	100 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Temperatura de funcionamiento (TT):	0 - 40 °C
Humedad relativa de funcionamiento (VV):	10 - 90 procent
Función de autoaprendizaje de dirección MAC:	Ja
Velocidad de reenvío de paquetes (10 Mbps):	14880 pps
Velocidad de reenvío de paquetes (100 Mbps):	148800 pps
Velocidad de reenvío de paquetes (1 Gbps):	1488000 pps